Sinoboom GTJZ0407SE Manuale utente

0800 222 111 [email protected]

021 500 486 www.elevatedaccess.co.nz

GTJZ0407SE

Operation Manual

Product specifications

Specifications Unit GTJZ0407SE

Dimensions

Overall length m 1.42

Overall width m 0.76

Overall height m 1.97

Ground clearance mm 65

Ground clearance(Pothole

protection device expanded)

mm 15

Overall weight kg 880

Parameter

Max. platform heightm3.8

Max. working heightm5.8

Extension outreach m0.6

Load capacity kg 240

Extended platform bearing capacity kg 100

Wheel base m1.11

Wheel track m0.68

Turning radius

Inside m0.3

Outsidem1.35

Manual force(indoor) N400

Voltage(DC) V24

Platform size

Length m1.34

Width m0.7

Tire

Dimension mm 230

Width mm 80

Hydraulic volume

Hydraulic tank volume L4

Hydraulic system volume L 5（with tank）

Hydraulic system pressure bar 180

Voltage(DC) V 24

Sound pressure level dB 72

Driving Speed

Stowed km/h 0～4

Raised km/h 0～0.5

Grade ability % 25

Lift/Down speed s 30/25(idling)

Max. allowable wind speed m/s 0

Max. allowable slope

Front and rear 3°

Left and right 1.5°

Illustration

1 Door of Platform

Wires

Socket (optional)

8 Extension Platform Pedal

14 Ground Controller

15 Rear Wheel

17 Ladder/ Fastening Part for

Transportation

18 Emergency Descent Handle

19 Power off switch

20 Battery Charger

21 Charging plug

22 Fastren part of

transportation

Guardrail of Platform

Fastening Point for Lacing

Platform Controller

Tool Box (optional)

Extension Platforms

Platform AC Power

Safety rod (Middle forks)

Level Switch

Warning lamp

Steering Wheel

Pothole Protection Devices.

Fastening Part for

Transportation/Forklift Position

Safety Regulations

Danger

Failure to obey the instructions and safety regulations in this manual will

result in death or serious injury.

No operation unless:

You have fully understood and implemented the safe operation rules specified in this manual.

1 Avoid dangerous situation occurred.

Read and understand the rules above before going to the next steps.

2 Always carry out pre-operation inspection.

3 Always do function test before operation.

4 Inspect workplace.

5 Only use the machine as per its design intention.

You shall read, understand and obey the instructions specified by the manufacturer, safety

manual, operation manual and labels on the machine.

You shall read, understand and obey the instructions specified by the manufacturer, safety

manual, operation manual and labels on the machine.

You shall read, understand and obey the instructions specified by the manufacturer, safety

manual, operation manual and labels on the machine.

You have received proper training on safe operation of the machine.

Label Definition

SINOBOOM labels, color codes and symbols indicate the following:

Safety warning symbol—to indicate potential body injury. All safety tips after this

label shall be obeyed to prevent possible injury or death.

Red—to indicate imminent danger which may result in death or bad injury if

not avoided.

Orange—to indicate potential danger which may result in death or bad injury

if not avoided.

Yellow with safety warning symbol—to indicate potential danger which

may result in minor or moderate body injury if not avoided.

Yellow without safety warning symbol—to indicate potential danger which

may result in property loss.

Green—to indicate operation or maintenance instruction.

Electrocution Hazard

This machine is NOT insulated, and NO electrocution protection is available.

Keep away from the power lines and machines according to applicable government regulations

and the instruction below.

Voltage Min. safety distance

(phase to phase) (m)

0V to 50kV 3.05 m

50kV to 200 kV 4.60 m

200kV to 350 kV 6.10 m

350 kV to 500 kV 7.62 m

500 kV to 750 kV 10.67 m

750 kV to 1000 kV 13.72 m

Caution against strong and fitful wind given the possibility of movement of platform, and

swinging and loosening of cables. No operation during lightning and rainstorm.

Keep away from the machine being connected with live cables. No touch by persons on the

ground and NO operation by persons on the platform before the power is cut off.

NO use of the machine as grounding wire during welding.

Tip-over Hazard

No overload on the platform is allowed.

GTJZ0407SE

Max. Load of platform

Retracting 240kg

Extending—extension only 100kg

The machine can only be lifted or extended when the machine is on solid and level ground.

Do NOT take tilt alarm as level indicator. The tilt alarm on platform works only when the machine

is seriously tilted.

Once the tile alarm rings:

Lower down the platform. Move the machine to solid and level ground. Carefully lower down the

platform if tilt alarm rings during platform lifting. No changes to limit switch is allowed.

Travel speed should be controlled within 0.5m/h during platform lifting.

When the platform is lifted, do NOT drive on or near slope or unstable ground or under other

dangerous conditions.

No operation in strong or fitful wind. Do NOT increase the surface area of platform or loads

exposed in the wind; otherwise it will reduce the stability of the machine.

When platform is stowed, the machine shall be driven extremely carefully at low speed on uneven

area, steep slope, gravel road, slippery ground and places near cave.

Do not drive the machine on the ramp that exceeds the maximum climbing capacity of the

machine .The maximum climbing ability is applicable to the machine in the receiving state.

Changes to the limit switch is forbidden.

Do NOT push or pull any objects outside the platform.

Max Lateral force allowed

Indoor 400N

Do NOT change, or limit the use of any components which may influence

the safety and stability.

Do NOT use components of different weight and specifications to replace components key to

stability of the machine.

Do NOT modify or amend the aerial work platform without written permission from the

manufacturer. Additional devices installed on the platform and guardrails to keep tools and other

materials will increase the weight and surface area of platform, thus increase load.

Do NOT lay or tie some overhung loads on any parts of the machine.

Do NOT place ladders or scaffoldings inside the platform, or against any parts of the machine.

Do NOT use the machine on any moving objects. Make sure that all tires are in good condition

and slotted bolts are properly screwed.

Do NOT use batteries lighter than the original ones. Battery works as counterweight also, it is

critical to the stability of machine. The weight of each battery should be no less than 33kg.

Do Not use the machine as crane.

Do Not use the platform to push machines or any other objects.

Keep the platform from touching anything nearby.

Do NOT tie the platform to any objects nearby.

Keep loads within the platform.

No operation with chassis frame opened.

Do not use platform controller to release platform when it is stuck, stumbled, or blocked by

anything nearby. In this case, use of ground controller only when there are NO person on platform.

Falling Hazard

Everyone on platform shall wear safety belt or use other

security devices in accordance with governmental regulations.

Lacing wires shall be tied to some fastening points on the

platform.

Do NOT sit or stand on or climb the guardrails on the platform. Person in the platform shall

always stand steadily on the bottom plate.

When lifting the platform:

Do NOT climb down the platform or boom.

Keep NO obstruction on the bottom plate of the platform.

Lay down the mid-rail of the platform guardrails or lock the access before operation.

Crush Hazard

Pay attention to objects outside the view during operation.

Pay attention to the extension platform when moving the machine.

Inspect the working area to clear obstructions and other possible hazard overhead.

Beware of the danger of being squeezed when gripping the guardrails of the platform.

Pay attention to and follow the red and yellow arrows indicating driving and steering directions on

the control panel of the platform controller and drive chassis.

Operators shall obey workplace rules, governmental regulations and related rules on use of life

security devices,.

Make sure the machine is on level ground or has been locked before releasing brake

Do NOT lower down the platform when there are people or obstruction under it.

Travel speed shall be controlled according to the ground condition, crowdedness, slope of the

ground, people’s location and other possible factors that may cause collision.

Do NOT operate the boom on any crane route unless the crane controller has been locked and/or

measures to prevent any potential collision have been adopted.

No dangerous driving or jesting during operation.

Smashing and Pressing Hazard

Keep hands and arms away from places where injuries may be caused.

Do NOT operate machine under platform when safety bar is not in proper position.

Use your commonsense judgment when operating the machine on ground with the controller.

Keep proper distance between operator, machine and fixed objects.

Damage Hazard to the Parts

Do NOT use any battery or charger over 24V to start the engine.

Do NOT use the machine as earth wire for welding.

Altri manuali per GTJZ0407SE

Indice

Altri manuali Sinoboom Sistema di sollevamento

Sinoboom

Sinoboom 1323RD Manuale utente

Sinoboom

Sinoboom 1018RD Manuale utente

Sinoboom

Sinoboom GTZZ14EJ Manuale utente

Sinoboom

Sinoboom GTZZ14EJ Manuale utente

Sinoboom

Sinoboom GTJZ0408SE Manuale utente

Sinoboom

Sinoboom GTJZ1023D Manuale utente

Sinoboom

Sinoboom AB10ERJN Manuale utente

Sinoboom

Sinoboom TB24E Plus Manuale utente

Sinoboom

Sinoboom GTJZ0612E Manuale utente

Sinoboom

Sinoboom TB20J Plus Manuale utente

Sinoboom

Sinoboom AB16EJ Plus Manuale utente

Sinoboom

Sinoboom GTJZ2146 Manuale utente

Sinoboom

Sinoboom 1018RE Manuale utente

Sinoboom

Sinoboom GTJZ0608ME Manuale utente

Sinoboom

Sinoboom TB800 Plus Manuale utente

Sinoboom

Sinoboom 1323RD Manuale utente

Sinoboom

Sinoboom TB20J Plus Manuale utente

Sinoboom

Sinoboom GTJZ0608E Manuale utente

Sinoboom

Sinoboom TB28J Plus Manuale utente

Sinoboom

Sinoboom GTJZ0408SE Manuale utente

Sinoboom

Sinoboom TB18 Plus Manuale utente

Sinoboom

Sinoboom GTJZ0408SE Manuale utente

Sinoboom

Sinoboom TB32JN Plus Manuale utente

Sinoboom

Sinoboom TB28J Plus Manuale utente

Manuali Sistema di sollevamento popolari di altre marche

morse

morse 82H-124 Manuale utente

Braun

Braun NL955 Series Manuale utente

haacon

haacon 1889.10 Manuale utente

Protekt

Protekt AT 252 Manuale utente

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Manuale utente

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Manuale utente

Genie

Genie Z-60/34 Manuale utente

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Manuale utente

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Manuale utente

Custom Equipment

Custom Equipment Hy-Brid 3 Series Manuale di programmazione

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Manuale di programmazione

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Manuale di programmazione

BERG

BERG BeNomic EasyLeaf Manuale utente

Powermate

Powermate LiftGate LG-3 Manuale utente

Snorkel

Snorkel TM12 Series Manuale utente

Terberg

Terberg OMNIDEKA Manuale utente

Harmar Mobility

Harmar Mobility AL625 Istruzioni operative

Rotary

Rotary SPO16 Manuale utente