Speco O84S Manuale utente

Indice

Altri manuali Speco Telecamera di sicurezza

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

Vivotek

Vivotek FD9389-EHV-v2 Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Vitek

Vitek VTC-C544 Manuale utente

Quick Start Guide

O84S

Welcome

Thank you for purchasing this network camera!

This owner's manual is designed to be a reference tool for your system.

Please read this manual carefully before operating the unit and retain it for future reference.

Should you require any technical assistance, contact Speco Technologies Tech Support at

1-800-645-5516

1. Electrical safety

All installation and operation here should conform to local electrical safety codes.

Use included power supply only.

Please note: Do not connect two power supplying sources to the device at the same time;

it may result in device damage! The product must be grounded to reduce the risk of

electric shock.

Improper handling and/or installation could run the risk of fire or electrical shock.

2. Environment

Heavy stress, violent vibration or exposure to water is not allowed during transportation,

storage and installation.

This product should be installed in a cool, dry place away from direct sunlight and heat

sources.

Do not install the product in extreme temperature conditions.

Do not expose the camera to electromagnetic radiation. Otherwise it may result in CMOS

sensor failure.

Do not block any ventilation openings.

Do not allow water and liquid intrusion into the camera.

3. Operation and Daily Maintenance

Please shut down the device and then unplug the power cable before you begin any

maintenance work.

Do not touch the CMOS sensor optic component. You can use a blower to clean the dust on

the lens surface.

Always use the dry soft cloth to clean the device. If there is too much dust, use a cloth

Important Safeguards and Warning

Warning

Statement

This camera should be installed by qualified personnel only.

All the examination and repair work should be done by qualified personnel.

Any unauthorized changes or modifications could void the warranty.

.

This guide is for reference only.

Product, manuals and specifications may be modified without prior notice. Speco

Technologies reserves the right to modify these without notice and without incurring

any obligation.

Speco Technologies is not liable for any loss caused by improper operation.

Note:

Before installation, check the package and make sure that all components are included.

Contact your rep or Speco customer service department immediately if something is

broken or missing in the package.

dampened with a small quantity of neutral detergent. Finally use the dry cloth to clean

the device.

Please use a professional optical cleaning method to clean the enclosure. Improper enclosure

cleaning (such as using cloth) may result in poor IR functionality and/or IR reflection.

The grounding holes of the product are recommended to be grounded to further enhance

the reliability of the camera.

Overview

3 Overview

1

1 Ethernet Connector(PoE)

2 MIC-Audio Input

3 HP-Audio Output

4 Alarm Input/Output

5 Power Jack

6 Ground

7 Reset

8 Micro SD slot

1

2

3

4

5

6

ALARM

4 3 2 1

78

Cover

RJ 45

HP

MIC

1-AL ARM

2-AL ARM-COM

3-AL ARM-GND

4-AL ARM-IN1

-OPE N

Power Jack

Ground

ALARM

4 3 2 1

Installation

2

This camera can be installed in different way. Please select a way to install

as needed. The following instructions are for reference only. Please make

sure the installation surface is strong enough to bear the dome camera’s

weight and the camera is powered off during installation.

As dirt, dust, or fingerprints on the bubble will reduce the clarity of the

image, please keep it clean in the course of installing or using but DO NOT

directly touch or wipe it.

Memory Card Installation

1. Unscrew the cover of the memory card.

2. Insert a micro SD card and then install the cover back with the screws.

Pole Mounting

1. Install the bracket to the pole according to the following picture.

It’s recommended that this panoramic camera is mounted 1 m (3.2feet) away

from the pole, to avoid the IR light beam reflected from the

pole into the camera lens, resulting in image blur.

The recommended installation height ranges from 4m to 8m(13.1ft~26.2ft).

Screws

Trim cover Bubble

2. Pull out of the trim cover of the bubble. Then unscrew the bubble as

shown below.

3.2ft

13.1ft~26.2ft

3. Connect the relevant cables.

① Loosen the nut from the main element.

② Run the network cable (without RJ 45 connector) through the

both elements. Then crimp the cable with RJ 45 connector.

③ Connect the cable to the hermetic connector. Then tighten the

nut and the main cover.

①②③

Make sure the side with the sign faces

people/vehicle flow when installing.

4. Attach the camera to the bracket with screws.

5. Adjust the view angle of each lens module. Before adjustment, please

view the image on a monitor.

Note: This camera has four 4mm lens modules, each of them covers 90

360

° horizontal

field of view. Thus, it totally can cover ° panoramic view. The camera has adjusted

the lens modules for best and large view angle before delivery, but you can still

re-adjust the lens angle as needed. Each lens module could manually slide 0~120°,

and move 45°~75° vertically.

45 ~75°°

0°~120°

6. Install the bubble back to its original position with four screws. Then put

the trim cover onto the bubble to finish the installation.

Indoor Mounting

1. Install the ceiling mounting bracket according to the following

diagram. (ceiling mounting bracket included)

It is recommended to install the camera in the center of the ceiling.

2. Mount the adapter tube to the bracket and fix it with a screw.

3. Secure the ceiling mounting bracket to the ceiling.

4. Connect cables and then hook the safety wire to the adapter stem.

5. Secure the camera to the adapter tube with screws firmly.

Adapter tube

Note: for the lens adjustment, please refer to the pole mounting for details.

Web Operation and Login

3

IP Scanner can search for the device on the local network.