Smeg WD7015TECO Manuale utente

WD7015TECO

INSTALLATION MANUAL

DOCUMENT FOR THE USE OF AUTHORISED ENGINEERS ONLY

TRANSLATION OF THE ORIGINAL INSTRUCTIONS

WD7015TECO –ECO HEAT EXCHANGER INSTALLATION INSTRUCTIONS

195610203.00

2 / 11

READ CAREFULLY

This document relates to Smeg “WD7015TECO” products.

With these specific models, some components are supplied disassembled from the product and packaged separately;

they have to be fitted on site by authorised technical staff.

This document provides detailed instructions for installation of the “Eco” Heat Exchanger used on this product and

the checks which follow.

The document is addressed to authorised engineers and must be used jointly with the user manual and the

Installation Requirements document.

Installation, maintenance and any repairs may only be carried out by personnel authorised by

the manufacturer.

Failure to read, any misunderstanding or incorrect interpretation of the instructions provided in this manual may lead

to misuse of the device, put the operator at risk and considerably impair the device’s performance.

The information in this manual is provided for guidance only. The contents and the equipment described may be

subject to change without notice.

195610203.00

01/03/2023

First issue

Code and Rev.

Date

Notes

TABLE OF CONTENTS

1Introduction –WD7015TECO.....................................................................................................................................3

2Dimensions.................................................................................................................................................................3

3Assembly instructions ................................................................................................................................................5

3.1 Full list of components for assembly.................................................................................................................5

3.2 Precautions in preparation for installation .......................................................................................................6

3.3 Unit assembly procedures.................................................................................................................................7

4Inspecting the unit after assembly...........................................................................................................................11

5Manufacturer and after-sales service contact information.....................................................................................11

WD7015TECO –ECO HEAT EXCHANGER INSTALLATION INSTRUCTIONS

195610203.00

3 / 11

1INTRODUCTION –WD7015TECO

In addition to the demineralised water and hot water heaters, Smeg WD7015 models with suffix “TECO” –

e.g. “WD7015TECO” – are fitted with an additional Heat Exchanger, the “Eco Heat Exchanger”.

The Heat Exchanger, mounted on and fixed to the top of the product, allows hot demineralised water from the final

thermal disinfection rinse to be reused to pre-heat the incoming demineralised water.

This component saves both energy and water.

The Heat Exchanger is only installed on models with suffix “TECO” and cannot be fitted on other models.

Devices undergo complete testing in the factory, but the Heat Exchanger is disassembled and packaged separately for

easier transportation.

Technical staff are required to:

1. assemble the Heat Exchanger;

2. make its water and electricity connections;

3. check that it has been assembled correctly, especially with the regard to the tightness of all connections, and

test its operation.

See www.smegtech.com for the product’s up-to-date functional and wiring diagrams, for full information about

WD7015TECO models.

2DIMENSIONS

The overall dimensions of the Heat Exchanger are:

-Width: 870 mm

-Depth: 820 mm

-Height: 225 mm

Weight of the Eco Heat Exchanger, which has to be lifted and placed on top of the device: 35 kg.

Refer to the latest edition of the “Installation Requirements” document for product information and dimensions.

WD7015TECO –ECO HEAT EXCHANGER INSTALLATION INSTRUCTIONS

195610203.00

4 / 11

Fig. 1 –Device overall dimensions.

WD7015TECO –ECO HEAT EXCHANGER INSTALLATION INSTRUCTIONS

195610203.00

5 / 11

3ASSEMBLY INSTRUCTIONS

3.1 FULL LIST OF COMPONENTS FOR ASSEMBLY

Fig. 2 –Blow-up diagram of components for assembly.

COMPONENT DESCRIPTION

QUANTITY

Eco Heat Exchanger

Side casings

Front and rear casings

Self-tapping screws

M5 nuts

Various hose clamps

Fig. 3 –Heat exchanger position at end of assembly procedure.

D x 8

E x 4

WD7015TECO –ECO HEAT EXCHANGER INSTALLATION INSTRUCTIONS

195610203.00

6 / 11

3.2 PRECAUTIONS IN PREPARATION FOR INSTALLATION

ATTENTION

Before installing the components:

1. Check that the device is not connected to the electricity supply.

2. If its electrical connection has already been made: disconnect the power supply using the

main switch on the switchboard.

3. Turn off the water supply taps if already connected.

4. Turn off any other utility supplies and connections (e.g. steam system if installed).

Check that all precautions necessary for safe operation have been taken, ensuring in particular

that components are not electrically live.

CLEARANCE: A clearance of about 1 m2is required at the front of the device and on both sides to

allow correct operation.

PROTECTIVE EQUIPMENT: Wear gloves as protective equipment to prevent cuts from sharp edges

on metal pieces and casings.

The Eco Heat Exchanger must be placed on top of the device: proceed with all necessary

precautions, using ladders and at least 2 operatives to place the unit in the required position.

WD7015TECO –ECO HEAT EXCHANGER INSTALLATION INSTRUCTIONS

195610203.00

7 / 11

3.3 UNIT ASSEMBLY PROCEDURES

Illustration

Description

Step 1

First remove both the device’s side panels for

access to the hoses for connection to the Eco

Heat Exchanger.

Step 2

Place the Heat Exchanger unit on top of the

device as shown on the left.

The device is prefitted with the hoses for

connection to the Heat Exchanger; fit them on

the outside of the unit, so that:

1. the ends of the hose are accessible for

connection after the Heat Exchanger

is in place.

2. The hoses are not crushed

underneath the unit.

Take special care that the Heat Exchanger’s

connection fittings are facing towards the

unloading side of the device, as shown.

Step 3

Loosely fit the nuts provided on the M5 pins on

the top of the device, to hold the unit in

position.

Unloading side

Loading side

WD7015TECO –ECO HEAT EXCHANGER INSTALLATION INSTRUCTIONS

195610203.00

8 / 11

Illustration

Description

Step 4

The first two water connections to be made are

those to the internal coil of the Heat Exchanger

(marked IN and OUT).

Connect:

1. First, the Heat Exchanger outlet pipe

“OUT” to the “OUT” connection on

the top of the device.

2. Second, connect the coil inlet pipe

“IN”.

3. Secure both of them firmly with the

clamps.

Step 5

Secure the flexible steel pipe to the connection

on the top of the tank (connection marked:

“IN_RWT”).

A 29 mm spanner is required.

A gasket is placed between the fittings to

ensure tightness: check that the gasket is

present and in good condition before

tightening the connection.

Take special care to ensure that the

connection is made properly: the pipe carries

high temperature water from the thermal

disinfection phases.

OUT

IN_RWT

WD7015TECO –ECO HEAT EXCHANGER INSTALLATION INSTRUCTIONS

195610203.00

9 / 11

Illustration

Description

Step 6

Connect the outlet fitting of the Heat

Exchanger which leads to the washing

chamber: “OUT_SOL_RU” connection.

Secure it with the clamp provided.

[“SOL_RU” is the solenoid valve which allows

the Heat Exchanger to discharge into the

washing chamber.]

Step 7

Connection of the overflow “OVER_RWT”.

Connect the overflow hose in the bottom of the

Heat Exchanger and secure it with the clamp

provided.

Step 8

The bottom of the Heat Exchanger unit

includes a drip tray to catch any leaks from the

connections.

There is a drain fitting underneath the drip

tray, which must be connected to the drain

pipe provided.

“OUT_DRIP_TRAY” connection

Secure the connection with the clamp

provided.

chamber inlet

OUT_SOL_RU

Overflow

OVER_RWT

WD7015TECO –ECO HEAT EXCHANGER INSTALLATION INSTRUCTIONS

195610203.00

10 / 11

Illustration

Description

Step 9

Connect the top vent pipe VENT_RWT

Step 10

The only electromechanical component on the

unit is the level sensor “SLRU_MIN”.

Make the electrical connection to the sensor

using the connectors provided.

Step 11

Securely tighten the unit’s 4 fixing bolts.

Step 12

Fit the external casings and secure them with

the screws provided.

Indice

Manuali Asciugatrice popolari di altre marche

Bosch

Bosch WTA79200GB Manuale utente

Amana

Amana W10233410A Manuale utente

Miele

Miele TWH 780 WP Manuale utente

Asko

Asko T760 Manuale utente

Alliance Laundry Systems

Alliance Laundry Systems 25 Series Manuale utente

Bosch

Bosch Logixx 10 WTB76556GB Scheda tecnica

STIEBEL ELTRON

STIEBEL ELTRON Ultronic S Manuale di istruzioni

Electrolux

Electrolux EW2H328R2 Manuale utente

Beko

Beko DS8433RX1M Manuale utente

Dawlance

Dawlance Spinner DS 6000 C Manuale utente

Electrolux

Electrolux TP5080TW Manuale utente

AEG

AEG TR838P4OB Manuale utente

Indesit

Indesit IDV 75 Manuale utente

Infiniton

Infiniton SD-DG85C Manuale utente

BOMANN

BOMANN WT 5019 Manuale utente

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Manuale utente

Asko

Asko T793C Manuale utente

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Manuale utente