SONIQ FMFTSSBR Manuale utente
Turntable & Bookshelf Speaker Set
FMFTSSBR
WELCOME
CONTROL AND INTERFACE
Thank for choosing this product.
Please read the User Manual carefully and keep it for future reference.
1. Turntable
2. Slip Mat
3. Lift Lever
4. Tone Arm Clip
5. AUTO STOP Switch
6. 33/45/78 RMP Switch
7. Turntable Shaft
8. Tone-arm
9. LED Indicator
10. Volume Knob
11. Stylus Cartridge
12. Audio Output Jack
13. Function Mode Switch
14. RCA Output Jack
15. DC IN Jack
16. Power Switch
17. Audio Input Jack
1
GETTING STARTED
Connect the unit with the external Speakers rst, then plug the Adaptor to the DC IN Jack,
and nally plug the Adaptor in to a power outlet.
PHOTO MODE
1. Turn on the Power Switch. Switch to PH mode. The LED indicator will light up red.
2. Place Vinyl Record on Turntable and select appropriate speed (33/ 45/ 78) according to
the Record. NOTE: when playing a 45RPM record, use the supplied 45RPM Adaptor to
support the Record.
3. Remove the Stylus Protector. Open the Tone-Arm Clip to release the Tone-Arm. Push
the Lift Lever backward to raise the Tone-Arm and gently move the Tone-Arm to the
desired position over the Record. The Turntable will begin to spin when the Arm is
moved toward the Record. Push the Lift Lever forward to lower the Tone-Arm slowly
onto the Record to play it.
4. If the AUTO STOP Switch is turned on, the Turntable will stop automatically when it
comes to the end of the Record. If AUTO STOP Switch is turned o, the Turntable will
NOT stop automatically when nished.
5. Turn the Volume Knob to adjust the volume.
To replace Stylus, please refer to the following instructions:
To remove Stylus from Cartridge
1. Hold and pull down the Stylus as shown in direction “A”.
2. Remove the Stylus by pulling the Stylus forward.
To install the Stylus
1. Insert a Stylus by pressing as shown in direction “B”.
2. Push the Stylus upward as in direction "C" until the Stylus locks into position.
REPLACE STYLUS
2
Guide Pins(inside)
1. Switch the function mode to Bluetooth. The indicator will ash blue.
2. Open the Bluetooth function of the Pairing Device. Search for “FMFTSSBR” from your
list, and select to connect. Once successfully paired, the LED indicator turns to blue.
3. Play music from your Device’ selection.
4. Turn the Volume Knob to adjust the volume.
BLUETOOTH MODE
You can connect this unit to an external Hi-Fi / Amplier System with an RCA Cable (not
included).
LINE OUT CONNECTION
RMS Power: 2x10W
SNR: ≤40dB
Frequency Response: 125Hz－6.3KHz
Power Supply Voltage: 12V
SPECIFICATION
1. When opening or closing the turntable cover, handle it gently.
2. Do not touch the Stylus Tip with your Fingers; avoid bumping the Stylus against the
Turntable or Record edge.
3. Frequently clean the Stylus Tip using a soft brush in a “back-to-front’ motion only.
4. Use a needle cleaning uid sparingly.
5. Gently wipe the turntable player housing with a soft cloth. Use only a small amount of
mild detergent to clean the turntable player.
6. Never use harsh chemicals or solvents on any part of the Turntable System.
If there are any queries or product is not performing as it should, please contact QUATIUS
Service Center at 1300 765 663 for technical support.
TIPS FOR BETTER TURNTABLE PERFORMANCE
3
Indice
Altri manuali SONIQ Sistema di altoparlanti
Manuali Sistema di altoparlanti popolari di altre marche
Sondpex
Sondpex Active Speaker System and Digital Music... Manuale utente
JVC
JVC NX-PN7 Manuale utente
Marshall Amplification
Marshall Amplification AR-DM61-BT Manuale utente
Yamaha
Yamaha NX-A01 - Speaker Sys Manuale utente
SE Audiotechnik
SE Audiotechnik I-LINE Manuale utente
Gemini
Gemini WRX-843 Series Manuale utente