SolidGripSystems Twin Dolly Guida all'installazione

SolidGripSystems - Emrikweg 27 - 2031BT - Haarlem - The Netherlands

Phone +3123 7370368 - www.solidgripsystems.eu -info@solidgripsystems.eu

Twin Dolly and TwinTube Unpack and Set Up instructions

Contents

TwinTube Undersleepers installation ....................................................................................................................2

Junior Stud Installation and Usage instructions ....................................................................................................3

TwinSliderBase Set Up............................................................................................................................................4

End Stop Set Up ......................................................................................................................................................5

Bowl Risers Set Up ..................................................................................................................................................6

TwinDolly ................................................................................................................................................................7

Precautions and Notes........................................................................................................................................7

General Remarks.................................................................................................................................................7

Offset Axle Adjustment Procedure ....................................................................................................................8

Set up for use on a standard Rigging Truss........................................................................................................9

BNC Arm..............................................................................................................................................................9

4 Way Leveler......................................................................................................................................................9

TwinTube Set Up examples ..................................................................................................................................10

SolidGripSystems - Emrikweg 27 - 2031BT - Haarlem - The Netherlands

Phone +3123 7370368 - www.solidgripsystems.eu -info@solidgripsystems.eu

Twin Dolly and TwinTube Unpack and Set Up instructions

TwinTube Undersleepers installation

When receiving a new set of TwinTubes without the optional Flightcase TTF300 or TTF150 you need to install the

UnderSleepers.

TwinTubes delivered with the optional FlightCase will have the UnderSleepers pre-installed.

Tools: Allen key 5mm

Instruction

Place the TwinTube upside down

Remove the pre-installed Allen key screws (4)*

Install the UnderSleepers (see picture) at both

CrossTies

* In some cases the Allen screws are not pre-installed but added

separately.

Note: Make sure to align the Undersleeper exactly as

displayed on the drawing

SolidGripSystems - Emrikweg 27 - 2031BT - Haarlem - The Netherlands

Phone +3123 7370368 - www.solidgripsystems.eu -info@solidgripsystems.eu

Twin Dolly and TwinTube Unpack and Set Up instructions

Junior Stud Installation and Usage instructions

Tools: None

Instruction

Manually insert the Junior stud in the dedicated screw

hole and fasten it hand-tight.

Note: the Junior Stud uses the 3/8 UNC camera

thread.

Insert the Junior stud in a junior receiver/Light Stand

(28mm)

SolidGripSystems - Emrikweg 27 - 2031BT - Haarlem - The Netherlands

Phone +3123 7370368 - www.solidgripsystems.eu -info@solidgripsystems.eu

Twin Dolly and TwinTube Unpack and Set Up instructions

TwinSliderBase Set Up

Tools: Allen key 5mm

Instruction

Righthand side picture shows the unmounted

TwinSlider Base.

Remove the pre-installed (angled) Allen key

screws (4) and take of the 2 clamps from the

TwinSliderBase.

Insert the 2 clamps from the top side of the

TwinTube section.

Install the TwinSliderBase from underneath

the TwinTube section and align with under the

clamps.

Install the 4 Allen screws and tighten them

equally.

Example of an installed set up.

SolidGripSystems - Emrikweg 27 - 2031BT - Haarlem - The Netherlands

Phone +3123 7370368 - www.solidgripsystems.eu -info@solidgripsystems.eu

Twin Dolly and TwinTube Unpack and Set Up instructions

End Stop Set Up

Tools: None

Instruction

Always install the End Stops at both ends before

adding the TwinDolly onto the TwinTubes.

Righthand side picture shows how the End Stops have

to installed.

Loosen the black knob a few turns and slide the End

Stop over the TwinTube CenterCross as shown.

Hand tighten the black knob and check if the End Stop

is firmly mounted onto the CenterCross by gently

pulling the End Stop.

Example of an installed set up with an End Stop at

both ends.

SolidGripSystems - Emrikweg 27 - 2031BT - Haarlem - The Netherlands

Phone +3123 7370368 - www.solidgripsystems.eu -info@solidgripsystems.eu

Twin Dolly and TwinTube Unpack and Set Up instructions

Bowl Risers Set Up

Tools: 10 mm (open) wrench

Instruction

The bowlrisers are intended to raise (or lower) the

bowl away from the fixed mounting studs of the

TwinDolly.

Righthand side picture shows the underslung option of

the bowl risers.

Remove the 4 Allen screws that hold the bowl.

Insert the bowl risers at the position of the

above mentioned 4 Allen screws.

Tighten the bowl risers with an appropriate

tool (10 mm wrench).

Mount the bowl onto the BowlRisers using the

4 Allen Screws from step 1.

SolidGripSystems - Emrikweg 27 - 2031BT - Haarlem - The Netherlands

Phone +3123 7370368 - www.solidgripsystems.eu -info@solidgripsystems.eu

Twin Dolly and TwinTube Unpack and Set Up instructions

TwinDolly

Tools: 13 mm open wrench and 5 mm Allen key

Operation Instructions

Precautions and Notes

Using common sense nothing can go wrong.

Whenever possible use Tip Protection. [1]

Always use clamps or junior studs as end

stoppers if our End-Stops are not available.

Two of the side wheels of a TwinDolly/TrussDolly

are mounted on offset axles. This makes it

possible to adjust the track width 6mm per axle,

thus 12mm per TwinTube or truss. Remember to

use the same setting for each axle, otherwise the

dolly will run obliquely along the rails.

General Remarks

All bolts that are not intended to be removed are

factory treated with Loctite 2701.

Excluded are: Brake, Tip Protection, Wheel shafts.

The top wheels have a diameter of 62mm and a

hardness of 78A.

The TWD side wheels have a hardness of 94A.

These values are the result of extensive testing.

Deviating from these values may negatively effect

the operation of the TwinDolly.

SolidGripSystems - Emrikweg 27 - 2031BT - Haarlem - The Netherlands

Phone +3123 7370368 - www.solidgripsystems.eu -info@solidgripsystems.eu

Twin Dolly and TwinTube Unpack and Set Up instructions

Tools: 13 mm open wrench and 5 mm Allen key

Operation Instructions

Offset Axle Adjustment Procedure

Fully release the brake.

Locate the Offset wheels opposite of the

Brake.

Loosen the Allen bolts of the wheel sets half

a turn. [2]

Use a 13mm wrench between the wheel

and the dolly to turn the axle to the desired

position. [3]

When the desired position is achieved re-

tighten the axle with an Allen key.

Check that the dolly can run freely in a

straight line without play but also without

too much pressure.

If the wheels are over tightened flat spots

can occur resulting in a bumpy dolly

movement.

If the wheels are too loose there will be play

in the dolly which will be felt at camera

pans.

SolidGripSystems - Emrikweg 27 - 2031BT - Haarlem - The Netherlands

Phone +3123 7370368 - www.solidgripsystems.eu -info@solidgripsystems.eu

Twin Dolly and TwinTube Unpack and Set Up instructions

Tools: 13 mm open wrench and 5 mm Allen key

Operation Instructions

Set up for use on a standard Rigging Truss.

When using wider truss or rigging, the offset

axles can be placed in the outer holes.[4].

Further adjustment is similar to the previous

described process.

BNC Arm

The hinged arm is intended to hold BNC or power

cables at a comfortable distance from the

dolly.[5]

4 Way Leveler

Installation of the SolidGripSystems 4-Way-

leveler goes best when following the next

suggestion:

first turn three of the leveling bolts of the leveler-

head maximum out and the remaining bolt fully

inwards before starting to assemble.

SolidGripSystems - Emrikweg 27 - 2031BT - Haarlem - The Netherlands

Phone +3123 7370368 - www.solidgripsystems.eu -info@solidgripsystems.eu

TwinTube Set Up examples

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Accessori video professionali popolari di altre marche

Yongnuo

Yongnuo YNSOFT Series Manuale utente

Glidecam

Glidecam 2000 Pro Manuale utente

PROAIM

PROAIM CINEMA Series Manuale utente

Glide Gear

Glide Gear REVO 150 Manuale utente

AUTOCUE

AUTOCUE SSPi Manuale utente

PROAIM

PROAIM TP-ULTM-01 Manuale utente

Sony

Sony VCT-SP2BP Manuale utente

MRMC

MRMC Polymotion Chat Studio 3.1.0 Manuale utente

CDA-TEK

CDA-TEK AFX Manuale utente

ARRI

ARRI TRINITY Manuale utente

Senna

Senna One Minute Long Crane Manuale utente

Ikan

Ikan PT4900S-PTZ Manuale utente

PROAIM

PROAIM Gladiator Action Dolly Manuale utente

Ikan

Ikan PT4200-P2P Manuale utente

Ikan

Ikan PT4900-TK Manuale utente

Filmcity

Filmcity FC-TP100 Manuale utente

CDA-TEK

CDA-TEK PBC Manuale utente

PROAIM

PROAIM CINEMA Series Manuale utente