Simpson Eject EMS/First Responder Istruzioni originali

Bladder Connector Eject® Insertion Tool

Eject® CO2

Cartridge

Eject® CO2 Inﬂ ator

Eject® Bulb

I n ﬂ a t o r

Eject® Bladder

Eject®

Practice Bladder

EMS/First Responder

Helmet Removal System

Instructions and Safety Information

See reverse side of this sheet for

EMS helmet removal instructions.

To Prepare the CO2 Inﬂ ator:

Use only Simpson Eject 16g non-threaded

CO2 cartridges, other cartridges may not ﬁ t

properly.

Make sure the red safety lever is in the down

position.

1. Unscrew inﬂ ator head from cartridge cup.

2. Shake cartridge.

3. Insert a NON-THREADED CO2 cartridge

into the cup so the narrow end faces up.

Thread inﬂ ator head onto the cup, turning in

until the cartridge just contacts the puncture

pin, then quickly and ﬁ rmly twist to puncture

(activate) and seal the CO2 cartridge.

Inﬂ ator is now charged and ready for use.

Eject® Helmet Removal System

CO2 Inﬂ ator and Cartridge Operating Instructions:

Figure A.

Step 1.

Step 2.

Step 3.

Do not inhale CO2 gas. Do not

discharge CO2 gas towards face,

body, or people. CO2 gas becomes

extremely cold when dispensed and

should not be exposed to bare skin

as frostbite may occur.

• DO NOT modify the Eject® Helmet

Removal System in any way.

Modiﬁ cations may affect the

proper function.

• Never use any device not approved

by Simpson for inﬂ ation. This

can result in injury to the rider/driver.

WARNING: You must completely understand

all Eject® Helmet Removal System User

Instructions and safety information before

using this product.

Safety Lock Feature:

Do not activate a CO2 cartridge until ready

to use.

Move the red safety lever to the “up” position to

lock the dispensing trigger. (Figure A.) To unlock

the dispensing trigger, move the red safety lever

into the “down” position.

CO2 can ONLY be dispensed when the safety

lock is in the unlocked “down” position.

All CO2 gas must be expelled from used

cartridge before replacement of CO2 cartridge.

Use a new cartridge each time you inﬂ ate an

Eject® unit.

Package may contain any of the following:

Contact Eject® Customer Support

at 1-800-654-7223 or email us at

tex[email protected]om for

more information, training materials

or technical questions.

IMPORTANT

SAFETY INFORMATION

• These instructions are for

Emergency Medical Services (EMS)

to follow when responding

to an accident.

• Simpson recommends that the

Eject® Helmet Removal System be

used ONLY by rescue personnel

trained in spine immobilization

who have complete training on

the system and have read the

full instructions. Proper training

includes practicing before using the

Eject® System on an accident site.

Figure B.

DO NOT inﬂ ate the Eject® system

if there is structural damage to the

top of the helmet.

Determine whether Eject® is

installed in the rider/driver’s

helmet.

Look for “Eject® Equipped” helmet sticker

and connector protruding from base of

helmet. (Figure B.)

This should be located on the left side of

the helmet. Check the inside chin bar area

for sticker if rider/driver is positioned such

that the left side is covered.

YES: Eject® is installed and inﬂ ation

connector was located:

NO: Eject® is not installed or

not accessible:

EMS/First Responder

INSTRUCTIONS

Neither Simpson nor seller shall be liable for damage or injury caused

to yourself, any other person, or any equipment arising out of the

misuse or failure to follow guidelines or instructions for the use of this

product.

TO THE EXTENT CONSISTENT WITH APPLICABLE LAW,

NEITHER SIMPSON NOR SELLER MAKES ANY WARRANTIES

OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR

PURPOSE NOR ANY OTHER EXPRESS OR IMPLIED WARRANTIES.

DISCLAIMER OF WARRANTIES

Figure D.

Figure E.

Figure F.

Figure G.

Figure H.

Figure C.

Figure I. Figure J.

Figure M. Figure N.

WARNING: Check the helmet for structural

damage. Use Eject® with particular care if you

suspect a fracture of the superior portion of

the skull. Remove visible glass or debris from

facial area prior to inﬂ ation of Eject®.

1. Before inﬂ ating the Eject®

Helmet Removal System,

REMOVE OR CUT THE

CHINSTRAP and carefully

remove the patient’s

goggles and or glasses.

(Figure K.)

2. Remove the blue cap on the

Eject® tube connector and

attach the CO2 inﬂ ator (or

the bulb inﬂ ator if the CO2

inﬂ ator is not available).

Unlock red safety lever on

CO2 inﬂ ator or close valve

on bulb inﬂ ator. (Figure L.)

3. Use hands to guide the

helmet, and begin to

inﬂ ate the bladder, (Figure M.) gently guiding

the helmet past the patient’s nose, (Figure N.)

until the helmet has been safely removed.

Look for the Eject® sticker

and tube end connector.

WARNING: Check the

helmet for structural

damage. Use Eject® with

particular care if you

suspect a fracture of

the superior portion of

the skull. Remove visible

glass or debris from facial

area prior to insertion of

First Responder Unit or

inﬂ ation of Eject®.

1. Before inﬂ ating the

Eject® Helmet Removal

System, REMOVE OR

CUT THE CHINSTRAP

and carefully remove the

patient’s goggles and

or glasses. (Figure C.)

2. Place the Eject® EMS/

First Responder unit

on the outside of the

helmet at the top center

point to establish how

far to insert. Estimate

insertion of the bladder

so that the center of the

bag length reaches the

top center of the head.

(Figure D.)

3. Gently take the weight

off the helmet by the chin

guard to create a gap at

the patient’s forehead,

sufﬁ cient to allow the

EMS/First Responder unit

to be inserted. (Figure E.)

4. Push the EMS/First

Responder unit into the

helmet until the bladder

reaches the top center

point of the patient’s

head. (Figure F.)

5. Remove the white

insertion tool by sliding

it out of the helmet.

(Figure G.)

6. Remove the blue cap

on the Eject® tube

connector and attach the

CO2 inﬂ ator (or the bulb

inﬂ ator if the CO2 inﬂ ator

is not available). Unlock

red safety lever on CO2

inﬂ ator or close valve on

bulb inﬂ ator. (Figure H.)

7. Use hands to guide the

helmet, and begin to

inﬂ ate the bladder,

(Figure I.) gently guiding

the helmet past the

patient’s nose, (Figure J.)

until the helmet has

been safely removed.

DO NOT use any device other

than the Eject® Insertion Tool

to insert the Eject® Bladder.

DANGER: Keep the airway clear and maintain cervical spine stabilization

at all times during helmet removal.

Figure K.

Figure L.

Altri manuali Simpson Accessori per motociclette

Simpson

Simpson Eject Helmet Removal System Istruzioni originali

Manuali Accessori per motociclette popolari di altre marche

SRC

SRC B-TRK502-01-01-SL Manuale utente

3M Speedglas 9100 MP Manuale utente

hepco & becker

hepco & becker 6307520 00 01 Manuale utente

HOMCOM

HOMCOM AA0-077 Manuale utente

hepco & becker

hepco & becker 6307558 00 01 Manuale utente

Wunderkind Custom

Wunderkind Custom 106503-F15 Guida utente

Dräger

Dräger HPS 3500 Manuale utente

M-WAVE

M-WAVE SKI Manuale utente

Kuryakyn

Kuryakyn 6212 Manuale utente

hepco & becker

hepco & becker 6507504 00 01 Manuale utente

Tool it

Tool it PROMAX LCD 9.13G Manuale utente

Custom Dynamics

Custom Dynamics TruWrapz Manuale utente

Roof

Roof RO200 CARBON Manuale utente

Kabuto

Kabuto Japan IBUKI Manuale utente

PUIG

PUIG 5051 Manuale utente

rizoma

rizoma ZTH050 Manuale utente

Joubert

Joubert 10001711 Manuale utente

Sperian

Sperian Optrel p420 Manuale utente