Sony STR-DA3300ES - Multi Channel Av Receiver Manuale di servizio
Sony Service Centre (Europe) N.V.
European Service Engineering
Technologielaan 7
B - 1840 Londerzeel
1 / 7
Technical Bulletin
Date Ref. No. Model RASC
11.03.08 08HA004 STR-DA3300ES, STR-DA5300ES AU
Subject IRIS
Slightly Dark Picture C321
SYMPTOM
•The picture becomes slightly dark when a HD video signal in 720p, 1080i, or 1080p is input via component and
connected to the TV via component or HDMI.
•The problem does not occur with:
* HDMI input →HDMI output connection.
* 480i or 480p analog video signal input.
* STR output set up as ”Direct”.
CAUSE
Firmware malfunction.
SOLUTION
Update to the latest version (v1.07) of the Video Processor firmware FAROUDJA as indicated below.
1. Version Number Confirmation
! IMPORTANT !
Check the version number before updating via the “Special Menu”. Do not update the set if the version number is
v1.06 or higher. Since v1.06 does not have the above symptoms, overwriting the firmware will erase some
essential settings.
1-1. Enter the “Special menu” by subsequently pressing the “A.F.D.”, “2CH/A.DIRECT”, “MUSIC” and “MOVIE” key
on the front panel of the amplifier while holding down the “TONE MODE” key’. “MENU SPECIALIZED” is displayed
in the front panel window.
1-2. On the remote commander, press “MENU”. “<<<SPECIAL>>>” will be displayed.
1-3. Press the “Enter” key on the remote commander. “<VIDEO FACTORY MENU>” is displayed.
1-4. Continuously press the “Cursor Down” key on the remote to display the version number.
2 / 7 08HA004
2. Preparation
Make sure to have the below items available.
•PC Communication Jig J-2501-321-A.
•USB Serial Converter (USB-RS232C) or the RS-232C extension cable (straight type).
•DOS/V PC with USB or RS232C port and Windows 2000/XP installed.
•Applicable amplifier (STR-DA3300ES or –DA5300ES).
! CAUTION !
£Before updating, disconnect or power off the power amplifier to avoid noise during updating or prevent the
amplifier from being damaged. Before re-supplying power to the power amplifier, be sure to disconnect the
USB/RS232C cable.
£Before re-supplying power to the power amplifier, be sure to disconnect the USB/RS232C cable. If connected,
symptoms such as abnormal display, abnormal sound and noise may occur when turning on/off the PC power
supply, potentially damaging the power amplifier or the speakers.
£While implementing the Flash overwrite program, never cut off the power supply to the amplifier main unit to
prevent the amplifier flash memory from being damaged.
3. Update Procedure
3-1. Download firmware package
3-1-1. Download the zip file indicated below and attached to this Technical Bulletin.
Date File
March 2008 FAROUDJA107.zip
3-1-2. Unzip this attachment to a dedicated folder on the PC. The following files will be created.
Type File
CGProbe_Redistributable_5.7.0.1.exe
Overwriting program files ISPUtility_2.0.5.0.exe
Latest Flash program file Fli8668_rd3-8668_board_ext.hex
3-2. Connect PC with applicable amplifier
3-2-1. Remove the amplifier case.
3-2-2. Insert the PC Communication Jig cable into the D-VIDEO board “CN3605”. Refer to the picture below for the
precise location of “CN3605”.
3-2-3. Connect the PC communication jig and PC with the USB-RS232C conversion cable (or RS232C extension
cable).
08HA004 3 / 7
3-3. Flash Writer start-up
3-3-1. Power on the applicable amplifier, and boot up the PC.
3-3-2. Double-click the [CGProbe-Redistributable_5.7.0.1.exe] file from the dedicated folder on the PC.
3-3-3. When the installer program starts, click the buttons as scheduled below.
3-3-4. Double-click the [ISPUtility_2.0.5.0.exe] file from the dedicated folder on the PC.
3-3-5. When the installer program starts, click the buttons as scheduled below.
4 / 7 08HA004
3-3-6. Double-click the new icon on the desktop.
3-3-7. The Flash Writer window will be displayed.
3-4. Flash Writer set-up
3-4-1. When the Flash Writer is displayed, click to set the ISP settings as follows.
Connection Serial
Chip FLI8668
Flash device SST39VF320
3-4-2. Click [Settings] to set the serial port that actually connected with the jig. In the example picture this is
“COM4”.
08HA004 5 / 7
3-4-3. Click [Image], and select and open the program file (fli8668_rd3_8668_board_ext.hex) file from the
dedicated folder.
3-4-4. When the Flash Writer setting is completed, in the “File menu” click [Save].
3-4-5. When the [Save File] window is displayed, click the [Save] button, and save as an “.isp” file.
3-5. Implementation and completing of overwriting
3-5-1. Subsequently open the PC folders [C drive] →[Program File] →[Genesis Microchip] →[ISP Utility], and
double-click [FLI8668_SST39VF320.isp].
6 / 7 08HA004
3-5-2. In the [ISP Utility File Dialog Box], click [Start] after confirming that the applicable amplifier is powered on.
3-5-3. The message “Entering debug mode. Please reset the board and press OK” will be displayed. Click [OK].
The upgrade will start.
3-5-4. It takes about 2 minutes to upgrade. Make sure not to touch the applicable amplifier and PC during writing.
The message “ISP successful” will be displayed when the writing is completed normally. Click the [ ] button on
the top right of the screen to close the program.
3-5-5. Power off the applicable amplifier, and disconnect the cable of the PC Communication Jig.
NOTE
If multiple upgrades need to be performed, only steps 3.1 and 3.5 of this procedure are to be repeated.
4. Version Number Confirmation
Refer to step 1 of this procedure for further details.
******
Amplifier Initialization
Initialize the amplifier by performing the steps below.
1. Press [POWER] to turn off the amplifier.
2. Press [POWER] to turn on while holding down [TONE MODE] and [DMPORT] on the front panel.
3. “MEMORY CLEARING” appears on the display for a while. All memory is reset to the factory settings.
£Do not use a “Super reset” in the “Special Menu Mode”. If a “Super reset” is performed, also an “up convert
signal level adjustment” will be initialized.
08HA004 7 / 7
Troubleshooting
•In case of “Communication Error” after pressing the [Start] button, confirm the below points.
* Is the power on to the applicable amplifier?
* Are the cables connected firmly?
* Are the correct RS232C extension cables used? Always use a straight type cable.
* Is the cable connected tot the correct COM PORT number?
* Is the connected COM PORT available at PC side? Check whether the installed modem is equipped with the
port or not.
•Make sure to copy the Flash Overwrite program and the latest Flash program file to the hard disk before use.
Booting up from the floppy disk may cause a failure due to a slow access speed.
•In case of unsuccessful overwriting, press the [Start] button of the FAOUDJA update, and start overwriting
again from the beginning.
•Overwriting may fail if any other Windows applications are run during the operation.
APPLICABLE SERIAL NUMBERS
Model Destination Colour
Serial number
UK Black 6600001~6600219
Continental Europe Silver 5500001~5501370
Continental Europe Black 5500001~5501393
Europe Silver 5500001~5503535
STR-DA3300ES
Europe Black 5500001~5503540
UK / 6600001~6600157
Continental Europe / 5500001~5501773
Europe Silver 5500001~5503081
STR-DA5300ES
Europe Black 5500001~5503286
Altri manuali per STR-DA3300ES - Multi Channel Av Receiver
9
Questo manuale è adatto per i seguenti modelli
1
Altri manuali Sony Ricevitore
Sony
Sony STR-DA3200ES - Es Receiver Manuale utente
Sony
Sony STR-DA4ES - Fm Stereo/fm-am Receiver Manuale utente
Sony
Sony AC-U50AG Manuale utente
Sony
Sony ICF-M350V Manuale utente
Sony
Sony HCD-FX888K Istruzioni per il montaggio
Sony
Sony STR-DE885 Manuale utente
Sony
Sony DRN-XM01C Manuale utente
Sony
Sony HCD-DZ230 Manuale utente
Sony
Sony STR-DG700 Manuale utente
Sony
Sony STR-ZA1100ES Guida utente
Sony
Sony HBD-TZ210 Manuale utente
Sony
Sony STR-GX9O0ES Manuale utente
Sony
Sony HCD-FC7 - System Components Manuale utente
Sony
Sony IFT-R20 Manuale utente
Sony
Sony STR-DA1000ES Manuale del proprietario
Sony
Sony HCD-DZ150K Manuale utente
Sony
Sony STR-DG910 Manuale utente
Sony
Sony DVX 11B Manuale utente
Sony
Sony STR-K1600 Manuale utente
Sony
Sony M2 MSAC-MMD Manuale utente
