SMART SBID 8084i-G4 Manuale utente

1 smarttech.com/kb/170597 1022737 Rev 01

Important

Before you configure your

SMARTBoard® 8084i-G4

interactive flat panel

You need to set the computer (or Microsoft®Lync® appliance) input’s operating mode to “PC” after

you turn on your SMARTBoard® 8084i-G4 interactive flat panel for the first time but before you

configure and use the interactive flat panel.

I M P O R T A N T

If you do not complete this procedure, the following could occur:

lThe interactive flat panel might not display the outer edges of the computer’s display.

lUsers might notice higher than normal video display latency.

To set the computer input’s operating mode to “PC”

1. Turn on the interactive flat panel.

2. If you’re installing the interactive flat panel as part of a SMARTRoomSystem™ for

MicrosoftLync, set the Lync Room Reset option as described in chapter 3 of the

SMARTRoomSystem for MicrosoftLync setup and maintenance guide

(smarttech.com/kb/170450).

3. On the remote control, press INPUT (a), and then press the red button (b),

which is below the BACK button.

The Input Label menu appears.

I M P O R T A N T

Before you configure your SMARTBoard 8084i-G4 interactive flat panel

2 smarttech.com/kb/170597 1022737 Rev 01

4. Using the left and right arrow buttons on the remote control, select the input that the computer is

connected to, and then press OK.

N O T E

If you’re installing the interactive flat panel as part of a SMARTRoomSystem, select

HDMI3/PC.

5. Using the left, right, up and down arrow buttons on the remote control, select PC, and then

pressOK.

6. Press the down arrow on the remote control to select Close, and then press OK.

In the Input List menu, the computer input’s icon indicates that its operating mode is “PC.”

7. Calibrate and orient the interactive flat panel as documented in the SMARTBoard 8000i-G4

interactive flat panel setup and maintenance guide (smarttech.com/kb/170446) or the

SMARTRoomSystem for MicrosoftLync setup and maintenance guide

(smarttech.com/kb/170450).

N O T E

In most situations, the only time you need to make this change is during the initial

configuration of the interactive flat panel. However, if you subsequently complete a

FactoryReset or LyncRoomReset, you need to complete this procedure afterward.

smarttech.com/support

smarttech.com/contactsupport

© 2013SMARTTechnologiesULC. All rights reserved. SMARTBoard, SMARTRoomSystem, smarttech, the SMART logo and all SMART taglines are trademarks or

registered trademarks of SMARTTechnologiesULC in the U.S. and/or other countries. Microsoft and Lync are either registered trademarks or trademarks of Microsoft

Corporation in the U.S. and/or other countries. All other third-party product and company names may be trademarks of their respective owners. Contents are subject to

change without notice. 10/2013.

Indice

Altri manuali SMART Lavagna interattiva

SMART

SMART M680 Manuale utente

SMART

SMART Board 6065 Manuale operativo

SMART

SMART KAPP IQ Manuale utente

SMART

SMART Board 6000 Series Manuale utente

SMART

SMART Board 800 Series Manuale utente

SMART

SMART Board MX Manuale utente

SMART

SMART KAPP-IQ65-V2 Manuale utente

SMART

SMART 8084i-G4-SMP Manuale utente

SMART

SMART Podium ID350 Manuale utente

SMART

SMART Room System Manuale operativo

SMART

SMART SMART Board Manuale utente

SMART

SMART SBX880 Manuale utente

SMART

SMART Room System SRS-LYNC-XS Manuale di servizio

SMART

SMART SB880i5-MP Manuale utente

SMART

SMART SMART Board Manuale utente

SMART

SMART Board 600i3 Manuale utente

SMART

SMART KAPP iQ PRO 55 Manuale di servizio

SMART

SMART Board 600 Series Istruzioni operative

SMART

SMART Board 600i3 Manuale utente

SMART

SMART SBID8055i-G5-SMP Manuale di servizio

SMART

SMART 2000i-DVS Manuale utente

SMART

SMART SBX880 Manuale utente

SMART

SMART kapp 84 Manuale utente

SMART

SMART SB880i5 Manuale utente

Manuali Lavagna interattiva popolari di altre marche

HitachiSoft

HitachiSoft StarBoard FX-TRIO-88W Manuale utente

Buhl

Buhl LyteBoard Manuale utente

SMART Board

SMART Board 680 Manuale utente

Legamaster

Legamaster e-SCREEN ETX Manuale utente

SMART Board

SMART Board SBM685ix2 Manuale utente

Seneca

Seneca eno Manuale utente

BenQ

BenQ RP840G Manuale utente

Olivetti

Olivetti OLIBOARD Manuale utente

Turning Technologies

Turning Technologies MOBIVIEW Manuale utente

Panasonic

Panasonic UB-5335 Manuale utente

Dukane

Dukane ITP84 Manuale utente

Bretford

Bretford EDUIMS Guida alla configurazione

Panasonic

Panasonic Panaboard UB-5315 Manuale utente

Plus

Plus M-11S Manuale utente

TRIUMPH BOARD

TRIUMPH BOARD ULTRA SLIM Manuale utente

Returnstar Interactive Tech

Returnstar Interactive Tech IQBoard DVT V7.0 Manuale utente

AVer

AVer CP series Manuale utente

Genee

Genee 56" Manuale utente