SIGMA TEK RFID 131 Manuale utente
RFID 131
RFID Reader
with USB and CAN Connection
Date of creation: 22.12.2016
Version date: 01.07.2020
Article number: 01-691-131-E
Publisher: SIGMATEK GmbH & Co KG
A-5112 Lamprechtshausen
Tel.: 06274/4321
Fax: 06274/4321-18
WWW.SIGMATEK-AUTOMATION.COM
Copyright © 2016
SIGMATEK GmbH & Co KG
Translation from German
All rights reserved. No part of this work may be reproduced, edited using an electronic system, duplicated or dis-
tributed in any form (print, photocopy, microfilm or in any other process) without the express permission.
We reserve the right to make changes in the content without notice. The SIGMATEK GmbH & Co KG is not responsi-
ble for technical or printing errors in the handbook and assumes no responsibility for damages that occur through
use of this handbook.
RFID READER RFID 131
01.07.2020 Page 1
RFID Reader RFID 131
The RFID reader is an installable device for reading and writing to RFID card. Communica-
tion with other bus participants is established over the CAN bus or USB interface. The
reader is supplied with +24 V.
The RFID reader is installed in a cutaway of the control cabinet. The status LED in the
upper left corner blinks in a 1 s cycle and indicates the readiness of the device. With a CAN
message, it can also be controlled via the application.
RFID 131 RFID READER
Page 2 01.07.2020
Contents
1Technical Data ........................................................................ 4
1.1 Performance Data.........................................................................4
1.2 Electrical Requirements...............................................................4
1.3 RFID Reader ..................................................................................4
1.4 Environmental Conditions...........................................................5
1.5 Miscellaneous ...............................................................................5
2Mechanical Dimensions......................................................... 6
3Connector Layout................................................................... 7
3.1 Applicable Connectors.................................................................8
4Mounting Instructions............................................................ 9
4.1 Mounting Position ........................................................................9
5General Instructions..............................................................10
5.1 Ground.........................................................................................10
5.1 Shielding......................................................................................10
5.2 ESD Protection............................................................................10
5.3 User Guidelines ..........................................................................11
6CAN Bus.................................................................................12
6.1 Node ID Assignment...................................................................12
6.1.1 Node-IDs (CAN Open SDO)..............................................................12
6.2 Number of CAN Bus Participants .............................................13
RFID READER RFID 131
01.07.2020 Page 3
6.3 CAN Bus Data Transfer Rate .....................................................14
6.4 CAN Bus Termination.................................................................15
6.5 CAN Protocol...............................................................................15
6.5.1 CAN Object Definition....................................................................... 15
6.5.2 CAN –Object Dictionary................................................................... 16
6.5.3 Serial Interface.................................................................................. 17
6.5.4 Example Communication - Scanning Tags....................................... 17
7USB Interface Connections..................................................23
7.1 Use with Windows-based Systems...........................................23
8FCC Statement.......................................................................24
9Cleaning the Front.................................................................25
10 Disposal .................................................................................26
RFID 131 RFID READER
Page 4 01.07.2020
1 Technical Data
1.1 Performance Data
Protocol
ISO 15693, ISO 14443A, ISO 14443B
Supported cards
Mifare Ultralight/Ultralight C
Mifare Classic Mini/1K/4K
Mifare Desfire EV1 2K, 4K 8K
Mifare Pro, Plus
ISO15693 NXP ICOD SLI, TI TagIT, standard cards
RF power
100 mW EIRP
Operating frequency
13.56 MHz
Reading distance
up to 5 cm
(depending on the tag, antenna and ambient conditions)
Write distance
approximately 70 % of the read distance
Interfaces
1x USB device 2.0, (Type Mini-B)
1x CAN bus
Status LEDs
yes, blinks in 1 s frequency and indicates the readiness of the device
1.2 Electrical Requirements
Supply voltage
typically +24 V DC
minimum +18 V DC
maximum +30 V DC
Current consumption
Power supply +24 V
minimum 45 mA
maximum 60 mA
Inrush current
2 A for 2 ms
1.3 RFID Reader
Dimensions
90 x 57 x 30.8 mm (W x H x D)
Material
front: acrylic glass
back: chromated sheet steel
Weight
110 g
RFID READER RFID 131
01.07.2020 Page 5
1.4 Environmental Conditions
Storage temperature
-20 ... +85 °C
Environmental temperature
0 ... +55 °C
Humidity
0-95 %, non-condensing
EMC resistance
according to EN 61000-6-2 (industrial area)
EMC noise generation
according to EN 61000-6-4 (industrial area)
Radio Communication Conformity
Europe
according to ETSI EN 300 330 (2014/53/EU, RED Directive)
Radio Communication Conformity
USA
FCC CFR 47 Part 15
Product safety
EN 60950-1:2006
Vibration resistance
EN 60068-2-6
2-9 Hz: amplitude 3.5 mm
9-200 Hz: 1 h (10 m/s2)
Shock resistance
EN 60068-2-27
duration 11 ms, 18 Shocks
15 g (150 m/s2)
Protection type
EN 60529
protected through the housing
front: IP65
cover: IP20
1.5 Miscellaneous
Article number
01-691-131
Hardware version
2.x
RFID 131 RFID READER
Page 6 01.07.2020
2 Mechanical Dimensions
RFID READER RFID 131
01.07.2020 Page 7
3 Connector Layout
X1: USB-Device 2.0 (Type Mini-B)
n.c. = do not use
X2: CAN Bus (5-pin Phoenix Contact)
X3: Visualization (4-pin Phoenix Contact)
Pin
Function
1
+5 V
2
D-
3
D+
4
n.c.
5
GND
Pin
Function
1
CAN A (LOW)
2
CAN B (High)
3
CAN A (CAN LOW)
4
CAN B (High)
5
CAN GND
Pin
Function
1
+24 V supply
2
+24 V supply
3
GND
4
GND
RFID 131 RFID READER
Page 8 01.07.2020
S1: DIP-Switch
3.1 Applicable Connectors
Connectors:
X1: USB Type Mini-B on a USB Type A cable, max. length 3 m
(not included in delivery)
X2: 5-pin Phoenix plug with spring terminals FK-MCP 1.5/ 5-ST-3.5
(Included with delivery)
X3: 4-pin Phoenix plug with spring terminals FK-MCP 1.5/ 5-ST-3.5
(Included with delivery)
Connections:
Stripping length:
10 mm
Mating direction:
parallel to the conductor axis or circuit board
Conductor cross section rigid:
0.2-1.5 mm2
Conductor cross section flexible:
0.2-1.5 mm2
Conductor cross section AWG/kcmil:
24-16
Conductor cross section flexible with
ferrule without plastic sleeve:
0.25-1.5 mm2
Conductor cross section flexible with
ferrule with plastic sleeve:
0.25-0.75 mm2 (reason for reduction d2 of the
ferrule)
Indice
