SNEED Coding Solutions SNEED PACK CS-5OTS Manuale utente

SNEED CODING SOLUTIONS | WWW.SNEEDCODING.COM

CS-5OTS USER GUIDE

www.sneedcoding.com | (833)926-3464 | support@sneedcoding.com

To Schedule a Call:

https://info.sneedcoding.com/meetings/richardturner/printer-introduction

Sneed Coding Help Desk:

https://help.sneedcoding.com/

www.sneedcoding.com | (833)926-3464 | support@sneedcoding.com

Thank you for your purchase of the SNEED-PACK CS-50TS top and side belt driven carton

sealer. In this manual you will find the basic operating and maintenance procedures to ensure

your success with the CS-50TS. Please read the manual carefully before operating the

equipment.

Safety Precautions

Keep hands clear of any moving parts while the case sealer is in

operation and always power down prior to inspection. Failure to do

so may cause bodily harm.

Risk of electric shock, make sure the machine is properly grounded

before use.

Do not alter the mechanical or electrical systems. Any changes

could result in malfunction or injury.

Always turn off power to the case sealer when changing the tape

roll or performing maintenance.

www.sneedcoding.com | (833)926-3464 | support@sneedcoding.com

Contents

Specifications ................................................................................................................................................ 4

Component Diagram..................................................................................................................................... 5

Setting up the Case Sealer ............................................................................................................................ 6

Adjusting the Deck Height ........................................................................................................................ 6

Installing the Roller Tables........................................................................................................................ 7

Adjusting for your Carton Dimensions...................................................................................................... 8

Installing the Tape..................................................................................................................................... 9

Adjusting the Tape Position .................................................................................................................... 10

Setting the Tape Tension ........................................................................................................................ 10

Common Issues ...........................................................................................................................................11

Circuit Diagram ...........................................................................................................................................12

Exploded Parts Diagrams ............................................................................................................................13

Main Body & Lift Mechanism.................................................................................................................. 13

Parts List..............................................................................................................................................14

Drive / Conveyance System .................................................................................................................... 17

Parts List..............................................................................................................................................18

Tape Head ............................................................................................................................................... 20

Parts List..............................................................................................................................................20

www.sneedcoding.com | (833)926-3464 | support@sneedcoding.com

Specifications

Speed: 18 m/min

Tape width: 1- 3 inch

Carton / case size: 15cm x 15cm ~ 50cm x 50cm

Machine Size:

Width: 90cm

Length: 102cm

Height: 135cm

Deck Height: 55cm ~ 72cm

Power supply: 220-240V/50-60Hz

Weight: 310 lbs

www.sneedcoding.com | (833)926-3464 | support@sneedcoding.com

Component Diagram

Box Height Adjustment

Tape Head

Case Stabilizers

Conveyance Belts

Tape Applicators /

Rollers

Removable Roller Tables

Box Width Adjustment

Side conveyance belts

Bottom tape head

www.sneedcoding.com | (833)926-3464 | support@sneedcoding.com

Setting up the Case Sealer

Adjusting the Deck Height

Figure 1

1. Begin by lifting the case sealer to the desired height with a pallet fork, dolly, or jack and

secure it safely in place.

2. Loosen the “adjustment bolts” on each leg and allow the “Height adjustment Insert” to drop

the floor.

3. Tighten the adjustment bolts and repeat these steps for each leg.

4. Once you have tightened all of the legs remove the lifting device holding the case sealer

in place.

Always consider safety and never lay down underneath the case sealer while

adjusting the legs.

Leg

Height Adjustment inserts

Adjustment bolts

Wheel Brake

Castor

Lock Nut

www.sneedcoding.com | (833)926-3464 | support@sneedcoding.com

Installing the Roller Tables

1. The fasteners (nuts) to attach the roller tables are already tightened onto their

corresponding bolt and will need to be removed first. *Only remove the first of two

fasteners (nuts)

2. Once the fasteners are removed place the roller tables onto the bolts and tighten them in

place.

fasteners

www.sneedcoding.com | (833)926-3464 | support@sneedcoding.com

Adjusting for your Carton Dimensions.

Figure 3

1. To set the case sealer to fit the dimensions of your carton/case use the adjustments shown

in Figure 3.

2. The adjustment handles will be installed backwards for shipping, remove them using the

included 10mm wrench and reinstall.

Carton width adjustment

Carton height adjustment

www.sneedcoding.com | (833)926-3464 | support@sneedcoding.com

Installing the Tape

1. Begin by attaching the tape arms to each tape head using the included screws. (top and

bottom)

2. Next Install the tape onto the tape wheel so that when you pull the tape down the adhesive

side is facing outward.

3. Now guide the tape under the first guide roller, over the one-way roller, and through the

clip just above the last guide roller. The red line in figure 5 shows the tape path.

Figure 5

Tape roll

Adhesive face

Guide roller

One -way roller

Adhesive face

Guide wheel

Adhesive face

Indice

Altri manuali SNEED Coding Solutions Attrezzature industriali

SNEED Coding Solutions

SNEED Coding Solutions JET Titan T6 Series Manuale utente

Manuali Attrezzature industriali popolari di altre marche

ABB

ABB Unifix AD Manuale

Mark 7

Mark 7 Evolution Manuale utente

Husky

Husky HyPET Manuale utente

bora

bora PM-1800 Manuale utente

Grizzly

Grizzly T32428 Manuale utente

Siemens

Siemens 8MF1 Series Manuale utente

ABB

ABB HT610965 Manuale utente

ABB

ABB SafeLink Manuale utente

Phoenix

Phoenix PHX-150 Manuale utente

ABB

ABB A165-L32 Manuale utente

ABB

ABB HT842936 Manuale utente

Rioned

Rioned UrbanJet Manuale utente

Hermetica

Hermetica 10 Series Manuale utente

HORNER

HORNER OEE Solution Manuale utente

Hammerhead

Hammerhead HG375 Manuale utente

SCHUNK

SCHUNK VERO-S NSE-A3 138 Istruzioni utente

ABB

ABB HT566657 Manuale utente

Webasto

Webasto GSE CAN Manuale utente