Snapper 1685336 Manuale utente

GENERAL

The Spring Assist Kit is used to retrofit the hitch used to

install the 42” and 46” Snow Plow/Dozer Blade on

several different models (series) of tractors. For easier

understanding of this instruction sheet, first identify the

size of blade (42” or 46”) and group of tractor on which

you are working. Follow these specifications throughout

the ten steps.

Tractors:

Group 1: 600,4000,5000

Group 2: 800,600O

Group 3: 700,700O

Group 4: 900, 7100

Snow Plow/Dozer Blade:

42”

Mfg. No. 1690085 (Group 1, 2 tractors)

42”

Mfg. No. 1691520 (Group 3, 4 tractors)

46”

Mfg. No. 1~690088 (Group 3, 4 tractors)

IT PARTS

Mounting location for 42” blade on Group 2 tractors

Use 0, 1, 2 or 4 links

Mounting location for 42” Group 1, 3 and 4tractors

Mounting location for

46” blade on Group 3

z&d

4 tractors

r,gure

n,r

I-aITs

Ref. Description Gty.

Part Number

A. NUT, Hex Lock,

5/l&18

1923362

WASHER, Plain,

5/16

2 1919381

CAPSCREW,5/16-18x1-1/4

1921977

D. CHAIN, 4-Links

1669241

SPRING

1675232

INSTALLATION

INSTRUCTIONS

SPRING ASSIST KIT

MFG. NO. 1685336

INSTALLATION

1. Park tractor on a flat, level surface. Shut off engine,

remove key and apply parking brake.

2. Release lift handle so that dozer blade rests on the

ground.

3. Remove spring clip from king pin (A, figure 2).

Remove king pin and pivot pin (B) from push bar.

Slide dozer blade forward and

remcwe

from push

bar.

4. Remove cotter pin (C) from rod guide(D). Remove

rod guide from hitch bracket

(E).

Push bar should

now be free to move up and down.

Figure 2. Dozer Blade Removal

A. King Pin

B. Pivot

C. Cotter Pin

D. Rod Guide

E. Hitch Bracket

5. Drill a hole in the bottom cross member (42” blade

on Group 1, 3 and 4 Series tractors) or

upper cross member (42” blade on Group 2 tractors)

according to the diagrams of the templates in figure

3. Actual templates are on a separate insert included

with these instructions.

For 46” blades on Group 3 and 4 tractors, drill a

,406”

hole in the (top) front plate. Hole should be located

2-3/4” left of centerline and 1/2”forward of the plate

rear edge. (Refer to figures 7E

+7F.)

FcmM

1701916

PRlNTED

IN U.S.A.

878

Figure 3. Diagrams of Hitch Templates

6. Assemble the chain (D, figure 1) to the tractor as

follows:

42”

Blade on Group 1 and 2

On left-hand side, remove and discard the upper

self-tapping screws that holds bumper to frame.

This is the hole used for installing chain in the

following steps, using 5/ 16-18 x

l-1/4

capscrew

(C), two 5/ 16 washers (B) and one 5/ 16 locknut

(A).

Place one 5/ 16 washer onto the

capscrew.

Then

place the chain on the capscrew, and then the

other 5/ 16 washer:

Insert the capscrew (A, figure 4) through tractor

frame. From inside the frame, install 5/ 16 locknut

onto capscrew. Tighten snug only at this time.

(Spring (B) will be installed in step 7.)

Figure 4. Chain Installation (Group 2 Tractor

Shown)

Capscrew 6.

Spring

42” Blade on Group 3 and 4; 46” Blade on Group 4

On the left hand side, remove the front hood pivot

bolt.

b. Chain must be installed with the following

hardware (not included in this kit):

Place one washer onto capscrew. Place first link of

chain (42” blade on Group 3 tractor) or second

link of chain (42”/46” blade on Group 4 tractor)

capscrew.~

Install final two washers on

lXp%XWV.

d. Insert capscrew (A, figure 5) through tractor

frame. Tighten snug only at this time. (Spring,(B)

will be installed in step 7.) From inside the frame,’

install locknut.

Figure 5. Chain Installation (Group 3 Tractor

Shown)

Capscrew 6.

Spring

46” Blade on Group 3

a. The chain is not used to secure spring to tractor

frame. Spring is installed directly to

holein

tractor

frame.

b. Drill a

,406

hole in the front of frame l-114” in

from the front left side and

l/2”

up from the

bottom of the frame. Refer to figure 6.

Figure 6. Spring Installation (Group 4 Tractor

Shown)

Blade Tractor Qty Hardware Number

42” Group 3 1

Capscrew,

3/8-16

2-l/4’ 1922130

7. Raise the push bar and hook up one end of spring to

chain or frame as shown in figures 7A through 7F.

Hook other end of spring to hole drilled in hitch cross

member (figure 7A-7D) or top front plate (figure 7E-

_-.

,Wa.sher,

3/6

1622766

42” Group 4

Capscrew,

3/S-16

l-1/2’

1921969

46”

3Washer

1922755

gibe).

.__

Figure 7A. 42” Blade

Group

Figure 76. 42” Blade

Group 2

1Member From Top Down

Figure 7D. 42” Blade

Group 4

Figure 7E. 46” Blade

Group 3

Figure 7C. 42” Blade

Group 3 Figure 7F. 46” glade

Group 4

Figures 7A

thru

7F. Spring Installation

Lower push bar and install dozer blade with kingpin

(A, figure

2),

spring clip, and pivot pin(B). Reattach

rod guide (D) and secure with cotter pin (C).

9. Tighten capscrew (A, figure 4 or 5) and nut which

hold chain to tractor frame.

10.

Perform Lift Rod Adjustment as instructed in

Operator’s Manual for your Snow Plow/Dozer

Blade.

3’.

Upper Cross Member

(42” blade

Group 2)

3/S”

Dia.

Bottom Cross Member

142” Blade on Group 1, 3

Actual Templates of Figure 3.

INSERT

1701016

Altri manuali Snapper Taglia erba

Snapper

Snapper LT300 Series Manuale utente

Snapper

Snapper C21501KWV Manuale operativo e di manutenzione

Snapper

Snapper 281023BVE (84871) Manuale utente

Snapper

Snapper 21” STEEL DECK “M” WALK BEHIND MOWER Set-up Manuale utente

Snapper

Snapper 28587 LT Series Manuale

Snapper

Snapper EFRP216516BV Manuale operativo e di manutenzione

Snapper

Snapper SPX-100 Manuale utente

Snapper

Snapper E251023BVE, E281223BVE, E28132 Manuale operativo e di manutenzione

Snapper

Snapper Lawn Mower Manuale

Snapper

Snapper 214X4PR Manuale operativo e di manutenzione

Snapper

Snapper EMRP215014B Manuale operativo e di manutenzione

Snapper

Snapper R204513E Manuale operativo e di manutenzione

Snapper

Snapper 33115SC Manuale utente

Snapper

Snapper RPX200 Manuale utente

Snapper

Snapper SP360 Manuale operativo e di manutenzione

Snapper

Snapper HZS15423KVE SERIES 3 Manuale operativo e di manutenzione

Snapper

Snapper SPS322T Manuale utente

Snapper

Snapper 7800179 Manuale operativo e di manutenzione

Snapper

Snapper Z-Rider 07224 Manuale utente

Snapper

Snapper YT18H Series 3 Manuale utente

Snapper

Snapper 21" Walk-Behind Lawn Mowers Manuale utente

Snapper

Snapper Z-rider Manuale

Snapper

Snapper 7800842-01 Manuale utente

Snapper

Snapper SERIE 1 CZT19481KWV Guida rapida

Manuali Taglia erba popolari di altre marche

RHINO

RHINO 1958 Manuale utente

Wolf Garten

Wolf Garten Compact plus 40 B Manuale utente

Cub Cadet

Cub Cadet LTX 1045 Manuale utente

Craftsman

Craftsman 917.378461 Manuale utente

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Manuale utente

Challenge

Challenge CH18V2 Istruzioni operative

TALEN TOOLS

TALEN TOOLS AVR HGM30 Manuale utente

DEWEZE

DEWEZE ATM-725 Manuale operativo

Weed Eater

Weed Eater 180083 Manuale utente

Husqvarna

Husqvarna Poulan Pro PP185A42 Manuale utente

Better Outdoor Products

Better Outdoor Products Quick Series Manuale utente

Cub Cadet

Cub Cadet 23HP Z-Force 60 Manuale operativo

MTD

MTD 795, 792, 791, 790 Manuale utente

Toro

Toro Groundsmaster 3505-D Manuale utente

Dennis

Dennis FT 610 Manuale utente

AIRFORCE

AIRFORCE F-15 Gen 3 Manuale utente

MTD

MTD 126-220-000 Manuale utente

Toro

Toro 74806 Manuale utente