SMART MN610 Manuale utente

MN610

10 CHANNEL

CINEMA BOOTH

MONITOR

Version A, August 1999.

5945 Peachtree Corners East

Norcross, GA 30071-1337

CONTACT:

SMART Devices Technical Support or Sales Department

8AM and 5PM, E.S.T., Monday - Friday

(800) 45-SMART

(770) 449-6698

(770) 449-6728 (FAX)

Technical Support: [email protected]

International Sales: [email protected]

U.S. Sales: [email protected]

LIMITED WARRANTY: SMART products and accessories are warranted

against malfunction or failure due to defects in workmanship or materials

for a period of one year from the date of shipment. If a problem occurs dur-

ing the warranty period, the unit will be repaired, or replaced at our option,

without charge for materials or labor. If air freight is requested by the

dealer, the difference between air and surface charges will be billed to the

dealer. This limited warranty does not cover products that have been

abused, altered, modified, or operated in other than specified conditions.

Prior factory approval is required on all returns. Returned equipment or de-

fective parts must be shipped freight prepaid to us by the dealer or cus-

tomer.

Our limited warranty does not cover damages resulting from accident, mis-

use or abuse, lack of responsible care, or failures not attributable to manu-

facturing defects, except as provided herein. SMART Devices, Inc. makes

no warranties, express or implied, including warranties of merchantability

or fitness for a particular purpose.

RETURN POLICY: Factory authorization MUST be obtained before return-

ing any product. A 15% restocking charge will be issued on unused equip-

ment (in original box) that is returned for credit. Credit is issued to the

dealers account. The credit may be used against future purchases and no

cash transactions are offered. All returns must be shipped freight prepaid

by the dealer. Equipment returned without a factory RA (Return Authoriza-

tion) will be refused.

MN610

10 Channel Cinema Booth Monitor

USER’S GUIDE

SMART products are designed to deliver unsurpassed quality in workman-

ship and performance. The following information gives detailed instructions

on the installation and operation of the SMART MN610 Cinema Booth

Monitor. We strongly encourage new owners of the MN610 to thoroughly

read this entire manual before placing their new SMART product into ser-

vice. This will ensure that the MN610 will be operated properly to give the

superior performance that it was designed to deliver.

+ONTENTS

INTRODUCTION ............................................. 4

INSTALLATION ............................................... 5

OPERATION .................................................. 8

4 MN610 10 CHANNEL BOOTH MONITOR

INTRODUCTION

The MN610 is a 10 channel booth monitor that monitors both

sound processor and amplifier outputs while incorporating a

number of advanced features:

•10 Channels. The MN610’s 20 inputs are split between

processor and amplifier banks of 10 each. The banks are

selectable using the MODE button located on the front

panel.

•Balanced Inputs. To avoid ground loop hum, the MN610

has balanced inputs on all channels.

•THX Standard DB25 Processor Input. Connecting a

processor with a THX Standard output is quick and easy.

•Biamp/Triamp Monitoring. Both the processor and

amplifier banks provide Biamp and Triamp monitoring for

the Left, Center and Right channels.

•Multiple Channel Monitoring. The multiple pushbutton

interface allows the user to add in all ten channels on either

bank to the output amplifier.

•Multiple Outputs. There are three different ways to

monitor from the built-in 10 Watt Power Amplifier:

1. Built in 3 1/2" speaker.

2. 1/4" phono rear panel external speaker jack.

3. 1/4" front panel headphone jack.

USER’S GUIDE 5

INSTALLATION

1. Mount the MN610 in a convenient 3

1/2" rack space using four rack

bolts. Ideally, the monitor should be

located between the processor and the

amplifiers.

2. Using shielded pair wire, connect

the outputs of the processor to the

appropriate inputs on the monitor.

For balanced outputs, tie the positive

(+) terminal of the processor to the

positive (+) terminal on the monitor,

and tie the negative (-) terminal of the

processor to the negative (-) terminal on the monitor. For

unbalanced outputs, use the ground terminal (GND, E) on

the processor to tie to the negative (-) terminal on the

monitor. Tie the shield of the cable to the ground (GND, E)

at the processor, leaving the shield unconnected at the

monitor. Alternatively, if

the processor

has a THX

Standard output

for monitoring,

connect the

DB25 cable to

the appropriate

jacks on the

processor and

monitor. Do NOT apply signal to both the terminal block

and DB25 connector inputs for the same signal. LEFT

REAR, RIGHT REAR, and any MID or HI frequency terminal

block inputs may be safely used in conjunction with the

DB25 connector.

6 MN610 10 CHANNEL BOOTH MONITOR

3. Using unshielded pair

wire, connect the

outputs of the

amplifier to the

appropriate inputs on

the monitor. As with a

balanced processor, tie

the positive (+) terminal

of the amplifier to the

positive (+) terminal of

the monitor. Tie the

negative (-) terminal of

the amplifier to the

negative (-) terminal of

the monitor.

Single Frequency

Band Monitoring. For

single frequency Left,

Center and Right

channels, use the corresponding “Lo” inputs.

Split Frequency Band (Biamp, Triamp) Monitoring.

For Biamped Left, Center and Right channels, use the “Lo”

inputs for the low frequency band, and the “Hi” Inputs for the

higher frequency band. For Triamped Left, Center, and

Right channels, use the “Lo” for low, “Mid” for middle and

“Hi” for high frequency bands.

4. Set the processor and amplifier gain trimpots for the

desired level. After the processor and amplifiers have

been set up and calibrated for optimal presentation,

run pink noise through the processor set at the cal

point volume level. Select processor mode and a

channel with pink noise on the monitor. Using a

tuning wand or equivalent, adjust the P Gain Trimpot

(located on the front of the monitor unit) until the third

THX Standard DB25 Pinouts

Signal Pin

Left + 2

Left - 14

Center + 5

Center - 17

Right + 8

Right - 20

Left Wall + 23

Left Wall - 10

Right Wall + 24

Right Wall - 11

SubWoofer + 25

SubWoofer - 12

Left Extra + 16

Left Extra - 3

Right Extra + 19

Right Extra - 6

USER’S GUIDE 7

Signal Presence LED just comes on. Change to amplifier

mode on the monitor, and repeat using the A Gain Trimpot.

The monitor volume knob may be turned down during this

adjustment. If the monitor sound level is not high enough,

these pots may be adjusted clockwise for additional gain.

5. Add an external speaker (

optional

). The MN610

provides a 1/4"/6.3mm

external speaker jack on

the rear of the unit. Wire a

4 or 8 ohm speaker to a

mono 1/4" phono jack and

insert in the jack labeled

EXTERNAL SPEAKER.

When the external speaker

jack is used, the built-in

speaker is disconnected.

8 MN610 10 CHANNEL BOOTH MONITOR

OPERATION

Power is applied to the unit when the red

POWER LED on the front panel is lit. The 1/

4” mono HEADPHONE jack allows for better

listening in a noisy booth environment. It is

wired in parallel with the internal/external

speaker outputs. The main VOLUME knob

controls the volume for all outputs.

The SIGNAL LEVEL LEDs indicate the

relative amplitude of monitored signals.

The levels displayed are not calibrated

to any standard audio measurement.

The level indicated is also not affected

by the output level set by the VOLUME

knob.

The MODE switch selects either the processor or amplifier

bank of inputs for monitoring.

Pushing a switch to the “in”

position adds the corresponding

channel to the monitoring mix.

Note: Since monitoring more

than one channel “adds”the

channels together before the

final amplification, monitoring

many channels at once may cause overload distortion.

While this is not dangerous to the monitor, it will not

accurately represent the sound quality of the system.

Indice

Altri manuali SMART Monitor

SMART

SMART MN600 Cinema STEREOCHECK Manuale utente

SMART

SMART 6000S Series Manuale del prodotto

SMART

SMART MX Series Manuale utente

SMART

SMART Board 6000 Series Manuale utente

SMART

SMART MX Series Manuale utente

SMART

SMART SMART Board Manuale utente

SMART

SMART SBID-7275 Manuale utente

SMART

SMART SBID-MX165 Manuale utente

SMART

SMART 6000S Series Manuale utente

SMART

SMART Podium ID422w Manuale utente

SMART

SMART Board MX V2 Series Manuale utente

SMART

SMART Podium 624 Manuale utente

SMART

SMART 6000 Pro Series Manuale utente

SMART

SMART KAPPIQ-75 Manuale utente

SMART

SMART MX Series Manuale utente

SMART

SMART 6000S Series Manuale utente

SMART

SMART Rear Projection SMART Board 1800 Manuale utente

SMART

SMART SPNL-6055 Manuale del prodotto

SMART

SMART Sympodium IC-150 Manuale utente

SMART

SMART Podium SP518-NB Manuale utente

SMART

SMART 7086 Manuale utente

SMART

SMART SBID-6065 Manuale utente

SMART

SMART CORDLESS TL-2100G Manuale operativo e di manutenzione

SMART

SMART MX Series Manuale di istruzioni

Manuali Monitor popolari di altre marche

Linear Acoustic

Linear Acoustic LQ-1000 Manuale utente

AOC

AOC I2579V Manuale utente

Gateway

Gateway FPD1520 Manuale utente

Furuno

Furuno Mu 120c Manuale utente

Asus

Asus VB171D - 17" LCD Monitor Manuale utente

Dell

Dell S2230MX Istruzioni utente

Philips

Philips 107C64 Manuale utente

Dell

Dell S2409WFP Manuale utente

EverFocus

EverFocus EN-7517E Manuale utente

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuale utente

Dell

Dell Precision 7680 Manuale di istruzioni

LG 50PM1M - - 50" Plasma Panel Manuale utente

Bosch

Bosch DDU 9 Manuale utente

Acer

Acer A231HL Manuale utente

Philips

Philips 86BDL4152T Manuale utente

NEC

NEC AccuSync LCD5V Manuale utente

Emay

Emay SleepO2 Manuale utente

IBM

IBM 6360 Istruzioni per l'installazione