Solartron DR600 Manuale utente
installation manual
Model No. DR600 & DR700
Digital Readout
1.0 Index 2
Section Title Page
1.0 Index . . . . . . . . . . . . . . . . . . . . . . . 2
2.0 Safety Summary . . . . . . . . . . . . . . . 3
3.0 Service & Repair . . . . . . . . . . . . . . 5
4.0 Measurement Configurations . . . . . 6
5.0 Digital Readout Interface . . . . . . . . 7
6.0 Probe Interface/
Orbit Network Connections . . . . . . . 9
7.0 RS232 . . . . . . . . . . . . . . . . . . . . . . . 10
8.0 Input/Output Connections . . . . . . . . 13
9.0 Motor Drive Connections . . . . . . . . . 17
10.0 General Specification . . . . . . . . . . . . 18
Return of Goods
Part No. 502001 Issue 6
1.0 Index
Part No. 502001 Issue 6
3
2.0: Safety Summary
2.0: Safety Summary
This Equipment is designed as Safety Class I
apparatus to comply with EN61010-1.
Service Safety
This equipment has been designed and tested to
meet the requirements of the Low Voltage Directive
(1997) and has been supplied in a safe condition.
This manual contains information and warnings
that must be followed by the user to ensure safe
operation and to retain the apparatus in a safe
condition.
Terms in this Manual
WARNING statements identify conditions or
practices that could result in personal injury
or loss of life.
CAUTION statements identify conditions or
practices that could result in damage to the
equipment or other property.
Symbols in this Manual
This symbol indicates where applicable
cautionary or other information is to be
found.
Power source Apply no more than 265V rms
(AC) between supply conductors or conductor
and ground.
Part No. 502001 Issue 6
4
2.0: Safety Summary
2.0: Safety Summary (continued)
WARNING: Do not operate in an explosive
atmosphere
WARNING: Do not remove covers or panels
To avoid personal injury, do not remove covers
and panels. Do not operate the equipment without
the covers and panels fitted. There are no internal
adjustments required during commissioning the
equipment.
Warning: Danger arising from loss of ground
During a fault condition and upon loss of protective
ground (earth) connection, all accessible conducting
parts - including controls that might appear to be
insulated - can render an electric shock.
CAUTION: Use correct Fuse
To avoid a fire hazard, use the correct
fuse type, voltage and current rating as
specified for the equipment. Refer fuse
replacement to qualified service personnel.
Grounding the equipment
The unit is grounded through the mains lead:
to avoid electric shock, plug the power lead into
a properly-wired receptacle before connecting to
the input or output terminals. A protective ground
connection by the way of the grounding conductor
in the power lead is essential for safe operation.
Part No. 502001 Issue 6
5
3.0: Service & Repair
3.0: Service & Repair
Replacing the fuse
At the rear right of the Digital Readout
remove the fuse cover of the IEC320
connector and replace the fuse with the
same 20mm type and value.
This equipment contains no user serviceable
parts other than the fuse.
This equipment must be returned to your Solartron
dealer for all other service and repair.
Dismantling the unit will invalidate the warranty.
Part No. 502001 Issue 6
6
3.0: Handling & Maintenance
4.0: Measurement Congurations
Individual probe -connection of one Linear
Encoder or Digital Probe.
Probe pair - connection of 2 probes
configured as A+B or A-B.
Probes may be plugged directly into the rear panel
recessed receptacle.
Multiple probes - up to 10 individual probes
or probe pairs (A+B or A-B)
each allocated to a program.
DR600 only
Scan - connection of up to 30 probes
(Linear Encoders and/or
Digital Probes) and allocated
to a single program.
DR700 only
Gauging mode - connection of up to 30 probes
(Linear Encoders and/or Digital
Probes) each with its own limits
and preset. Global Pass/Fail.
Refer to Digital Readout User Manual to configure
the options.
To connect more than 2 probes to the Digital
Readout, use the Orbit Network Connection
System.
When more than 10 probes are connected to
the Digital Readout a supplementary power supply
interface module will be required
(Solartron Part No. 911173).
Part No. 502001 Issue 6
7
RS232
IEC 320 CONNECTOR
85V - 264V
15W max
INPUT/
OUTPUT
CONNECTOR
CONNECTOR
PROBE INTERFACE/
ORBIT NETWORK
CONNECTORS
Earth stud provided
for bonding to machine
safety earth.
(CAUTION: DO NOT USE
FOR CONNECTION TO LVD T
OR HALF BRIDGE GAU GING
PROBES)
MOTOR DRIVE CONNECTION
5.0: Digital Readout Interface
5.0: Digital Readout Interface
Probe(s) must be identified to the Digital Readout
when first installed. Simply press probe tip when
prompted.
5.1 Connecting 1 or 2 Probes
To connect a Linear Encoder or Digital Probe
ensure cable from Probe Interface Electronics (PIE)
is at bottom of unit and plug into either left hand or
right hand side of recessed receptacle.
Part No. 502001 Issue 6
8
5.0: Digital Readout Interface
(continued)
5.0: Digital Readout Interface (continued)
5.2: Connecting up to 30 probes
Installation using T-CON
solartron
69
51
Mixed probe
capability
solartron
ORBIT Network
Plug cable into either lefthand
or righthand side of recessed
receptacle in rear panel
9-way cable
zero motor
print
setup 456
escape 123
0-/+
enter789
solartron
program
preset mx/mn mm
refprogram
. Accessories
T-CON part number 971000
9 pin (m/f) cable 1.5m 006869
9 pin (m/f) cable 5m 803664
Part No. 502001 Issue 6
9
6.0: Probe Interface/Orbit
Network Connections
6.0: Probe Interface/Orbit Network Connections
Connector type: 9 way D-sub female
Pin Function
1 0V
2 RS485(A)
3 RS485(B)
4 0V
5 0V
6 +5V
7 +5V
8 +5V
9 0V
1
2
6
3
7
4
8
5
9
1
2
6
3
7
4
8
5
9
View from rear of unit
Part No. 502001 Issue 6
10
7.0: RS232
7.0: RS232
(Allows measurement readings to be sent
to printer or PC)
Connector type 25 way D-sub female
7.1: Pin Assignment
Pin Signal Assignment
1 CHASSIS GND Chassis ground
2 TXD Transmitted data
3 RXD Received data
4 RTS Request to send
5 CTS Clear to send
6 DSR Data set ready
7 SIGN GND Signal ground
20 DTR Data terminal ready
7.2: Voltage Levels
TXD and RXD voltage levels
logic level (active) -3V to -15V
logic level (not active) +3V to +15V
RTS, CTS, DSR and DTR voltage levels
logic level (active) +3V to +15V
logic level (not active) -3V to -15V
7.3 Connection Cable
Simple connection between Digital Readout
and printer or PC
(No flow control or Xon/Xoff flow control)
13
2120191817161514 25
24
2322
1211109876
5
4321
11Chassis gnd RTS/CTS Control = no
&
DTR/DSR Control = no
in RS232 menu
22TXD
33RXD
7
Digital Readout Printer or PC
7 Signal gnd
Questo manuale è adatto per i seguenti modelli
1
Indice
Manuali Attrezzature da laboratorio popolari di altre marche
Agilent Technologies
Agilent Technologies 5800 ICP-OES Manuale utente
Endress+Hauser
Endress+Hauser Cleanfit CPA875 Manuale utente
NI
NI PXI-5422 Manuale
Collomix
Collomix Aqix Manuale utente
SPEX SamplePrep
SPEX SamplePrep 6875 Freezer/Mill Series Manuale utente
Ocean Insight
Ocean Insight FLAME-NIR+ Manuale utente
