Speco O4B6M Manuale utente
Quick Start Guide
O4B6M
1Warning and Caution
■ If the product does not work properly, please contact your
dealer or the nearest service center. Never attempt to disassemble
the camera yourself. Any unauthorized changes or modifications
could void the warranty.
■ Do not allow water or liquid intrusion into the camera.
■ All installation and operation here should conform to local
electrical safety codes. Make sure the device is firmly installed
on the wall or ceiling.
■ Do not use camera beyond specified voltage range.
■ Do not drop the camera or subject it to physical shock.
■ Avoid touching the camera lens.
■ If cleaning is necessary, please use cleaning cloth to wipe it
gently.
■ Do not aim the camera at the sun or extremely bright light
sources.
■ Do not place the camera in extremely hot or cold environments
and dusty and damp locations . Do not expose it to highly
electromagnetic radiation.
■ Do not block any ventilations.
Package
2
Overview
3 Overview
3
Camera Quick start guide
CD Plastic plug ×4
Drill template
Rubber plug
CVBS&DC
IN cables
Screwdriver Junction box
4 tapping screws PA4×25
1 machine screw PWM3×5
8
9
10
2
3
4
5
6
1
7
MIC input (3.5mm)
Line out (3.5mm)
Micro SD card slot
Reset hole
CVBS/DC IN port for testing
Alarm input/output
RS485 cable
Ethernet connector
DC power connector
1
2
3
5
7
9
4
6
8
10
Analog ouput (BNC)
* 1 It is recommended to install the security cap for outdoor installations.
* 2 DC 12V power supply is not required if a PoE switch or injector is used to power
the camera.
► Connecting Network Cable
① Loosen the nut from the main element.
② Run the network cable (without RJ 45 connector) through both
elements. Then crimp the cable with RJ 45 connector.
③ Connect the cable to the hermetic connector. Then tighten the nut
and the main cover.
2
13
ALM-COM
ALM-NO
ALM-IN
ALM-GND
RS485T+
RS485T-
Security Cap
Installation
4
* Before you start, please make sure that the wall or ceiling is strong enough
to withstand three times the weight of the camera.
① Install junction box onto the wall by using the screws provided.
② Connect the cables and mount the rubber plug to the gap of the
mounting base. Then fasten the camera onto the junction box.
Rubber Plug
③Three-axis Adjustment-Before adjustment, preview the image of the
camera on a monitor and then adjust the camera according to the figure
below to get an optimum angle.
Tilt 90°
Pan 360°
Rotate
360°
Web Operation and Login
5
● Operation
IP Scanner can search for the device on the local network.
① Make sure that the camera and the PC are connected to the same
local network. The camera is set to DHCP by default.
② Install IP Scanner from the CD and run it after installation.
③ In the device list, you can view the IP address, model number, and
MAC address of each device. Select the applicable device and double
click to open up the web viewer. You can also manually enter the IP
address in the address bar of the web browser.
The login interface is shown above. Default user name is admin and
password is 1234. After logging in, follow directions to install
applicable plugins.
Indice
Altri manuali Speco Telecamera di sicurezza
Speco
Speco PROVIDEO CVC-190 Manuale utente
Speco
Speco O5B2 Manuale utente
Speco
Speco O6MDP3 Manuale utente
Speco
Speco CVC-745TP Manuale utente
Speco
Speco ONSIP O2D3 Manuale utente
Speco
Speco INTENSIFIER CVC6246IHR Manuale utente
Speco
Speco O4B6 Manuale utente
Speco
Speco O4D6WM Manuale utente
Speco
Speco ONSIP 02S1 Manuale utente
Speco
Speco O4VT1 Manuale utente
Speco
Speco ONSIP O2B5 Manuale utente
Speco
Speco HT - INTB8/9/10 Manuale utente
Speco
Speco VLD9 Manuale utente
Speco
Speco CVC-614C Manuale utente
Speco
Speco O2VD2 Manuale utente
Speco
Speco ONSIP O2IR56B1 Manuale utente
Speco
Speco VLED24T3W Series Manuale utente
Speco
Speco HTD8FFI Manuale utente
Speco
Speco VL-6WMTDV Manuale utente
Speco
Speco O5T2 Manuale utente
