Soloshot SOLOSHOT2 Manuale utente
Camcorder Bundle
- instructions for use -
Step 1.0 | Safety First
Please read the and warnings
carefully before using the product.
SAFETY INSTRUCTIONS
Step 1.1 | Update Firmware
-You must update your firmware. Please do so
now before proceeding with instructions.
Important
Click for firmware update instructions.HERE
Step 1.2 | Connect Base
Connect Base to Tripod.
Step 1.3 | Hand Tighten
Screw the Base onto your tripod until you feel light
resistance from the motor.
Step 1.4 | Tool Tighten
Use Tripod Tool to finish tightening.
Step 1.5 | Attach Camera
Attach your camera to the Base using the mounting screw
and spinning wheel.
Step 1.6 | Align Camera
Make sure your camera points in the same direction as
the tracking LED.
Step 1.7 | Camera Settings
Turn on your CX-240 or CX-405 by opening the screen.
Adjust settings below(click for details):
= Auto.FOCUS
= Active.STEADYSHOT
= Limited by your SD card quality
and size. We recommend 60p.
IMAGE QUALITY
= Turn off.iAUTO
Step 1.8 | Camera Controller
This is your Camera Controller.
Step 1.9 | Multi Cable
This is your Multi Cable for controlling your CX-405/CX-240
camera.
Step 1.10 | Power Cable
This is your Power Cable for powering your CX-405/CX-240
camera.
Step 1.11 | Insert Cables
Open silicone cover on side of your Camera Controller.
Insert the appropriate ends of the Multi Cable and Power
Cable into the Camera Controller.
Step 1.12 | Dock Controller
Dock your Camera Controller into the accessory port on
your Base.
Step 1.13 | Connect Multi
Connect the free end of the Multi Cable to the Multi Port
on your camera.
Step 1.14 | Connect Power
Connect the female end of your Power Cable to the
camera's USB.
Note: SOLOSHOT can only power certain cameras (CX-405
and CX-240).
Travel Tip
IMPORTANT:Unplug all cables from Camera Controller
and camerawhen transporting your SOLOSHOT.
Step 1.15 | Charge Base
Open side flap on Base.
Plug mini USB end of charging cable into side of
Base.
Plug USB end of cable into standard walll adaptor
(included with SONY camcorder).
Plug adaptor into wall socket.
Charging indicator on Base will be RED while
charging and GREEN when ready.
Step 1.16 | Charge Tag
While holding the Tag at a 45-degree angle, dock the
Tag into Accessory Port on Base.
Tag will click into place.
LED above Tag’s power button will turn when
charging and when fully charged.
RED
GREEN
Slide the dock button down to release Tag.
Note: Base must also be plugged in to charge Tag.
Step 2.0 | Base On/Off
Base Power:
On -Press power button.
Off - Press and hold power button for 6 seconds.
Note: LED 3 will only illuminate if Camera Controller
is connected.
Step 2.1 | Tag On/Off
Tag Power:
On - Press power button. LED 1 will turn .RED
Off - Press and hold power button for 6 seconds.
Step 2.2 | LEDs 1-6
The 6 LEDs on your Base representdifferent settings.
Each LED/Setting can be toggled between different
operating modes based on your needs.
LED 1 = Tilt Setting
LED 2 = Trajectory Setting
LED 3 = Zoom Setting
LEDs 4 - 6: SettingsMULTI MODE
Step 2.3 | Change Modes
Change Modes by changing the color of the blinking LED:
Cycle through colors/modes by pressing the M
button.
Step 2.4 | Change Settings
Jump to the next LED/Setting by a quick pressing of the
power button.
The active LED/Settingwill blink.
Step 2.5 | LED 1 | Tilt Setting
Selectyour tilt mode by changing LED 1color based on
your activity's requirements as described below.
LED 1 = GREEN
Surf & Turf Mode:
Great for activities performed on a level surface like
surfing, kiteboarding, soccer and wakeboarding.
is now built into Surf & Turf!JUMP Detection
LED 1 = RED
Big Altitude Mode:
Great for activities with large altitude changes
(Examples: snowboarding andRC planes).
Requireswider framing.
Altri manuali per SOLOSHOT2
1
Indice
Altri manuali Soloshot Accessori per fotocamere
