Smart-M HDMV-16x Manuale utente
HDMV-16x
16-Port Full HD Multi-Viewer
View up to sixteen different HDMI video sources
simultaneously on one screen.
Installation
Manual
Made in U.S.A
www.smartavi.com
1-800-AVI-2131
Version 1.3 www.smartavi.com
2
Table 1: Table Of Contents
TECHNICAL SPECIFICATIONS 3
INTRODUCTION AND FEATURES 4
PANEL LAYOUT 4-5
CONNECTING THE BOX 5
MODES 6
FRONT PANEL CONTROL 6-7
TCP/IP Control 7-11
KVM OPERATION 12-13
RS-232 OPERATION 13-14
CONSOLE COMMANDS 14
NAVIGATING THE OSD 14-15
ACCESSORIES 15
FIRMWARE UPGRADE A
Table 2: What's in the Box?
RT NO.
QTY
DESCRIPTION
HDMV-16X(+)
1
16-Port HDMI, Multi-viewer Switch with 16x/9x/Dual/Quad/Full
modes
Power Cord
1
6 ft. Power Cable
CBLDB906
1
6 ft. DB9 Serial RS-232 Cable
Figure 1: HDMV 16x+
Version 1.3 www.smartavi.com
3
Table 3: Technical Specifications
VIDEO
Video Bandwidth Single-link 340MHz [10.2Gbps]
Resolution HDTV 480i,480p,720i,720p,1080i,1080p
PC Resolution 800 x 600 up to 1920 x 1200
Input Video Signal
1.2 volts
Input DDC Signal
5 volts
Single Link Range 1080p
Format
HDMI 1.4
DVI Compliance
Single-link DVI-D 2.0
Output Cable Length Up to 20 ft.
HDCP Compliance 1.0/2.0
Video Bandwidth
Single-link 340MHz [10.2Gbps]
Input Interface
(16) HDMI
Output Interface
HDMI
Connector
Type A [19-pin female]
CONTROL
Front Panel
Tact Switches
RS-232
DB9 (female)
KVM
USB-connected keyboard
TCP-IP
LAN accessible website
MECHANICAL
Height
12 in. (6.86 U)
Width
19 in. (431.8 mm.)
Depth
12.125 in. (259 mm.)
Weight
25 lbs. (11.3 kg.)
POWER
Requirements
Internal 100-240 VAC
Power Supply Approvals
UL, CE, CSA, CEC, RoHS
Introduction
Version 1.3 www.smartavi.com
4
The HDMV Multi-viewer Switch allows you to view up to sixteen different high
definition video sources simultaneously on one display device. Connections to video
sources are managed via HDMI connectors. Advanced viewing options include 16x
mode, 9x mode, quad-mode, full-screen mode, and dual-mode mode. Use this
device to simplify management of multiple sources by controlling them all through
a single display using the front panel, RS-232, and either through TCP-IP or the
optional KVM. The HDMV-16x uses TCP-IP control while the HDMV-16x+ has KVM
control.
Features
View up to sixteen computers (16x) on a single monitor at the press of a button
On-screen display (OSD) makes setup and switching easy
Change views by pressing the Control Panel switches, RS-232, USB keyboard, or
through LAN depending on your model
Display each computer with clean and crisp high-resolution video
Supports HD resolutions up to 1920x1080p
Delivers uncompressed digital video with zero signal loss
HDCP and HDMI 1.4 compliant
Supports EDID for total control of compliant displays
Outputs HDMI up to 20 feet
16x-mode splits the screen to show 16 sources on one screen
9x-mode splits the screen to show 9 sources on one screen
Quad-mode splits the screen to show 4 sources on one screen
Dual-mode splits the screen to show 2 sources on one screen
Full-mode displays 1 source in full screen
Panel Layout
Front Panel
Figure 2: Front Panel
1. Control Panel
2.
Status LCD
Version 1.3 www.smartavi.com
5
Rear Panel
Figure 3: Rear Panel of HDMV-16x
1. HDMI inputs
2. TCP/IP Control
3. RS232(1) Control
4. RS232(2) Control
5. Power IN
6. HDMI output
Connecting the Box
The power connection and switch are located at the back of the unit as well as the RS-
232 connection and all HDMI inputs and output. Connect all peripheral devices first and
turn them on before powering on the HDMV.
1
2
1 2
3
4
5
Version 1.3 www.smartavi.com
6
Modes
Using the Front Control Panel
Figure 4: Front Control Panel
To switch display modes, press the “MENU” button, then use the “UP Arrow” button and
the “DOWN Arrow” button to cycle between all the modes. Hit enter on the desired mode.
Refer to Figure 4 above for help.
To switch the source press the “ENTER” button and enter the desired source number (1-
16), then either hit the “SWITCH” button to move to the field or hit the “ENTER” button
to finish and execute.
Full Screen Mode - In the Full Screen mode, one of sixteen video
sources are displayed in full screen size and maximum resolution.
Dual Screen Mode - In the Dual Screen mode, the screen is split into
two fields of equal size with two video sources displayed in each field.
Aspect ratio is maintained in dual screen mode.
Quad Screen Mode - In the Quad Screen mode, the screen is split into
four fields of equal size with four video sources displayed in each field.
16x Mode - In the 16x mode, the screen displays all sources in a four by
four matrix.
9x Mode - In the 9x mode, the screen is split into nine fields of equal
size with nine video sources displayed in each field.
Version 1.3 www.smartavi.com
7
Hit the “ESC” button to escape out of the menu at any time.
The On-Screen-Display can also be accessed by hitting the “ESC” button when not inside
the menu. Refer to the OSD section for more information.
To write EDID, press the button “MENU” then use the “UP” or “DOWN” button to cycle
through the options until “EDID” appears. Hit “ENTER” then select the desired EDID by
hitting 1,2, or 3 on the front control panel. Then select either yes or no by hitting the
“SWITCH” button and confirming with “ENTER”.
TCP-IP Control
Please note that TCP-IP control is only enabled for the HDMV-16x, the HDMV-16x+
offers KVM control instead.
To enable TCP-IP control, connect an ethernet cable to the HDMV’s ethernet port. Refer to
page 5 for port information. By default, the HDMV will connect to the network using
DHCP. If no DHCP server is available, the HDMV will attempt to use the default IP address
of 192.168.0.200. Static IP assignment can be setup later and is detailed in next sections.
The IP address is shown on the bottom of the OSD screen. Refer to the OSD section for
more information. After finding the IP address, enter it in the browser of your choice and
you will see the webpage shown in Figure 5 below:
Figure 5: SmartAVI HDMV Webpage
Hit the “LOG IN” button to get started. When prompted for User ID and Password, enter
the default “admin” user and the default “1234” password. After logging in successfully,
you will be brought to the home screen.
Version 1.3 www.smartavi.com
8
Device Configuration
In Device Configuration, there are three separate configurable sections: EDID
Configuration, Rename Channels, and Device Configuration. This webpage is shown in
Figure 6 and Figure 7. EDID configuration allows setting the EDID to either a local
monitor, CAT-6605 (EDID 1), or FHX2300 (EDID 2). Select the desired EDID configuration
and hit the “Submit” button. The Rename Channels menu allows naming each channel or
input. Rename channels as desired then hit the “Submit” button.
Figure 6: EDID Configuration and Rename Channels
Under Device Configuration, shown in Figure 7, the current firmware version is displayed
as well as the most recent available version. Clicking on a version allows downloading and
installing of new and older versions. Hitting “Reboot” will restart the network card
controller. Hitting on the “Factory default setting” will restore default settings for the
network card controller. Lastly, hitting the “HDMV16 Reset” will reset the HDMV16x.
Version 1.3 www.smartavi.com
9
Figure 7: Device Configuration
Network Configuration
In network configuration, shown in Figure 8, the HDMV can be configured to use DHCP or
a static IP. By default DHCP is enabled. If static IP is desired, switch the setting to static IP
and enter the static IP, the subnet mask, the gateway address, and hit the “Submit”
button.
Figure 8: Network Configuration Webpage
Administration
In Administration, see Figure 9, new users can be added by first hitting the “Add new
user” then typing a new username in the name field and a password in the password
fields. Checking the box under Admin elevates user rights to admin level for that user. Hit
the Save button to create the specified user.
Version 1.3 www.smartavi.com
10
Figure 9: Administration Webpage
Full Mode
In Full Mode menu, the webpage in Figure 10 will appear:
Figure 10: Full Mode Webpage
The drop-down menu will display all the channels available. Select the desired channel, then
hit the “Submit” button. A macro with the selected channel can also be saved for common
configurations. To do so, selected an unused macro from the macro drop-down menu, enter
a new name for the macro, and hit save. To load a macro, select it from the macro drop-
down menu and hit load.
Indice
Altri manuali Smart-M Interruttore
Smart-M
Smart-M SKM-04 Manuale utente
Smart-M
Smart-M DVNET-4Quad Manuale utente
Smart-M
Smart-M UHDN-4P Quad Manuale utente
Smart-M
Smart-M HR4Plus Manuale utente
Smart-M
Smart-M SMTCP-2 Manuale utente
Smart-M
Smart-M DVR16X16 Manuale utente
Smart-M
Smart-M DVNET-4Duo Manuale utente
Smart-M
Smart-M HDN-4P Manuale utente
Smart-M
Smart-M DVNET-16Pro Manuale utente
Smart-M
Smart-M UHDN-4P-QUAD Manuale utente
