Spot-on SRL300G Manuale utente
SRL300R/G Spot-On Rotary Laser 300 Red/Green
Operating Instructions
Self-levelling Automatic Horizontal and Vertical Rotary Laser
1
Maintenance and Safety
•While the instrument is operating, be careful not to expose your eyes to the laser beam. Direct
exposure to a laser beam for a long time may be hazardous to your eyes. The laser beam is
equivalent to a class II .
•Operate this laser so that the laser beam plane avoids impact on the eyes of vehicle drivers or
pedestrians.
•Do not try to dismantle the instrument. Have it repaired by your dealer or supplier. Dismantling yourself
may worsen the problem or void your warranty.
•When attaching the instrument to a tripod, make sure the instrument is securely fixed. The tripod leg
clamps should be securely fastened. If not securely fastened or tightened, the main unit could fall off
or the tripod could fall over.
•The laser should not be stored or used in extreme temperature or during rapid temperature change.
The laser may not function properly if used out of the ambient temperature range.
•Store inside the carry case and place in a dry area not subject to vibration, dust or high moisture.
•If the storage temperature and ambient temperature for usage vary significantly, leave the laser in its
case until it can adjust to the ambient temperature.
•The laser should be transported or carried carefully to avoid impact or vibration.
•The laser should be stored in the carry case and packed with cushioning material. Always handle the
laser with care.
2
1.What is included with your SRL300R
3
Your SRL300R set includes the following parts:-
Rotary Laser (SRL300R)
Receiver (FRD300) and Staff Clamp
Remote Control (FRR200)
Charger (FC100-UK)
Magnetic Laser Target (Red)
Laser Enhancemant Glasses (Red)
Hard CarryCase with Foam Insert
Please contact your supplier if any of the above parts are missing.
4
2. Find your way around the HV/HVG
Handle
Optical Glass
Light House
Control Panel
Base
Rotating Head
Plumb Up Beam
5
2.1 Control Panel
Switch ON/OFF
Left Spin
Right Spin
Direction Scan
H.I Alert
Head Speed
6
2.2 Utilities of Panel
(1) Switch ON/OFF: Powers the laser up or down.
(2) Power indicator: When the light is on, the instrument is on.
(3) Head speed indicator: Indicated the current rotational speed of the unit buy the speed that the LED flashes.
(4)Head speed: Press this button to cycle through the various rotational speeds from 0 - 600rpm.
(5) Tilt/H.I alert: Enabling this mode warns the user if the laser level has been jolted.
(6) Tilt indicator: When the light is blinking slowly, the laser is in H.I alert mode. When the light is blinking
quickly, the laser level will not level as it has been jolted.
(7) Directional scanning: Circling knob.Angle of scanning includes 5 levels: 0-10°-45° -90°-180°
(8) Left-spinning: Used when is scan mode to rotate the lasers head counterclockwise.
(9) Right-spinning: Used when is scan mode to rotate the lasers head clockwise.
7
3. Directions:
3.1 Battery Installation
The SRL300 is supplied with a rechargeable Ni-MH battery pack that is located in the base of the unit.
It is recommended that the battery pack be completely charged before use as the SRL300 battery pack does not
come pre-charged and charging the unit while it is operating increases the charging time. The charging time when
the unit is turned off is approximately 8 hours. The operating time for the SRL300 with a new battery pack that is
at full charge is approximately 50 hours however this will decrease over time as the battery pack ages and due to
the number of charges / discharges that the battery pack has in its lifetime. Operating time may decrease and
charging time may increase based on changes in temperature where the unit is being either stored or operated.
The SRL300 is supplied with a battery charger / power adaptor in the carry case. When the SRL300 is low on
power the power indicator light will begin to flash indicating that the battery pack should be recharged as soon as
possible.
Plug Hole
8
To charge the SRL300, insert the battery charger / power adaptor into the port on the battery pack. The light on
the battery charger /power adaptor has three stages:
- Red (Flashing) –Charger and battery are not connected.
- Red (Constant) –Battery is charging.
- Green (Constant) –Battery is charged.
Notices:
(1) Using the standard rechargeable batteries of the instrument, recharging will be finished
within 8 hours.(4x5000mAh Ni-Mh batteries)
(2) Power required for the charger: Frequency: 50-60HZ; Voltage: 85-265V.
(3) Charging and using of the instrument can progress simultaneously.
(4) If keeping the instrument in storage (or Leave the instrument unused for a long time), the
batteries (dry battery or rechargeable battery) needs to be taken out.
(5) Brand-new rechargeable batteries or long-time unused rechargeable batteries need to be
recharged and discharged three times to attain the capacity required.
9
3.2 Operations
3.2.1 Set Up (Horizontal Mode)
1. Attach the SRL300 to a tripod that is as level as possible or place on a flat level surface. Make sure that the
SL300 is aligned correctly on the tripod and securely tightened in position or the unit may move during use.
2. Press the Power button to turn the SRL300 on and allow it to begin its leveling process. The Power indicator
light will be shown indicating that the unit is on and operating.
3. Once the SRL300 has completed its self-leveling process the laser will begin to rotate. Please note that the
leveling time can vary based on the angle that the laser is positioned from previous use and any disturbances that
the unit may be sustaining.
4. If the SRL300 is outside of its leveling range the laser beam will flash continuously indicating that it is unable
to level. Please do not stare directly into the laser beam.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Spot-on Livello laser
