SNBC BTP-L580 Manuale utente
USER’S MANUAL
Label Printer
BTP-L580
Shandong New Beiyang Information Technology Co., Ltd.
BTP-L580 User’s Manual
1
Declarations
Information in this document is subject to change without notice.
SHANDONG NEW BEIYANG INFORMATION TECHNOLOGY CO.,
LTD. (hereinafter referred to as “SNBC”) reserves the right to
improve products as new technology, components, software, and
firmware become available. If users need further data about this
product or have any doubt about safety issues that might arise from
using it, please feel free to contact SNBC or your local agents.
Copyright
No part of this document may be reproduced or transmitted in any
form or by any means, electronic or mechanical, for any purpose
without the express written permission of SNBC.
Copyright © 2011 by SNBC
Printed in China
Version 1.0
Trademarks
Our registered trademarks are
Warnings and Cautions in this manual
Warning: Items shall be strictly followed to avoid
damages to body and equipment.
Caution: Items with important information and prompts
for operating the printer.
BTP-L580 User’s Manual
2
The control system of SNBC has been approved of
the following certification:
ISO9001 quality control system certification
ISO14001 environmental control system certification
OHSAS18001 profession health safety control system
certification
IECQ QC080000 hazardous material process control system
certification
BTP-L580 User’s Manual
3
General Safety Instruction
Before installing and using the printer, please read the following
items carefully:
1. Safety Instructions
Caution: Do not touch the cutter of the printer.
Heating: The print head is at a high temperature during
printing or just after operation. Do not touch it
and its peripherals for reasons of safety.
Warning: The print head is an ESD-sensitive device. To
avoid damage, do not touch either its printing
parts or connecting parts.
2. Caution
1) Install the printer on a flat and stable surface.
2) Reserve adequate space around the printer so that convenient
operation and maintenance can be performed.
3) Keep the printer away from water source, direct sunlight, strong
light and heat.
4) Do not use or store the printer in a place exposed to heat or fire,
moisture or other pollution.
5) Do not place the printer in a place exposed to vibration or impact.
6) No dew condensation is allowed to the printer. In case of such
condensation, do not turn on the power until it has completely
gone away.
7) Connect the power cord to an appropriate grounding outlet.
Avoid sharing a single electrical outlet with large power motors
BTP-L580 User’s Manual
4
and other devices that may cause the fluctuation in voltage.
8) Disconnect the power cord if the printer is idle for a long time.
9) Do not spill water or other electric substances (like metal) on the
printer. If this happens, turn off the power immediately.
10) Do not allow the printer to start printing when there is no
recording paper installed, otherwise the print head and platen
roller will be damaged.
11) To ensure quality print and normal lifetime, use recommended or
good quality paper.
12) Shut down the printer when connecting or disconnecting
interface connectors to avoid damage to the control board.
13) Set the print darkness to a lower grade as long as the print
quality is acceptable. This will help to keep the Printhead
durable.
14) The printer should only be disassembled or repaired by a
technician, who is certified by SNBC.
15) Keep this manual safe and at hand for reference purpose.
BTP-L580 User’s Manual
1
Content
1 INTRODUCTION...........................................................................1
1.1 Outline ....................................................................................1
1.2 Main Features.........................................................................1
2 MAIN SPECIFICATION.................................................................2
2.1 Technical Specification............................................................2
2.2 Cutter Specification.................................................................3
2.3 Paper Specification.................................................................3
2.3.1 Thermal Label Paper Parameter......................................3
2.4 Print and tear off position........................................................5
2.4.1 Print position ....................................................................5
2.4.2 Tear off position................................................................6
3 OUTLINE AND PARTS.................................................................7
3.1 Outline and Parts....................................................................7
3.2 Error LED and Buzzers.........................................................10
4 INSTALLATION...........................................................................12
4.1 Unpacking.............................................................................12
4.2 Printer installation .................................................................12
4.3 Connecting the Power Adapter.............................................13
4.4 Connecting interface cable ...................................................14
4.5 Connecting the Cash Drawer................................................14
4.6 Paper roll loading..................................................................15
4.6.1 Confirm the paper type...................................................15
BTP-L580 User’s Manual
2
4.6.2 Load/replace a paper roll................................................15
4.7 Switching on and printing a self-test page ............................16
4.7.1 Switching on the printer..................................................16
4.7.2 Printing a self-test page..................................................16
5 PRINTER ROUTINE MAINTENANCE........................................18
5.1 Cleaning the platen...............................................................18
5.2 Cleaning the label sensors....................................................18
5.3 Clearing of a paper jam.........................................................19
6 INTERFACE SIGNAL .................................................................20
6.1 Parallel interface...................................................................20
6.2 Serial interface......................................................................21
6.3 USB interface........................................................................22
6.4 Ethernet interface .................................................................22
6.5 WLAN interface.....................................................................23
6.6 Signal definition of power connector.....................................24
6.7 Signal definition of cash drawer interface .............................24
7 TROUBLESHOOTING................................................................26
7.1 Printer doesn’t work..............................................................26
7.2 Alarm LED and buzzer sound...............................................26
7.3 Problems with printing ..........................................................26
7.4 Cutter resetting.....................................................................27
APPENDIX: FEED BUTTON CONFIGURATION ..........................28
BTP-L580 User’s Manual
1
1 Introduction
1.1 Outline
BTP-L580 thermal label printer has high performance. It can be used
for real-time label printing like for retail, storage, logistics, pharmacy,
etc.
This product can be connected to other equipment via Serial,
Parallel, USB, Ethernet or WLAN interfaces. The printer is supplied
with a user-friendly label creation software for use under
WINDOWS2000/XP/Server 2003/WIN7/Server 2008/VISTA.
1.2 Main Features
1) Low noise
2) 150mm/s high-speed printing
3) Easy paper loading
4) Easy operation and maintenance
5) Three different paper width
6) Auto paper cutting
7) Cash drawer control connector
8) Choice from several interfaces (“daughter boards”)
BTP-L580 User’s Manual
2
2 Main Specification
2.1 Technical Specification
Item Parameter
Print Method Direct Thermal
Resolution 203DPI
Print Speed 150mm/s (Max.)
Print Width 80mm (Max.)
Memory RAM: 2MB FLASH: 2MB
Interface
Optional Parallel(IEEE1248), Serial
(RS232C/RS485), USB, Ethernet, WLAN
Cash drawer 1~2 drives
Barcode Supported
1D:UPC-A, UPC-E, EAN8, EAN13,
CODABAR, CODE39, ITF,
CODE128,CODE93,
2D:PDF417,QR,MaxiCode
Fonts
ASCII Font A: 12×24; Font B:9×17;
Simplified Chinese（GB2312 or GB18030）,
Korean, Japanese, Traditional Chinese
selected
Character Enlarge 1-6 times
Character Rotation Rotate (0°, 90°, 180°, 270°)
Image process
Bitmap download: download 8 bitmaps at
most; buffer size is 12 KB
Direct bitmap print: support bitmap mode and
can execute quick bitmap print
Paper type Label paper，continuous paper
Label sensor Optical sensor
Paper near end sensor Optical sensor
Top cover position sensor Microswitch
Print head temperature
sensor
Thermistor
Power supply AC 220V±10%, 50~60HZ
Printer head lifetime 100KM
Operation condition 5℃~45℃, 20%~90% RH (40℃)
Storage condition -40℃~55℃, 20%~93%RH (40℃)
Dimensions 147 (W) × 205 (D) × 147 (H) mm
BTP-L580 User’s Manual
3
2.2 Cutter Specification
Item parameter Note
Cutter type Slide cutter
Cutting time 600ms The time that one cut
takes
Cutting interval 2s 30 times/min. (Max.)
Paper type
0.05-0.07mm
Liner paper
Operation voltage
24VDC
Max. static curren
1.2A
24VDC
Cutter lifetime
Only liner paper:
1,500,000 cuts.
The cutter should cut
only the liner and not cut
the liner together with the
label paper, otherwise it
will negatively affect the
lifetime of the cutter
Full or partial cuts
Full cut: cut off the label completely；
Partial cut: little connection left in middle. When in partial
cut mode, it is not allowed to retract paper, otherwise the
not completely cut paper may cause paper jam.
2.3 Paper Specification
2.3.1 Thermal Label Paper Parameter
Appearance:
Indice
Altri manuali SNBC Etichettatrice
