Skytech 1001D-AF1-1 Manuale utente

___________________________________________________________________________________________________________

Rev. 11/8/16 Page 1 of 4

Skytech 1001D-AF1-1

Model: 1001D-AF1-1

INSTALLATION AND OPERATING INSTRUCTIONS

INTRODUCTION

This SKYTECH remote Wireless Wall Switch system was developed to provide safe, reliable, and user-friendly remote

control system for gas heating appliances. The system can be operated manually from the transmitter. The system

operates on one of 65,536 security codes that are programmed into the transmitter at the factory.

WALL TRANSMITTER

The wall transmitter operates on a (2) 3-volt button cell batteries (included) made

specifically for remote controls and electronic lighters. Before using the wall

transmitter, install the two (2) 3-volt button cell batteries. Follow instructions below.

The wall transmitter has an ON/OFF rocker switch. When a rocker switch on the wall

transmitter is pressed, a signal light on the wall transmitter illuminates briefly to verify

that a signal has been sent. If the signal light does not illuminate, check the batteries.

Upon initial use, there may be a delay of five seconds before the remote receiver will

respond to the wall transmitter.

TO INSTALL BATTERIES

1. Remove face from backing plate by insetting a small screwdriver into

the small slot at the top or bottom of the faceplate as shown below then

snap OFF.

2. Locate the (2) holders for the 3V button cell batteries.

3. Place the button cell batteries into the battery holders and snap into

place. (Make sure that the batteries are installed with the (+) plus side as

shown to the right.

4. After the batteries are installed replace the faceplate on the base.

TO REMOVE THE BATTERIES

1. Remove face from backing plate by insetting a small screwdriver into

the small slot on the side at the top or bottom of the faceplate as shown

to the right then snap OFF.

2. Locate the (2) holders for the 3V button cell batteries.

3. Insert a small screwdriver into the slot at the button cell battery and

pop the battery out (Slots shown in picture above).

4. After the batteries are installed replace the faceplate.

IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS DO NOT

ATTEMPT TO INSTALL OR OPERATE

www.FireplaceRemoteControls.com

1.888.977.6849

___________________________________________________________________________________________________________

Rev. 11/8/16 Page 2 of 4

Skytech 1001D-AF1-1

WALL MOUNTING THE TRANSMITTER

1. Remove face from backing plate by insetting a small screwdriver into the

small slot at the top or bottom of the faceplate as shown to the right then snap

OFF.

2. Locate the (2) two mounting holes and mark the holes on the wall. Use the

(2) two dry wall anchors and screws (that are supplied) to mount the base plate

to the wall as shown.

3. The wall transmitter can also be mounted onto an existing (Plastic) electrical

box.

4. Base plate should be mounted level on the wall for best operation.

REMOTE RECEIVER

IMPORTANT

THE REMOTE RECEIVER SHOULD BE POSITIONED WHERE AMBIENT

TEMPERATURES DO NOT EXCEED 130° F.

The remote receiver (right) operates on four 1.5V AA-size batteries. It is

recommended that ALKALINE batteries be used for longer battery life

and maximum microprocessor performance. IMPORTANT: New or fully

charged batteries are essential to proper operation of the remote

receiver as a latching solenoid power consumption is substantially higher

than standard remote control systems.

NOTE: The remote receiver will only respond to the transmitter when the 3-

position slide button on the remote receiver is in the REMOTE position. The

remote receiver houses the microprocessor that responds to commands from

the transmitter to control system operation.

FUNCTIONS:

1. With the slide switch in the REMOTE position, the system will only

operate if the remote receiver receives commands from the

transmitter. Upon initial use or after an extended period of no use,

the ON button may have to be pressed for up to three seconds

before activating solenoid. If the system does not respond to the

transmitter on initial use, see LEARNING TRANSMITTER TO

RECEIVER section.

2. With the slide in the OFF position, the system is off.

3. It is suggested that the slide switch be placed in the OFF position if

you will be away from your home for an extended period of time.

Placing the slide switch in the OFF position also functions as a safety

"lock out" by both turning the system OFF and rendering the

transmitter inoperative.

INSTALLATION INSTRUCTIONS

WARNING

DO NOT CONNECT REMOTE RECEIVER DIRECTLY TO 110-120VAC POWER. THIS WILL BURN OUT

THE RECEIVER. FOLLOW INSTRUCTIONS FROM MANUFACTURER OF GAS VALVE FOR

CORRECT WIRING PROCEDURES. IMPROPER INSTALLATION OF ELECTRIC COMPONENTS CAN

CAUSE DAMAGE TO GAS VALVE AND REMOTE RECEIVER.

INSTALLATION

The remote receiver can be mounted on or near the fireplace hearth. PROTECTION FROM EXTREME HEAT IS VERY IMPORTANT.

Like any piece of electronic equipment, the remote receiver should be kept away from temperatures exceeding 130º F inside the

receiver case. Battery life is also significantly shortened if batteries are exposed to high temperatures.

www.FireplaceRemoteControls.com

1.888.977.6849

___________________________________________________________________________________________________________

Rev. 11/8/16 Page 3 of 4

Skytech 1001D-AF1-1

Make sure the remote receiver switch is in the OFF position. For best results it is recommended that 18 gauge stranded wires should

be used to make connections and no longer than 20-feet.

WIRING INSTRUCTIONS

CONNECTING THE RECEIVER TO A VALVE WITH THE LATCHING SOLENOID

1. Connect the BLACK 18 gage stranded wire with the 1/4’ female terminal from the receiver to the BLACK wire with the

1/4” male terminals from the valve solenoid.

2. Connect the RED 18 gage stranded wire with the 1/4’ female terminal from the receiver to the RED wire with the 1/4”

male terminals from the valve solenoid.

3. After receiver wires are connected to the valve solenoid wire make sure the receiver shield is located over the receiver

and then locate the receiver in an area that will not exceed the 130° F.

IMPORTANT NOTE: Operation of these controls is dependent on which wire is attached to which terminal. If operation

of control does not correspond to operating buttons on transmitter, reverse wire installation at the receiver or at the

control.

NOTE: Up to 6.3 VDC of power is provided at the receiver terminal.

GENERAL INFORMATION

LEARNING TRANSMITTER TO RECEIVER

Each transmitter uses a unique security code. It will be necessary to press the LEARN button on the receiver to accept the

transmitter security code upon initial use, if batteries are replaced, or if a replacement transmitter is purchased from your

dealer or the factory. In order for the receiver to accept the transmitter security code, be sure the slide button on the

receiver is in the REMOTE position; the receiver will not LEARN if the slide switch is in the ON or OFF position. The

LEARN button in located on the front face of the receiver; inside the small hole labeled LEARN. Using a small screwdriver

or end of a paperclip gently press and release the black LEARN button inside the hole. When you release the LEARN

button the receiver will emit an audible “beep”. After the receiver emits the beep press the transmitter ANY button and

release. The receiver will emit several beeps indicating that the transmitter’s code has been accepted into the receiver.

The microprocessor that controls the security code matching procedure is controlled by a timing function. If you are

unsuccessful in matching the security code on the first attempt, wait 1 - 2 minutes before trying again--this delay allows

the microprocessor to reset its timer circuitry--and try up to two or three more times.

OPERATION

4. This remote control will operate the gas valves latching solenoid to open the gas flow to full ON.

5. When the ON button is depressed the transmitter sends a RF signal to the receiver. The receiver then sends a

pulse of 6-volts of power to the solenoid. The solenoid then opens the gas flow to the burner then to full ON.

6. When the OFF button is depressed the transmitter sends a RF signal to the receiver. The receiver then sends a

pulse of 6-volts of power to the solenoid. The solenoid then closes the gas flow to the burner then to full OFF.

7. The remote control will only work with the hand held transmitter. The receiver slide switch is only for positive OFF or

REMOTE operation.

www.FireplaceRemoteControls.com

1.888.977.6849

___________________________________________________________________________________________________________

Rev. 11/8/16 Page 4 of 4

Skytech 1001D-AF1-1

NOTE: Extensive use of the Latching Solenoid (ON/OFF) will reduce the receiver's battery life significantly.

BATTERY LIFE

Life expectancy of the alkaline batteries in the 1001D-AF1-1 can be up to 12 months depending on use of the solenoid

function. Replace all batteries annually. When the transmitter no longer operates the remote receiver from a distance it

did previously (i.e., the transmitter's range has decreased) or the remote receiver does not function at all, the batteries

should be checked. It is important that the remote receiver batteries are fully charged, providing combined output voltage

of at least 5.0 volts. The transmitter should operate with as little as 2.4 volts battery power. NOTE: Extensive use of the

Solenoid will reduce the receiver's battery life significantly.

TROUBLE SHOOTING

If you encounter problems with your fireplace system, the problem may be with the fireplace itself or it could be with the

1001D-AF1 remote system. Review the fireplace manufacturer's operation manual to make sure all connections are

properly made. Then check the operation of the remote in the following manner:

1. Make sure the batteries are correctly installed in the RECEIVER. One reversed battery will keep receiver from

operating properly.

2. Check battery in TRANSMITTER to ensure contacts are touching (+) and (-) ends of battery. Bend metal contacts in

for tighter fit.

3. Be sure RECEIVER and TRANSMITTER is within 20 to 25-foot operating range.

4. Keep RECEIVER from temperatures exceeding 120° F. Battery life shortened when ambient temperatures are above

115° F.

5. If RECEIVER is installed in tightly enclosed metal surround, the operating distance will be shortened.

NOTE:

1. Heat conditions can cause batteries to discharge when temperatures exceed 1150° F. Studies show that alkaline

batteries, when exposed to a constant temperature of 1200° F, can lose up to 50% of their operating power. When

the battery cools down, it will partially recharge itself, but constant heating and cooling will reduce the battery’s normal

life expectancy.

2. Clear Codes: Memory in the receiver might be full if the learn button is pressed too many times. If this happens it will

not allow any more codes to be learned and no audible beep will be heard. To clear memory, place the receiver slide

switch into the REMOTE position. Press the learn button and release after 10 seconds. You should hear three (3)

long audible beeps indicating all codes have cleared. You can now “learn” the transmitter to the receiver as described

in the General Information Section.

SPECIFICATIONS

BATTERIES: Transmitter 12V - (A23) Remote Receiver 6V - 4 ea. AA 1.5 Alkaline

CC ID No.'s: Transmitter - K9L1001DA; Receiver - K9L330IRX

Operating Frequency: 303.8 MHZ

Canadian ISC ID No.'s: Transmitter – 2439 A-1001DA; Receiver – 2439A 3301RX

FOR TECHNICAL SERVICE, CALL: U. S. INQUIRIES CANADIAN INQUIRIES

(855) 498-8324 or (260) 459-1703 (877) 472-3923

For Sales: (888) 672-8929

WEBSITE: skytechpg.com

MANUFACTURED EXCLUSIVELY FOR SKYTECH II, Inc

FCC REQUIREMENTS

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY

UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S

AUTHORITY TO OPERATE THE EQUIPMENT.

www.FireplaceRemoteControls.com

1.888.977.6849

Indice

Altri manuali Skytech Interruttore

Skytech

Skytech RCAF-LMF-WWS Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente