ST STM32 Nucleo Manuale utente

April 2011 Doc ID 18303 Rev 1 1/24

UM1038

User manual

Hardware interconnection of the STM32™,

SPEAr™3xx, and ST75xx

1 Introduction

This user manual describes the STarGrid powerline modem, the latest family of powerline

modems from STMicroelectronics™. The powerline modem itself, although a powerful

device, always needs an external superior system which it uses in order to exchange

information with another node, where another powerline modem and superior system can

be found.

There are various superior systems and this document deals with the hardware

interconnection to powerline modems. These superior systems are from very simple 32-bit

microcontroller boards running standalone firmware to very complex 32-bit micro processor

units running operating systems. This document describes the possible ways of

interconnection and available HW and SW tools for building the system consisting of the

STM32 or SPEAr3xx, and powerline communication coming from the ST7570, 80, and 90

STarGrid family.

The related demonstration boards are:

■STEVAL-PCC012V1

■STM3210C-EVAL

■EVALSPEAr310

■EVALSPEAr320PLC

■EVALSPEAr320HMI

■EVALST7570, 7570-1 KIT, 7580-1, 7590-1.

www.st.com

Contents UM1038

2/24 Doc ID 18303 Rev 1

Contents

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

2 STM32 (STEVAL-PCC012V1) and EVALST7570-1 . . . . . . . . . . . . . . . . . . 5

3 STM32 (STEVAL-PCC012V1) and EVALST7590-1 . . . . . . . . . . . . . . . . . . 7

4 STM32 (STM3210C-EVAL) + EVALST7590-1 . . . . . . . . . . . . . . . . . . . . . . 9

5 SPEAr320 and EVALST7590-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

6 EVALSPEAr310 and EVALST7590-1 via RS232 . . . . . . . . . . . . . . . . . . 11

7 SPEAr3xx and ST7570, ST7580, ST7590 via USB . . . . . . . . . . . . . . . . 13

8 EVALSPEAr320HMI and ST7570, ST7580, ST7590 via UART . . . . . . . 14

Appendix A HW images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

A.1 STM32 (STEVAL-PCC012V1) and EVALST7570-1 . . . . . . . . . . . . . . . . . 16

A.2 STM32 (STEVAL-PCC012V1) and EVALST7590-1 . . . . . . . . . . . . . . . . . 17

A.3 STM32 (STM3210C-EVAL) and EVALST7590-1 . . . . . . . . . . . . . . . . . . . 17

A.4 SPEAr320 and EVALST7590-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

A.5 SPEAr310 and EVALST7590-1 via RS232 . . . . . . . . . . . . . . . . . . . . . . . . 18

A.6 Any SPEAr3xx and ST7570, ST7580 or ST7590 via USB . . . . . . . . . . . . 19

A.7 EVALSPEAr320HMI and ST7570, ST7580, ST7590 via UART . . . . . . . . 20

Appendix B Additional schematics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

B.1 STEVAL-PCC001V1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

B.2 Extension connectors at SPEAr320HMI board . . . . . . . . . . . . . . . . . . . . . 22

Appendix C Endnotes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

UM1038 List of tables

Doc ID 18303 Rev 1 3/24

List of tables

Table 1. Interconnection of demonstration boards EVALST7570 and STEVAL-PCC012V1 . . . . . . . 6

Table 2. Interconnection of demonstration boards EVALST7590 and STEVAL-PCC012V1 . . . . . . . 8

Table 3. Interconnection of STM3210C-EVAL and EVALST7590-1. . . . . . . . . . . . . . . . . . . . . . . . . . 9

Table 4. STM3210C-EVAL jumper position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Table 5. Interconnection of EVALSPEAr320 and EVALST7590-1 . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Table 6. EVALSPEAr320HMI, unified PLM connector CN704 (ST7570/80/90) . . . . . . . . . . . . . . . . 15

Table 7. Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

List of figures UM1038

4/24 Doc ID 18303 Rev 1

List of figures

Figure 1. EVALST7570 - microcontroller extension connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Figure 2. STEVAL-PCC012V1 - PLM connector CN7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Figure 3. STEVAL-PCC012V1 - board settings by JP2 and JP3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Figure 4. Connectors interconnection - 14-pin STM32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Figure 5. Connectors interconnection - 20-pin ST7570 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Figure 6. EVALST7590 - microcontroller extension connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Figure 7. EVALST7590 - jumper setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Figure 8. STEVAL-PCC012V1 - PLM connector CN7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Figure 9. Connectors interconnection - 14-pin STM32 and 14-pin ST7590. . . . . . . . . . . . . . . . . . . . . 8

Figure 10. SPEAr320 and EVALST7590-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Figure 11. EVALSPEAr310 and EVALST7590-1 via RS232 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Figure 12. STEVAL-PCC001V1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Figure 13. EVALSPEAr3xx and ST7570, ST7580, ST7590 via USB . . . . . . . . . . . . . . . . . . . . . . . . . 13

Figure 14. EVALSPEAr320HMI and ST7570, ST7580, ST7590 via UART . . . . . . . . . . . . . . . . . . . . . 14

Figure 15. EVALSPEAr320HMI, unified PLM connector CN704 (ST7570/80/90) . . . . . . . . . . . . . . . . 14

Figure 16. ST7570 and STEVAL-PCC012V1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Figure 17. ST7590 and STEVAL-PCC012V1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Figure 18. ST7590 and STM3210C-EVAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Figure 19. SPEAr320 and EVALST7590-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Figure 20. SPEAr310 and EVALST7590-1 via RS232 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Figure 21. Any SPEAr3xx and ST7570, ST7580 or ST7590 via USB . . . . . . . . . . . . . . . . . . . . . . . . . 19

Figure 22. SPEAr320HMI and ST7570 via the unified connector, UART . . . . . . . . . . . . . . . . . . . . . . 20

Figure 23. STEVAL-PCC001V1 schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Figure 24. SPEAr320HMI, CN701 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Figure 25. SPEAr320HMI, CN702 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

UM1038 STM32 (STEVAL-PCC012V1) and EVALST7570-1

Doc ID 18303 Rev 1 5/24

2 STM32 (STEVAL-PCC012V1) and EVALST7570-1

The demonstration boards necessary to connect the STM32 and ST7590 boards and their

configuration:

1. STEVAL-PCC012V1

●Flash the correct firmware into STM32.

●Configure the board according to Figure 3.

2. EVALST7590-1

●Put the jumper into position JP12 - USB_RES (see paragraph 1

in Appendix C).

●Interconnect EVALST7570-1 according to Table 1, Figure 4 and Figure 5.

Figure 1. EVALST7570 - microcontroller extension connection

Figure 2. STEVAL-PCC012V1 - PLM connector CN7

33.

3#,+

-/3)?3$!

-)3/

3#,+?3#,

-/3)?48$

6$$)/

'0)/?0

'0)/?0

'0)/?0

'0)/

6##

6$$)/

'0)/?0

'0)/?0

2%3%4.

2%3%4.?34

6$$)/

-)3/?28$ -/3)?48$

-)3/?28$

4?2%1

2 22









































*

#/.!0



*0

#,/3%

!-

 

 

 

 

 

 

 

#.

(EADER X 

-)3/

-/3) 3#+

-$-?2%3

6

DFU

RTS CTS

33.

53!24?48

53!24?28

4X$ 2X$

!-

STM32 (STEVAL-PCC012V1) and EVALST7570-1 UM1038

6/24 Doc ID 18303 Rev 1

Figure 3. STEVAL-PCC012V1 - board settings by JP2 and JP3

Figure 4. Connectors interconnection - 14-pin STM32

Figure 5. Connectors interconnection - 20-pin ST7570

Table 1. Interconnection of demonstration boards EVALST7570 and STEVAL-

PCC012V1

Signal J5 (ST7570) CN7 (STM32) Color notation

TxD --> RX 16 (TxD) 1 (RX) Blue

RxD <-- TX 18 (RxD) 2 (TX) Green

T_REQ 15 (GPIO3) 11 (MDM_RES) Purple

+3.3 V Not connected 4 Red

GND 2 13, 14 Black







*0







*0

3$!

3$!?-%-3

53!24?28

3#,

3#,?-%-3

53!24?48

!-









 

 

 

!-









 

 

 

 

 

 

!-

UM1038 STM32 (STEVAL-PCC012V1) and EVALST7590-1

Doc ID 18303 Rev 1 7/24

3 STM32 (STEVAL-PCC012V1) and EVALST7590-1

The demonstration boards necessary to connect the STM32 and ST7590 boards and their

configuration:

1. STEVAL-PCC012V1

●Flash the correct firmware into STM32.

●Configure the board according to Figure 3.

2. EVALST7590-1

●Put the jumper into position JP12 - USB_RES (see paragraph 1

in Appendix C).

●Configure the board according to Figure 7.

●Interconnect EVALST7590-1 according to Table 2 and Figure 9.

Figure 6. EVALST7590 - microcontroller extension connector

Figure 7. EVALST7590 - jumper setup

Figure 8. STEVAL-PCC012V1 - PLM connector CN7

3#,+?,6

33.?,6

5!24?28$?,6

#43?,6243?,6

-/3)?,6

-)3/?,6

5!24?48$?,6

$&5?&/2#%?,6-$-?2%3N?,6

6##?,6























 

 

 

*

#/.!

!-

5!24?28$

5!24?48$

'0)/

5!24?28$

5!24?48$

'0)/

 

*0 5!24

 

*0 #,/3%#,/3%

 

30)

*0

#,/3%

6##

!-

 

 

 

 

 

 

 

#.

(EADER X 

-)3/

-/3) 3#+

-$-?2%3

6

DFU

RTS CTS

33.

53!24?48

53!24?28

4X$ 2X$

!-

STM32 (STEVAL-PCC012V1) and EVALST7590-1 UM1038

8/24 Doc ID 18303 Rev 1

Figure 9. Connectors interconnection - 14-pin STM32 and 14-pin ST7590(1)

1. See paragraph 2in Appendix C.

Table 2. Interconnection of demonstration boards EVALST7590 and STEVAL-

PCC012V1

Signal J8 (ST7590) CN7 (STM32)

TxD --> RX 1 (TxD_LV) 1 (RX)

RxD <-- TX 2 (RxD_LV) 2 (TX)

MDM_RES 11 (MDM_RESn_LV) 11 (MDM_RES)

MOSI_LV 7 (JP8 disconnected) 7 (MOSI) no collision if JP8 disconnected

MISO_LV 5 5 (MISO)(1)

1. Possible collision with SD Card™ (if inserted), Wi-Fi (if assembled), MEMS analog (if SPI signal used by

R63, R64 with zero value), MEMS digital (if plugged).

SSN0 6 6 (SSN0) no collision

SCK 88(SCK)

(1)

+3.3 V 4 (VCC_LV) 4 (+3.3 V)

GND 13, 14 13, 14









 

 

 

!-



UM1038 STM32 (STM3210C-EVAL) + EVALST7590-1

Doc ID 18303 Rev 1 9/24

4 STM32 (STM3210C-EVAL) + EVALST7590-1

The demonstration boards necessary to connect the STM3210C-EVAL and EVALST7590

boards and their configuration:

1. STM3210C-EVAL

●Configure the board: jumper positions according to Table 4 .

●Flash the correct firmware into STM32.

2. EVALST7590-1

●Put the jumper into position JP12 - USB_RES (see paragraph 1

in Appendix C).

●Interconnect EVALST7590-1 according to Table 3 and Figure 9.

Table 3. Interconnection of STM3210C-EVAL and EVALST7590-1

Signals - STM3210C-EVAL Cable color ST7590 connector

+3.3 V (CN8 - pin 48) Red +5 V (or +3.3 V) (pin 4)

GND (CN8 - pin 50) Black GND (pin 14)

STM32 UART TX (CN9 - pin 12 - PD8) Green ST7590 RX (pin 2)

STM32 UART RX (CN9 - pin 8 - PD9) Blue ST7590 TX (pin 1)

Table 4. STM3210C-EVAL jumper position

Signals - STM3210C-EVAL ST7590 connector

JP25 USB - open, DTB - open, PSU - closed

JP26 Closed

JP15 SD position closed

JP13 No jumper

JP11 No jumper

JP12 No jumper

JP1 Anti_TMP position closed

JP24 No jumper

JP9 Closed

JP17 Closed

JP20 Open

SPEAr320 and EVALST7590-1 UM1038

10/24 Doc ID 18303 Rev 1

5 SPEAr320 and EVALST7590-1

Figure 10. SPEAr320 and EVALST7590-1

The demonstration boards necessary to connect the EVALSPEAr320 and EVALST7590

boards and their configuration:

1. EVALSPEAr320

●Interconnect PC with UART1.

●Interconnect Ethernet to network.

●Plug Flash disk with correct SW into the first USB, use the file system of this

USB.

2. EVALST7590-1

●Put the jumper into position JP12 - USB_RES (see paragraph 1

in Appendix C).

●Interconnect EVALST7590-1 and EVALSPEAr320 according to Table 5 , Figure 9

and Figure 10.

Table 5. Interconnection of EVALSPEAr320 and EVALST7590-1

Signals - EVALSPEAr320 - UART0 Cable color ST7590 connector

+5 V (or +3.3 V) (J3 - pin 2) Red +5 V (or +3.3 V) (pin 4)

GND (J3 - pin 4) Black GND (pin 14)

SPEAr UART0 TX (J20 - pin 2) Green ST7590 RX (pin 2)

SPEAr UART0 RX (J21 - pin 2) Blue ST7590 TX (pin 1)

30%!R



BOARD

0,-

34

66

5!24

6

!-

Altri manuali per STM32 Nucleo

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali ST Microcontrollore

ST Sound Terminal STA333W Manuale utente

ST STM32 Nucleo Manuale utente

ST STM32F413 Series Manuale utente

ST STM32L0x3 Manuale utente

ST STM32F2 Series Manuale utente

ST STM32F103ZE Manuale utente

ST STM32F10 Series Istruzioni per l'installazione e il funzionamento

ST P-NUCLEO-LRWAN2 Manuale utente

ST UM0250 Manuale utente

ST UM2708 Manuale utente

ST EVLKST8500GH868 Manuale utente

ST STEVAL-MKBOXPRO Manuale utente

ST STM32F101xx series Manuale utente

ST STM32F0 Series Manuale del proprietario

ST STEVAL-L6982NDR Manuale utente

ST SPC582B Series Istruzioni per l'installazione e il funzionamento

ST STM32H745I-DISCO Manuale utente

ST SPC560P34 Manuale utente

ST STM32F205 series Manuale del proprietario

ST STEVAL-FKI433V1 Manuale utente

ST STR71xF Manuale utente

ST STM32L496 Series Istruzioni per l'installazione e il funzionamento

ST STEVAL-STWINBX1 Manuale utente

ST STM32L0 Series Istruzioni per l'installazione e il funzionamento

Manuali Microcontrollore popolari di altre marche

AMS

AMS AS7261 Demo Kit Manuale utente

Novatek

Novatek NT6861 Manuale utente

Espressif Systems

Espressif Systems ESP8266 SDK Guida all'installazione

Nuvoton

Nuvoton ISD61S00 ChipCorder Guida

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manuale utente

Texas Instruments

Texas Instruments Chipcon CC2420DK Manuale utente

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manuale utente

NEC

NEC 78GK0S/K 1+ Series Istruzioni per l'installazione e il funzionamento

Mikroe

Mikroe SEMITECH N-PLC Click Istruzioni per l'installazione e il funzionamento

Intel

Intel Agilex Manuale utente

Cypress

Cypress CY4607 HX2VL Manuale utente

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manuale utente

Texas Instruments

Texas Instruments TMS320F2837 D Series Manuale utente

CYPRES

CYPRES CY14NVSRAMKIT-001 Manuale utente

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Manuale utente

Espressif Systems

Espressif Systems ESP8266EX Istruzioni operative

Abov

Abov AC33M8128L Manuale utente

Laird

Laird BL654PA Manuale utente