Solaire R4 Manuale utente
1
R4
Smart Heating Element
User Guide
2
• Security: Page 3
• Use in Accordance With Regulations : Page 3
• Safety Instructions: Page 3
• Pre installation: Page 4
• Element Control Panel: Page 4
• Using The Control Panel: Page 5
• WiFi App: Page 5
• Pairing The Element to The App: Page 6,7
• WiFi App Control Panel: Page 8
• Element Key Pad: Page 9
• Remote Control: Page 9
• Using The Remote Control: Page 10
• Setting The Timer with Remote Control: Page 11, 12
• Sending Data From The Remote To The Element: Page 13
• Restoring Deleted Data: Page 13
• Setting a Maximum Temperature Using The Remote: Page 13
• Setting a Password With The Remote: Page 13
• Deleting Entries During Data Entry: Page 14
• Switching Between Summer and Winter Time: Page 14
• Display All Saved Programmes: Page 14
• Automatic Settings: Page 14, 15
• Recycling And Disposal: Page 15
Contents
3
Please read this instruction manual
carefully and keep all applicable
documents for future reference.
Warnings are classified as follows:
This heating element is a component and must only be used if connected to a liquid-filled radiator
(e.g. towel rail or other suitable radiator).
The product must not be inserted into a flammable liquid. The liquid must be approved by the
manufacturer, distributor the professional installer.
Such radiators are suitable for increasing and maintaining the room temperature and/or drying
towels. When choosing the element’s power output (W), the manufacturer or distributor’s guidance
must be observed. The element’s wattage match the radiator’s specification. Inserting the element
into the wrong sized radiator is classed as improper use.
• Incorrect installation or operation can cause harm and damage the soundings.
• Touching live components risks fatal injury by electric shock.
• Do not work on the radiator (such as cleaning or repairs) until it has cooled down and disconnected from
the power source.
Ensure the Product’s degree of protection (IP rating) complies with the required degree of protection for the place of
installation.
Use in accordance with Regulations
General safety instructions
Security
Danger
Danger to life from electric shock
Danger
Danger to life or personal injury
Danger
Risk of property damage or damage to the environment
Use professional tools to tighten or loosen screw connections. Never
screw the heating element by hand. This will twist and brake the internal
connections. Which will void the product’s warranty.
Use a suitable spanner to screw the heating element into the radiator.
The element’s display must face forward (so it can be seen). Therefore it
is not necessary to use the last turn to screw the heating rod as far as it
will go.
The element must be screwed into the bottom of the radiator. Never at
the top
Caution Never try to separate the controller box the heating rod. The unit is connected and sealed at the factory. Opening the
element can lead to the destruction of the device and will void all warranty or liability claims.
4
Always observe the national regulations, standards, directives and laws. Children must not play with
the product or operate it .
The following work may only be carried out by persons who are sufficiently qualified. This is particularly
true for the electrical work.
• Assembly
• Dismantling
• Installation
• Inspection and Maintenance
• Repair
• Decommissioning
1. Observe all instructions and information accompanying the product the manufacturer or distributor of the radiator.
2. Comply with all relevant guidelines, standards, laws and others regulations.
Pre Installation
From 2018, electric room heaters must comply with Eco design Directive 2009 / 125 / EG. The aim of this
regulation is to save energy in the context of environmental protection.
The R4 fully complies with this regulation. Thus making any radiator fitted with the R4 compliant. This is
a necessity if the radiator is specified to be used as the room’s primary source of heat.
Ecodesign Policy
Controls
Controller
Flashing: Product is heating
Not Flashing: set temperature has
been reached
Set temperature
Thermostat is controlling the radiator’s
surface temperature
Frost protection mode. Will activate
if the temperature drops below 7°C.
Controller head can be
rotated by 180°
Heating the room to the target
temperature
Connection mode with the APP.
Light flashing: ready to connect
Light solid : connected
First steps
The heating element must be placed securely fitted into a liquid filled towel rail or a similar radiator.
The liquid should be a water/glycol mixture. Under no circumstances may flammable or hazardous
materials be used.
The R4 is a 230V (class I) appliance and must be connected to either a plug socket (if this is permitted
in the respective country) or to a fused connection box (according to the local regulations). Please
observe the required degree of protection for electrical devices in the instillation area. The installation
must be conducted by an appropriate specialist. We don’t accept any liability and obligations in the
event of improper installation or commissioning.
5
Using the control unit
After the element has been connected to the power supply, the symbol “--” will flash in the upper area
of the display. This indicates that the element is receiving power and ready for use. The element is in
the standby position.
Pressing the power button will switch the element from stand by to “On”.
The last temperature setting used will appear on the display.
If the Sun symbol flashes, this means the current temperature is different to the target
temperature.
If the current temperature is lower than the target temperature, the sun will flash slowly and the
element will start to heat.
If the sun is not flashing, the target temperature has been reached.
This is an input button with 4 functions, 2H, 4H, PC, RC.
By repeatedly pressing the button you move through each function:
• 2H (Boost)= The device works at maximum power for 2 hours and will return to the previous mode.
• 4H (Boost)= The device works at maximum power for 4 hours.
Upon completion of the boost term the device will return to the previously selected temperature.
• PC = APP mode to control with the APP
• RC = Program mode from the remote control
The hourglass indicates a timed program has expired.
Attention: If the element is disconnected from the power supply, the settings will be lost. However, settings from the app
and remote control are retained.
Change the target temperature in 5°C increments.
WiFi App and control
Download the App
• Download and install the “SolAire WiFi IQ” APP from either the Android Play Store or the iOS APP Store
• Now you will need to create an account. If you already have an account, sign into the existing account.
An account can be registered under either a phone number or email address. If you enter a phone number, a verification number will
be sent to your phone: enter this number to verify, then create a password. If you enter your email address, you’ll just need to create a
password.
6
Setting the element to WiFi pairing
mode
Resetting the Device
1) Turn the Device
on
2) Go to app mode “PC” Press for 5 seconds until the beep
sounds
Flashes fast / slow
The device is ready to pair
When this symbol is flashing
fast. If not flashing fast, reset
the device.
Auto Pairing
Pairing the element to the App
2) Press Add Device
1 Open the App 3) The App will search for the device
4) Press Add
↑
↑
5) Now press the plus Icon.
Then”Done”
Towel Rail
Before pairing, make sure the element has been set to pairing mode.
7
↑
↑
6) Enter WiFi details
and press Next 8) Once connected, the
above image will be
displayed.
Now name the device and
save
7)The App will then
begin to pair with the R4.
Wait until the App
prompts you to proceed.
Manual Pairing
Add
↑
↑
2) Enter WiFi details and
press Next
3) Ensure the device is
flashing quickly. Then
press Next
↑
5) Once connected, the above image will be displayed.
Now name the device and save
4) The App will then begin
to pair with the R4.
Wait until the App
prompts you to proceed.
1) Press Add device, then select Heater (WiFi). This
can be found under “Small home appliances”, if not
immediately visible.
If the heater does not appear, as showing step 3, add the heater manually.
8
App’s Control Panel
Edit Device Name
Target temperature
Using the slider, adjust the target temperature.
Device settings
• Room temperature compensation
• Weekly programming
• Lock device
• Open window detection
• Maximum surface temperature
Boost mode
Heating for 2 or 4
Hours at the highest
power level
ON / OFF
(Stand by)
Back to device list
9
Element’s Keypad
Remote Controller
If the element is disconnected from the power supply the controller will loose the program data. When
power is restored, the controller will switch to the last used water temperature.
The program data must be re-sent to the element from the remote control. The remote will store the
programme data.
On / Standby” button
(With acoustic signal)
Adjust target temperature
Fixed program functions
(Press button several times)
2H
2 hour boost function
4H
4 hour boost function
PC
APP mode to control with the APP
RC
Control from remote control
Remote Controller
IR remote control
(Supplied Separately)
10
Using the remote control
To remove the protective foil
The display of the remote control is protected by a foil. This can removed before use.
Inserting the batteries
Open the cover at the back of the remote control. Then insert the two batteries (2 pieces, type AAA, 1.5 V) into the
slot.
Wall mount for remote control
The wall bracket included can be attached using the included mounting parts. The remote holder / bracket can be
attached to the wall.
Buttons on the remote control
Weekdays 1-7 (Mon-Sun)
Selected day of the week
Summer/ Winter time
Time
Batteries (2 pieces type AAA 1.5V) are not included
Do not use the remote control in the bath, shower etc. Keep the remote
control far away from water and other liquids.
Send button (Send programme to the element)
Basic settings (date, time)
Work settings (e.g. switching times)
Reduce value
Increase value
Check program, enter password
Confirmations, undo
Indice
