Spectron IT-12-Exd Manuale utente

SPEC.425411.300.100 RE

Agreed:

FSUE “VNIIFTRI”

OS VSI “VNIIFTRI”

Operating Manual

TEST TRANSMITTER

EXPLOSION-PROOF

IT-12-Exd

2017

ATTENTION!

Before starting to operate IT-12-Exd explosion-proof test transmitter, carefully

read the Operating Manual.

During the testing of detectors it is compulsory to switch off firefighting

equipment.

1. DESCRIPTION

The purpose of IT-12-Exd explosion-proof test transmitter (hereinafter “the

transmitter”) is remote testing of operational performance of Spectron-601-Exd

series flame detectors issued on 01.01.2017 or later.

The transmitter is produced in compliance with requirements to ex-proof

equipment of subgroups IIA, IIB, IIC according to TR CU 012/2011, GOST

30852.0 (IEC 60079-0), GOST 30852.1 (IEC 60079-1) and complies with

1ExdIICT6 explosion-proof marking.

The transmitter is designed to be used in indoors and outdoors explosion-hazard

areas according to the classification in chapter 7.3. of Electrical Installation Code,

GOST 30852.9, GOST 30852.13 and other directives that outline the application

of equipment in explosion-hazard areas. The transmitter features a D16 grade

aluminum body and has IP68 Ingress Protection Degree from environmental

impact. The transmitter’s body is covered with black powder paint.

2. TECHNICAL FEATURES

Table 1

Features

Value

Power voltage (2 batteries of 3.75V), V

6-8

Consumed current, not more than, mA

100

Distance to sensitive element of detector, m

Shell protection level, IP

Operating temperature, °С

–40 ÷ +60

Relative air humidity, %

100% at +40°С

Transportation and storage temperature, °С

–40 ÷ +60

Run time, h

50*

Weight, kg

1.1

* - at operating temperature below 0°С the transmitter’s run time may reduce.

Fig.1 - Transmitter dimensions

3. USAGE INFORMATION

3.1. DESIGN AND FUNCTION

The transmitter includes an aluminum body that consists of a reflector, an

electronic board with light-emitting diodes, a mode selection switch and a battery

compartment cover –see Fig. 2. The battery compartment is filled with

compound.

The transmitter has the following operating modes:

•testing the detector’s switching into the Fire mode

•testing the detector’s switching into the Failure mode testing glass

dustiness - in the automatic mode.

ATTENTION!

During the testing of detectors it is compulsory to switch off firefighting

equipment.

Testing of the detector should be performed from the distance of 25 m maximum.

During the testing, the transmitter’s axis should be aligned as much as possible

with the direction to the detector. Get as close to the detector as possible if

neighboring detectors are installed in close proximity to the tested one.

3.2. FIRE MODE

Use the condition of the light-emitting diode indicator to make sure that the tested

detector is in the stand-by mode.

Turn the transmitter on by turning the switch to align the marking on the body

with F1 or F2 or F3 signage (Fig. 2); the light-emitting diodes should be blinking

at this time. Point the transmitter in the direction of the detector’s front-face

surface. Hold the transmitter until the detector goes into the Fire mode. At this

time the detector’s indicator shall switch to continuous lighting mode. FIRE relay

is off.

ATTENTION!

Do not hold the operating transmitter for longer than 28 seconds: after this time

the FIRE relay shall activate in the detector.

To turn the transmitter off, turn the switch until it clicks and the marking on the

body is not aligned with F1, F2, F3 or F4 signage; the light-emitting diodes should

go out at this time (the switch is in the OFF position between F modes).

After you turn the transmitter off, the detector will automatically go into the

Stand-by mode.

If glass dustiness has reached a critical level, the detector will go into the Failure

mode during the Fire mode testing, activating FAILURE relay and the

corresponding light-emitting diode indication.

3.3. FAILURE MODE

Use the condition of the light-emitting diode indicator to make sure that the tested

detector is in the stand-by mode.

Turn the transmitter on by turning the switch to align the marking on the body

with F4 signage (Fig. 2); the light-emitting diodes should be blinking at this time.

Point the transmitter in the direction of the detector’s front-face surface. Hold the

transmitter until the detector goes into the Failure mode. At this time the

detector’s indicator shall switch into the frequent blinking mode.

FAILURE relay is off.

ATTENTION!

Do not hold the operating transmitter for longer than 28 seconds: after this time

the FAILURE relay shall activate in the detector.

To turn the transmitter off, turn the switch until it clicks and the marking on the

body is not aligned with F1, F2, F3 or F4 signage; the light-emitting diodes should

go out at this time (the switch is in the OFF position between F modes).

After you turn the transmitter off, the detector will automatically go into the

Stand-by mode.

Fig. 2 - Transmitter appearance

3.4. BATTERY CHARGING ATTENTION!

Only charge batteries outside of explosion-hazard areas.

To charge batteries:

1. Make sure the transmitter is off (the marking on the body is not aligned with

F1, F2, F3 or F4 signage on the switch, the light-emitting diodes are off). 2.

Make sure the battery’s temperature is from 0°С to +45°С.

3. Unscrew the battery compartment cover, see Fig.2.

4. Connect the charging adaptor (included in the delivery package) for 220V,

50Hz network to the transmitter’s slot. The batteries need at least 2.5 hours

to charge.

5. Disconnect the charging adaptor and screw the battery compartment cover

shut with a 19mm wrench until the sealing ring is compressed.

NOTE

Charge the batteries before using the transmitter.

During long storage, battery capacity is reduced due to standing loss.

4. SAFE OPERATION REQUIREMENTS

Assembly and operation shall be performed in compliance with Operating Manual

requirements, chapter 7.3 of “Electric Installation Code”, GOST 30852.0, GOST

30852.1.

Battery

compartment cover

Switch

Marking

Board with

LEDs

Reflector

Observance of safety rules is a necessary requirement for safe operation and

functioning of the transmitter.

Operation of the transmitter should be performed by authorized personnel that

received training, an assessment by a certification committee and got acquainted

with the Operating Manual and instructed on safe service and maintenance.

All maintenance work on the transmitter associated with removing the battery

compartment cover must be performed only outside of explosion-hazard areas.

Maintenance personnel shall be responsible for occupational safety.

Explosion safety of the transmitter is provided by:

•type “d” ex-proof shell;

•in compliance with GOST 30852.1 conducting parts and sparking parts are

installed inside an ex-proof body that is resistant to explosion pressure and,

along with protection means, prevents explosion transfer to the explosion-

hazard environment; the battery compartment cover is threaded to the

body.

•in normal operating mode, the heating temperature of the outer surface does

not exceed temperatures recommended for electrical equipment of the

corresponding temperature class, in compliance with GOST 30852.0;

•the body’s threaded joint is covered with TSIATIM-221 GOST 9433

lubricant;

•the body corresponds to the high degree of mechanic stress in compliance

with GOST 30852.0.

5. TROUBLESHOOTING ATTENTION!

The transmitter is not designed to have its components repaired by the user.

If the transmitter is on but its light-emitting diodes are not luminescent you should

charge the batteries according to section 3.2 - Battery Charging.

If light-emitting diodes did not resume luminescence after the batteries have been

charged please contact NPO Spectron Service Desk.

6. REPAIR AND RETURN OF THE DEVICE

The transmitter is not intended to be repaired by the user on site. If any problem

occurs, please follow section 4 - Troubleshooting. If you identify any defects or

failures that occurred through manufacturer’s fault, the user unilaterally creates a

failure certificate with defect description. The transmitter along with the product

passport and certificate shall be returned to the manufacturer.

Transmitter’s transportation packaging is described in section 7 - Transportation

and storage. If the transmitter is returned to the manufacturer, it should be sent to:

2D Lenin St., Beryozovsky, Sverdlovsk Oblast, 623700, Russia, tel.:

(343)379-07-95.

7. MANUFACTURER’S WARRANTY

The transmitter’s average service life is at least 10 years (this does not apply to the

batteries included in the transmitter).

The transmitter’s warranty life is 12 months from the date of sale.

Get an additional free 24-month warranty through WARRANTY EXTENSION

service at http://spectron-ops.ru/.

Warranty repairs in compliance with GOST R IEC 60079-19 and transmitter

replacement shall be performed by the manufacturer only if the user follows all

transportation, storage and operation requirements.

The manufacturer shall not accept any claims after the warranty period expires, if

the product passport for the transmitter is not provided or the Operating Manual is

not followed.

8. TRANSPORTATION AND STORAGE

For transportation the transmitter should be packed in the factory package or a

dimensions-suitable box; it must be protected with bubble wrap, polyethylene

foam or another shock absorbing material. If several items are packed in one box,

spacers must be placed between them.

It is allowed to transport the transmitter to any distance by any type of transport.

Protection of the transport package from precipitation shall be provided for the

period of transportation.

During loading and unloading and during transportation the transmitter should not

be exposed to shocks or atmospheric precipitation. During transportation the box

with the transmitter should be placed in such a manner as to prevent its

uncontrolled movement.

9. DELIVERY PACKAGE

The transmitter’s scope of supply includes:

•transmitter .............................................................................................. 1 pc.;

•charging adapter for 220V, 50Hz network ............................................ 1 pc.;

•Operating manual SPEC.425411.300.100 RE ....................................... 1 pc.;

•passport SPEC.425411.300.100 PS ....................................................... 1 pc.

MANUFACTURER’S ADDRESS

Russia,

2D, Lenin St., Beryozovsky, Sverdlovsk Oblast, 623700;

tel. (343)379-07-95.

[email protected] www.spectron-ops.ru

Indice

Altri manuali Spectron Trasmettitore

Spectron

Spectron IT-12-Exd Manuale utente

Manuali Trasmettitore popolari di altre marche

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuale del proprietario

Honeywell

Honeywell 5816WMBR Manuale utente

Kamstrup

Kamstrup READy MTU Istruzioni operative

Omega

Omega ZW Series Manuale utente

ABB

ABB Field 264H Guida

Alinco

Alinco DJ-V17T Manuale utente

Dejero

Dejero EnGo 3x Manuale utente

Rosemount

Rosemount 4600 Manuale utente

Speaka Professional

Speaka Professional 2342740 Manuale utente

trubomat

trubomat GAB 1000 Manuale utente

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuale utente

Rondish

Rondish UT-11 Manuale utente

MG 10JRE Manuale utente

Burkert

Burkert 8177 Manuale utente

Firetide

Firetide HotPort 3203 Manuale

Tele Radio

Tele Radio T9-02 Manuale utente

Rotronic

Rotronic HygroFlex HF3 Series Manuale utente

Jamara

Jamara FCX6 Pro Tel Manuale utente