Sony HCD-DX375 Manuale utente

SERVICE MANUAL
Sony Corporation
Home Audio Division
Published by SonyTechno Create Corporation
US Model
SUPER AUDIO CD/DVD RECEIVER
9-887-160-02
2006D16-1
© 2006.04
Ver. 1.1 2006.04
HCD-DX375
HCD-DX375 is the amplifier, DVD/CD and tuner
section in DAV-DX375.
SPECIFICATIONS
Model Name Using Similar Mechanism HCD-DX255
Mechanism Type CDM81C-DVBU101
Optical Pick-up Name
KHM-310CAB
This system incorporates with Dolby*1Digital and Dolby Pro Logic (II)
adaptive matrix surround decoder and the DTS*2Digital Surround
System.
*1 Manufactured under license from Dolby Laboratories.
“Dolby,” “Pro Logic,” and the double-D symbol are trademarks of
Dolby Laboratories.
*2 Manufactured under license from Digital Theater Systems, Inc.
“DTS” and “DTS Digital Surround” are trademarks of Digital
Theater Systems, Inc.
— Continued on next page —
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND
TOTAL HARMONIC
DISTORTION
(FTC Output Power): FL/FR/SL/SR/C: 84 W/ch
3 ohm at 170 - 20,000 Hz,
0.7 % THD
SW: 160 W 1.5 ohm at 40 -
170 Hz, 0.7 % THD
Amplifier section
Surround mode (reference)
RMS output power, 10 %
THD
Front: 143 W + 143 W
(with SS-TS52)
Center*: 143 W
(with SS-CT51)
Surround*: 143 W + 143
W
(with SS-TS51)
Subwoofer*: 285 W
(with SS-WS52B)
*Depending on the sound field settings and the source,
there may be no sound output.
Inputs
TV, VCR (AUDIO IN) Sensitivity: 450/250 mV
AUDIO IN Sensitivity: 250/125 mV
Outputs (Analog)
Phones Accepts low-and high-
impedance headphones.
Super Audio CD/DVD system
Laser Semiconductor laser
(Super Audio CD/DVD:
λ= 650 nm)
(CD: λ= 790 nm)
Emission duration:
continuous
Signal format system NTSC
Harmonic distortion Less than 0.03 %
Tuner section
System PLL quartz-locked digital
synthesizer system
FM tuner section
Tuning range 87.5 – 108.0 MHz
(100 kHz step)
Antenna (aerial) FM wire antenna (aerial)
Antenna (aerial) terminals 75 ohms, unbalanced
Intermediate frequency 10.7 MHz
AM tuner section
Tuning range 530 – 1,710 kHz (with the
interval set at 10 kHz)
531 – 1,710 kHz (with the
interval set at 9 kHz)
Antenna (aerial) AM loop antenna (aerial)
Intermediate frequency 450 kHz
Video section
Outputs VIDEO: 1 Vp-p 75 ohms
S VIDEO:
Y: 1 Vp-p 75 ohms
C: 0.286 Vp-p 75 ohms
COMPONENT:
Y: 1 Vp-p 75 ohms
PB/CB, PR/CR: 0.7 Vp-p
75 ohms
HDMI OUT:
Type A (19 pin)

2
HCD-DX375
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
•Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
•Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
•Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
Notes on chip component replacement
•Never reuse a disconnected chip component.
•Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
•Keep the temperature of the soldering iron around 270 °C
during repairing.
•Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
•Be careful not to apply force on the conductor when soldering
or unsoldering.
CAUTION
Use of controls or adjustments or performance of procedures
otherthan thosespecifiedhereinmay resultin hazardousradiation
exposure.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0OR DOTTED LINE
WITH MARK 0ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety check before releasing the set to the customer:
Check the antenna terminals, metaltrim, “metallized” knobs, screws,
and all other exposed metal parts forAC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
1. Acommercial leakage tester, such asthe Simpson 229 orRCA
WT-540A. Follow the manufacturers’instructions to use these
instruments.
2. A battery-operatedAC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOMor battery-operatedACvoltmeter.The “limit”indication
is 0.75V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2VAC range are suitable. (See
Fig. A)
1.5 k
Ω
0.15
µ
FAC
voltmete
r
(0.75 V)
To Exposed Metal
Parts on Set
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
General
Power requirements 120 V AC, 60 Hz
Power consumption On: 160 W
Standby: 0.3 W (at the
Power Saving mode)
Dimensions (approx.) 430 ×86 ×418 mm
(17 ×3 1/4×16 3/4inches)
(w/h/d) incl. projecting
parts
Mass (approx.) 5.2 kg (11 lb 8 oz)
Design and specifications are subject to change
without notice.

3
HCD-DX375
TABLE OF CONTENTS
1. SERVICING NOTE ................................................... 4
2. GENERAL ................................................................... 11
3. DISASSEMBLY
3-1. Disassembly Flow ........................................................... 14
3-2. Case, Front PanelAssy .................................................... 15
3-3. FL Board, SW Board....................................................... 16
3-4. JACK Board, LED Board ................................................ 16
3-5. DMB12 Board ................................................................. 17
3-6. I/O Board, Tuner.............................................................. 18
3-7. SPEAKER Board, D.C. Fan ............................................ 18
3-8. MAIN Board.................................................................... 19
3-9. POWER Board ................................................................ 20
3-10. DVD Mechanism Deck (CDM81C-DVBU101) ............. 21
3-11. TRAY .............................................................................. 22
3-12. MOTOR Board M761 (LD/ST Motor),
M762 (BU U/D Motor) ................................................... 22
3-13. BASE UNIT (DVBU101)................................................ 23
3-14. Optical Pick-up (KHM-310CAB) ................................... 23
3-15. Gear (Sub Tray 1), Gear (Sub Tray 2) ............................. 24
3-16. Lever Assy ....................................................................... 24
3-17. Stocker Section ................................................................ 25
3-18. Cam (Stocker).................................................................. 25
3-19. Gear (Stocker 3) .............................................................. 26
3-20. Rotary Encoder (MD)...................................................... 26
3-21. Gear (BU1) ...................................................................... 27
4. TEST MODE ............................................................... 28
5. ELECTRICAL ADJUSTMENT ............................. 32
6. DIAGRAMS
6-1. Block Diagram – RF Section –....................................... 34
6-2. Block Diagram – AMP Section – ................................... 35
6-3. Block Diagram – AUDIO Section – ............................... 36
6-4. Block Diagram – VIDEO Section – ............................... 37
6-5. Block Diagram – POWER Section –.............................. 38
6-6. Printed Wiring Board – DMB12 Board (SideA) – ......... 39
6-7. Printed Wiring Board – DMB12 Board (Side B) – ......... 40
6-8. Schematic Diagram – DMB12 Board (1/7) –................. 41
6-9. Schematic Diagram – DMB12 Board (2/7) –................. 42
6-10. Schematic Diagram – DMB12 Board (3/7) –................. 43
6-11. Schematic Diagram – DMB12 Board (4/7) –................. 44
6-12. Schematic Diagram – DMB12 Board (5/7) –................. 45
6-13. Schematic Diagram – DMB12 Board (6/7) –................. 46
6-14. Schematic Diagram – DMB12 Board (7/7) –................. 47
6-15. Printed Wiring Board – MAIN Board (Side A) –............ 48
6-16. Printed Wiring Board – MAIN Board (Side B) –............ 49
6-17. Schematic Diagram – MAIN Board (1/6) – ................... 50
6-18. Schematic Diagram – MAIN Board (2/6) – ................... 51
6-19. Schematic Diagram – MAIN Board (3/6) – ................... 52
6-20. Schematic Diagram – MAIN Board (4/6) – ................... 53
6-21. Schematic Diagram – MAIN Board (5/6) – ................... 54
6-22. Schematic Diagram – MAIN Board (6/6) – ................... 55
6-23. Printed Wiring Board – I/O Board – ............................... 56
6-24. Schematic Diagram – I/O Board – ................................. 57
6-25. Printed Wiring Boards – PANEL Section –..................... 58
6-26. Schematic Diagram – PANEL Section – ........................ 59
6-27. Printed Wiring Board – SPEAKER Board – ................... 60
6-28. Schematic Diagram – SPEAKER Board – ...................... 60
6-29. Printed Wiring Boards – CD MECHANISM Section – . 61
6-30. Schematic Diagram – CD MECHANISM Section – ..... 62
6-31. Printed Wiring Board – POWER Board – ....................... 63
6-32. Schematic Diagram – POWER Board –........................ 64
7. EXPLODEDVIEWS
7-1. Overall Section ................................................................ 78
7-2. Front Panel Section ......................................................... 79
7-3. Chassis Section................................................................ 80
7-4. DVD Mechanism Deck Section-1
(CDM81C-DVBU101) .................................................... 81
7-5. DVD Mechanism Deck Section-2
(CDM81C-DVBU101) .................................................... 82
7-6. DVD Mechanism Deck Section-3
(CDM81C-DVBU101) .................................................... 83
7-7. Base Unit (DVBU101) .................................................... 84
8. ELECTRICAL PARTS LIST .................................. 85

4
HCD-DX375 SECTION 1
SERVICING NOTE
NOTES ON HANDLINGTHE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH
1. Open the cover and turn POWER on with no disc inserted.
2. Confirm that the following operation is performed while
observing the objecting lens.
1) Confirm that laser beam is spread.
2) Up and down motion of the objective lens. (3 times)
DISCTRAY LOCK
The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
Setting Procedure :
1. Press the ?/1 button to turn the set on.
2. Press the [FUNCTION] button to set DVD function.
3. Insert a disc.
4. Press the x button and the A button simultaneously for five
seconds.
5. The message “LOCKED” is displayed and the tray is locked.
Releasing Procedure :
1. Press the x button and the A button simultaneously for five
seconds again.
2. The message “UNLOCKED” is displayed and the tray is
unlocked.
Note 1: When “LOCKED” is displayed, the tray lock is not released by
turning power on/off with the ?/1 button.
Note 2: Incorrect operations may be performed if the test mode ia not
entered properly.
In this case, press the ?/1 button to turn the power off, and
retry to enter the test mode.
Note 3: If the disc tray does not open and the message “LOCKED”
appears, press the x button and the Abutton simultaneously
for seconds or longer.
Then remove your fingers from the above stick and the button.
The message “UNLOCKED” appears for 2 seconds and the disc
tray opens.
Note on DMB12 board replacement
New part of EEP ROM (IC103, IC706) on the DMB12 board cannot be
used. Therefore, if the mounted DMB12 board (A-1148-813-A) is replaced,
exchange new EEP ROM (IC103, IC706) with that used before the
replacement.
When the self-diagnosis function is activated to
prevent the system from malfunctioning, a 5-
character service number (e.g., C 13 50) with a
combination of a letter and 4 digits appears on
the screen and the front panel display. In this
case, check the following table.
When displaying the version
number on the screen
When you turn on the system, the version
number [VER.X.XX] (X is a number) may
appear on the screen. Although this is not a
malfunction and for Sony service use only,
normal system operation will not be possible.
Turn off the system, and then turn on the system
again to operate.
Self-diagnosis Function
(When letters/numbers appear in the
display)
First 3
characters of
the service
number
Cause and/or corrective action
C 13 The disc is dirty.
,Clean the disc with a soft cloth
C 31 The disc is not inserted correctly.
,Restartthesystem, then re-insert
the disc correctly.
E XX
(xx is a number) To prevent a malfunction, the
system has performed the self-
diagnosis function.
,Contact your nearest Sony
dealer or local authorized Sony
service facility and give the 5-
character service number.
Example: E 61 10
C:13:50
VER.X.XX

5
HCD-DX375
CN3002
MAIN BOARD
POWER BOARD
CN902
RED
BLACK
C903
C939
C933 C932
Discharge the charged electricity in capacitors to prevent electric shock as follows
When disassembling the machine, be sure to discharge the charged electricity in the following capacitors.
Use a resistor of 800 ohms, 2 Watts for discharging the following capacitors.
POWER board
C903 : 600V
C932, C933, C939, CN902 : 30V
MAIN board
CN3002 : 30 V
*
Connect the specified resistor
between black and red leads
gear
tweezers
1
Insert tip of tweezers through the hole
of bottom plate, and roate the gear in
the counter-clockwise direction.
DVD lid
tape
2
Attach an adhesive tape on the DVD LID and draw it out.
HOW TO OPEN THE DISC TABLE WHEN POWER SWITCH TURNS OFF

6
HCD-DX375
Fix the capacitors with adhesive agent as follows
Fixing the capacitors with adhesive agent is required by the safety regulation.
Be sure to fix the capacitors with adhesive agent when part or circuit board is replaced.
POWER BOARD
JACK board
CAP (FUNK)
CAP (PLAY)
CAP (AMS)
BUTTON BASE (PLAY)
screws (+BVTP 2.6)
LED board
button (disk),
indicator (disk)
screw (+BVTP 2.6)
s
crews
(+BVTP 2.6)
SW board
BUTTON BASE (POWER)
CAP (POWER)
Precaution when replacing the CAP
Please apply the adhesive agent to the BUTTON BASE (PLAY) when replacing the CAP (PLAY) or CAP (FUNC) or CAP (AMS).
Please apply the adhesive agent to the BUTTON BASE (POWER) when replacing the CAP (POWER).

7
HCD-DX375
PRECAUTION WHEN INSTALLING A NEW OP UNIT /
PRECAUTION BEFORE UNSOLDERING THE STATIC ELECTRICITY
PREVENTION SOLDER BRIDGE
When installing a new OP unit, be sure to connect the flexible printed circuit board first of all before removing the static
electricity prevention solder bridge by unsoldering. Remove the static electricity prevention solder bridge by unsoldering
after the flexible printed circuit board has already been connected.
(Do not remove nor unsolder the solder bridge as long as the OP unit is kept standalone.)
MAIN BOARD
POWER BOARD
Precaution on the connector processing of the POWER board.
AC IN
13
1
12
After twist the harness once,
install the connector.
POWER board
MAIN board
IC504
CN506
CN3002
CN3001
CN902
CN901
CN904
IC941 IC942 IC943
When re-assembling, leave 30 mm between
harnesses A and B for safety.
harnesses A harnesses B
clamp
30mm

8
HCD-DX375
•DMB12 board service position
Remove the DMB12 board once.
Then create the service position.
DMB12 board
DMB12 board

9
HCD-DX375
•POWER board service position
Connect the flexible cable and
harnesses from the front panel assy.
Front panel assy
Inshuration sheet
POWER board
DMB12 board
Remove the DMB12 board and
POWER board once.
Then create the service position.
DMB12 board
POWER board

10
HCD-DX375
•MAIN board service position
Connect the flexible cable and
harnesses from the front panel assy.
Front panel assy
DMB12 board
DMB12 board, bracket (HDMI)
D.C.fan
D.C.fan
MAIN board
MAIN board
SPEAKER board
Remove the DMB12 board ,
bracket (HDMI), D.C.fan and the
MAIN board once.
Then create the service position.
Remove the three connectors of
the SPEAKER board.
Indice
Altri manuali Sony Ricevitore

Sony
Sony HCD-DZ777K Manuale utente

Sony
Sony STR-DG710 Manuale utente

Sony
Sony STR-DG1100 Manuale utente

Sony
Sony STR-DH510 - 10str Hifi Manuale utente

Sony
Sony STR-DG710 Manuale utente

Sony
Sony ST-RDE945 Manuale utente

Sony
Sony STR-DN1040 Guide Manuale utente

Sony
Sony HCD-FLX7D Manuale utente

Sony
Sony STR-DH720 Manuale utente

Sony
Sony XT-XM1 - Xm Satellite Radio Tuner Manuale utente

Sony
Sony STR-DE697 Manuale utente

Sony
Sony STR-DE135 Manuale utente

Sony
Sony HCD-DZ770W Manuale utente

Sony
Sony XAV-V750BT Manuale utente

Sony
Sony STR-K995 Manuale utente

Sony
Sony VAIO VGP-MR100 Manuale utente

Sony
Sony DRC-BT30 Manuale utente

Sony
Sony HBD-E370 Manuale utente

Sony
Sony Betacam BKP-590 Manuale

Sony
Sony HT-DDW1500 Manuale utente





















