Spa Electrics RETRO Series Istruzioni operative
AQUA/LAMP REPLACEMENT
2
3
4
5
6
7
10
12
13
15
18
CONTENTS
PRODUCT SUPPORT & INFORMATION
CANADA / NTH AMERICA INTERNATIONAL
Select Pool Products Spa Electrics PTY LTD
Email: info@spaelectrics.com.au
www.spaelectrics.comwww.selectpoolproducts.ca
Tel: 1-855-881-0889 Tel: +61 3 9793 2299
Email: info@selectpoolproducts.ca
1
READ THIS FIRST / PRODUCT WARNINGS
TOOLS REQUIRED / WINTERISATION
INCLUDED PARTS
BEFORE YOU START
EXISTING LIGHT REMOVAL / CABLE PREPERATION
CABLE JOINER INSTALLATION
LIGHT INSTALLATION
LIGHT REMOVAL / WINTERISATION
MULTI PLUS SETUP
MULTI PLUS - MANUAL OPERATION
CERTIFICATION & COMPLIANCE
Congratulations on your purchase of a Spa Electrics RETRO Series pool light, for safe
and proper installation, please read the installation manual carefully prior to product
installation.
For safe & proper installation, use only parts (screws, plugs, sealant etc) provided.
The RETRO Series EMRX Light must be water cooled at all times. DO NOT switch the
light on until installation is complete and the light is fully submerged in water.
Ensure sufficient cable is coiled behind the light to allow for servicing
Ensure only circular cable not exceeding 14mm diameter is connected to the
supplied cable joiner. The use of Figure 8 or non circular cable will prevent correct
sealing & will void the product warranty.
The RETRO Series EMRX Light does not contain any user serviceable parts, opening
the light will void the product warranty.
Pool chemicals & PH levels: Due to the corrosive nature of unbalanced pool chemi-
cals, Spa Electrics strongly recommends that your pool water is balanced prior to
installing your pool Lights or any plastic or stainless steel components, and tested
weekly to maintain these levels. pH levels should be maintained between 7.2- 7.6 at
all times to ensure the longevity of these components.
Failure to do so can result in chemical damage to the light housing and
pool fittings, including stainless steel components.
Please note: Lights or components found to have excessive chemical
damage will not be covered under our manufacturer’s warranty policy
READ THIS FIRST
WARNING
The RETRO Series light must only be used with a UL listed 12V AC Class 2 power supply or a
power source intended for swimming pool use (not included).
Minimum power source wattage requirement - 15 Watts per light.
ELECTRICAL SUPPLY NOTICE
2
TOOLS REQUIRED
Side cutters / Pliers
Small flat-blade screwdriver (supplied)
24mm / 29mm spanner (supplied)
• The use of power tools during installation is not recommended as these
devices can cause faults and damage to light components.
• All installation steps should be carried out with manual tools only.
• The enclosed images are for illustrative purposes only. Appearances of parts
and assemblies may vary from the enclosed illustrations.
• Please contact your reseller if you have any questions regarding the correct
installation of this product.
IMPORTANT NOTES
WINTERIZATION
• All RETRO Series lights must be removed from niche (Pg.12) and lowered to
pool floor during periods of pool water freezing.
• Pre-existing niches should be adequately protected during winter months as
per manufacturers recommendations.
• Consult your local pool professional for complete pool winterization process.
3
1 X RETRO LIGHT
PLUG CONNECTION
UNDERWATER
CABLE JOINER
INCLUDED PARTS
AQUA/LAMP
ADAPTOR PLATE
SCREW DRIVER SPANNER
18” OF 18AWG CABLE
24
29
PREASSEMBLED
4
ON
OFF
BEFORE YOU START
1ISOLATE POOL LIGHTS
2CHECK TRANSFORMER
EXISTING TRANSFORMER
MUST BE:
EXISTING TRANSFORMER
MUST NOT BE:
MIN. 15 WATT (PER LIGHT)
IN GOOD WORKING ORDER
DC OR ‘LED DRIVER’
ELECTRONIC OR SWITCH MODE
WEATHER DAMAGED OR IN
OTHERWISE POOR CONDITION
UL LISTED 12V AC CLASS 2 POWER
SUPPLY OR A POWER SOURCE
INTENDED FOR SWIMMING POOL USE
ENSURE SYSTEM IS SAFELY
ISOLATED DURING THE
INSTALLATION PROCESS.
IF IN DOUBT; CONTACT YOUR
ELECTRCIAL CONTRACTOR FOR
ASSISTANCE.
5
REMOVAL OF EXISTING LIGHT
REMOVE EXISTING POOL
LIGHT FROM POOL WALL BY
ROTATING CENTRE LIGHT FITTING
COUNTER-CLOCKWISE.
DISCONNECT CABLE TO
POOL LIGHT, ENSURING
ENOUGH CABLE LENGTH
REMAINS ABOVE THE
NOMINAL WATER LEVEL TO
ENSURE SERVICE ACCESS.
1.
1.
2.
STRIP CABLE OUTER AND
INNER SHEATHS TO THE
BELOW LENGTH.
1REMOVE EXISTING LIGHT
2PREPARING EXISTING CABLE
10mm
EXISTING CABLE
10mm
NICHE LIGHT
1
2
6
LOOSEN OUTER CABLE
GLAND NUTS.
LOOSEN AND REMOVE
BOTH THREADED HEX
NUTS USING 29mm
SPANNER.
PLACE CABLE GLAND NUT
AND THREADED HEX NUT
OVER RETRO LIGHT CABLE.
INSTALLING CABLE JOINER
1OPEN CABLE JOINER
2CONNECT RETRO LIGHT CABLE
1
1
2
2
24mm
RETRO
LIGHT
EXISTING
CABLE
29mm
IMPORTANT
CONNECT WIRES TO
TERMINAL BLOCK USING
FLAT BLADE SCREW
DRIVER.
7
INSTALLING CABLE JOINER
SLIDE THREADED HEX NUT
OVER TERMINAL BLOCK.
ENSURING CABLE SHEATH
EXTENDS INSIDE THE
ASSEMBLY.
3
TIGHTEN CABLE GLAND NUT
USING 24mm SPANNER.
4
ATTACH MAIN BODY AND
TIGHTEN USING 29mm
SPANNER.
5
IMPORTANT
DO NOT OVER TIGHTEN
IMPORTANT
DO NOT OVER TIGHTEN
8
INSTALLING CABLE JOINER
3CONNECTING TO EXISTING CABLE
SLIDE THREADED HEX NUT OVER
TERMINAL BLOCK AND TIGHTEN ONTO
MAIN BODY USING 29mm SPANNER.
IMPORTANT
DO NOT OVER TIGHTEN
IMPORTANT
DO NOT OVER TIGHTEN
PLACE CABLE GLAND NUT AND THREADED
HEX NUT OVER EXISTING LIGHT CABLE.
1
1
2
3
TIGHTEN CABLE GLAND NUT
USING 29mm SPANNER.
4
2CONNECT WIRES TO TERMINAL BLOCK
USING FLAT BLADE SCREW DRIVER.
9
Questo manuale è adatto per i seguenti modelli
4
Altri manuali Spa Electrics Illuminazione per piscine
