Silver 5 Thread Manuale utente
Instruction Manual
Cover & Overlock
Important safety instructions
1
When using an electrical appliance, basic safety should always be followed, including the
following:
Read all instructions before using this sewing machine.
-To reduce the ris of electric shoc :
1. An appliance should never be left unattended when plugged in.
2. Always unplug this appliance from the electric outlet immediately after using and before
cleaning.
3. The sewing machine is equipped with a LED lamp. If the LED lamp is bro en, it must be
replaced by the manufacturer or its service agent in order to avoid a hazard.
-To reduce the ris of burns, fire, electric shoc , or injury to persons:
Never use the sewing machine if the air vents are bloc ed. Keep the air vents of the sewing
machine and the food pedal free from dust, fusel and leftovers.
21. Always unplug the sewing machine if you leave it unattended, in order to avoid injuries by
inadvertently switching on the sewing machine.
22. Don't use the sewing machine if it's wet or in humid environment.
23. Keep the instructions at a suitable place close to the sewing machine and hand it over if you
give the sewing machine to a third party.
This sewing machine is intended for household use only.
DANGER
WARNING
SAVE THESE INSTRUCTIONS
1. Do not allow to be used as a toy. Close attention is necessary when this appliance is used by
or near children.
2. Use this appliance only for its intended use as described in this manual. Use only the
attachments recommended by the manufacturer as contained in this manual.
3. Never operate this appliance if it has a damaged cord or plug, if it is not wor ing properly, if it
has been dropped or damaged, or dropped into water. Return the appliance to the nearest
authorized dealer or service center for examination, repair, electrical or mechanical adjustment.
4.
5. Keep fingers away from all moving parts. Special care is required around the sewing machine
needle.
6. Always use the proper needle plate, a wrong needle plate can cause the needle to brea .
7. Do not use bent needles.
8. Do not pull or push fabric while stitching. It may deflect the needle causing it to brea .
9. Switch the sewing machine off ("O") when ma ing any adjustments in the needle area, such as
threading needle, changing needle, threading bobbin, or changing presser foot, and the light.
10. Always unplug sewing machine from the electrical outlet when removing covers, lubricating,
or when ma ing any other user servicing adjustments mentioned in the instruction manual.
11. Never drop or insert any object into any opening.
12. Do not use outdoors.
13. Do not operate where aerosol spray products are being used or where oxygen is being
administered.
14. To disconnect, turn all controls to the off ("O") position, then remove plug from outlet.
15. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
16. The sound pressure level under normal operating conditions is 75dB(A).
17. Please turn off the machine or unplug when the machine is not operating properly.
18. Never place anything on the foot controller.
19. This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lac of experience and nowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety.
20. Children should be supervised to ensure that they do not play with the appliance.
Principal parts of the machine ...........................................................................3-5
Accessories ...........................................................................................................6
Looper cover/ Waste container.............................................................................7
Telescopic thread guide/ Foam pads/ Cone holders/ Thread net/
Thread unreeling disc ..........................................................................................8
Needle position .....................................................................................................9
Presser foot lifting lever ........................................................................................9
Changing a needle..............................................................................................10
Connecting the machine to the power source....................................................11
Starting sewing....................................................................................................12
Adjusting presser foot pressure ..........................................................................12
Threading the thread guides...............................................................................13
Threading the upper overedge looper ................................................................14
Threading the lower overedge looper.................................................................15
Double chainstitch and cover stitch looper....................................................16-17
Threading the needles ...................................................................................18-20
Needle threader ..................................................................................................21
Summary of threading paths and threading sequences ...............................22-24
Thread cutter/ Chec spring for edging the thread chain/ Waste container ......25
Disengage the upper nife..................................................................................26
Swiveling stitch width latch .................................................................................27
2-thread converter...............................................................................................28
Disengage the upper looper ...............................................................................29
Adjusting the stitch length/ Differential feed .......................................................30
Remove nife guard............................................................................................31
Set seam width ...................................................................................................32
Attaching the presser foot holder........................................................................33
Care and solving machine ..................................................................................34
Replacing the upper nife..........................................................................35
Care of the machine .............................................................................36-37
Cover stitch, important notes on sewing .......................................................38-41
2
Contents
3
Principal parts of the machine
1. Upper needle-thread tension
2. Upper needle-thread tension
3. Thread tension/ upper looper thread
4. Thread tension/ lower looper thread
5. Thread tension/ two-thread chainstitch looper/ cover stitch looper
6. Adjusting nob for presser foot pressure
7. Needle holder
8. Standard presser foot
9. Needle plate
10. Adjusting nob for seam width
11. Seam width viewing window
12. Swivel plate
13. Looper disengaging lever
14. Blade guard (for Overedge/ Overloc )
15. Looper cover
16. Presser foot lever
17. Thread chain cutter
12 3 4 5
7
6
16
8
9
10 12
11
13
14
15
17
Principal parts of the machine
4
18. Thread guides
19. Telescoping thread guide
20. Thread spool pin
21. Cone thread adapter
22. Spool disc
23. Thread spool stand
24. Rear thread guides
25. Stitch length adjustment nob
26. Regulator wheel for differential feed
27. Handwheel
28. Electrical power master switch
29. Machine soc et, foot control
18
19
23
20
22
21
24
25
26
27
28 29
Principal parts of the machine
5
30. Upper overedge looper
31. Lower overedge looper
32. Double chainstitch and cover stitch looper
33. Swiveling stitch width latch
34.
35. Threading aid for double chainstitch and cover-stitch looper
36. Knob for lowering the upper nife
37. Fixed lower nife
Movable upper nife
* Pull the cover to the right and open it towards you.
30
3131
3232
33333434
3535
3636 3737
Accessories
6
1. Sewing table (for Coverstitch/ Chainstitch)
2. Thread (5X)
3. Cone holder (5X)
4. Thread nets (5X)
5. Spool cap - large (5X)
6. Pac of needle
7. Thread disc (5X)
8. Waste container
9. Needle threader
10. Needle inserting tool
11. Upper blade
12. Wrench
13. Oil bottle
14. Edge/ Quilting guide
15. Screwdriver
16. Hex Wrench
17. Tweezers
18. Cleaning brush
19. Blade guard
20. Accessory box
21. Soft cover
* In the Accessory Box.
1
2
3
4
5
6
7
8
910 11
12
13
14
15
16
17 18
19
20
21
To remove the waste container, repeat this procedure
in the reverse order.
Waste Container
Insert the upper latch of the waste container into the
upper slot of the looper cover. Apply pressure to the
lower part of the container until the lower latches fic
into place in the lower slots of the looper cover.
Looper Cover
Push the looper cover fully to the right and then
swivel it down.
Looper cover/ Waste container
7
Thread Unreeling Disc
The thread unreeling disc (in the accessory box) is
used for small spools/spools with notched or rough
ends. Place the spool on the spool pin. Place the
thread unreeling disc on top of the spool. Ma e sure
the spool dise is used under the spool.
Thread Net
Synthetic threads generally unwind too quic ly from
the thread spool. Thread nets have been included to
allow easy use of these threads. Pull the thread net
(located in the accessory box) over the spool from
below. Place the spool on the spool holder catching
the bottom of the thread net with the spool pin.
Foam Pads/ Cone Holders
If you are using large cones (5,000 10,000 mm), the
foam pads and the cone holders will be helpful to you.
With synthetic threads, the foam pads catch threads
that have slipped down and help to advance the
thread flawlessly.
Cone holders serve to ensure that large cones are
well positioned.
Telescopic Thread Guide
Pull the telescopic thread guide upwards to its highest
position.
To ensure optimum thread feed, turn the telescopic
parts slowly until you hear the loc ing balls fic into
place.
8
Telescopic thread guide/ Foam pads/ Cone holders
/ Thread net/ Thread unreeling disc
Indice
Altri manuali Silver Macchina da cucire
