Stack-On QAS-1510-B Manuale utente

40707-1608 114

Serial #:

IMPORTANT

CONTROL FEATURES

Record the serial number from the tag on the door front.

Keep keys in a secure place away from children.

1. Key lock

2. Fingerprint scanner

3. Reset button (inside safe)

4. Battery Compartment (inside safe)

5. Indicator light

Instructions

QAS-1510-B

NOTE: You can store your Key # and your

Serial # information on Stack-On’s SECURE

web site – stack-on.com under

Customer

Service

. Storing your Key # will provide instant

access to this important information, should you

ever lose your keys or need the number to

order a new set.

Only you will have access to this information.

DO NOT STORE YOUR KEYS INSIDE THE SAFE.

Tools Required:

Drill

Flat Head Screwdriver

10 mm Wrench

3/16” (5 mm) drill bit for drilling into wood

Hardware Included:

(4) M6 x 20 mm (3/4” long) Screws

(4) Washers

(4) Plastic anchors

GETTING STARTED REMOVING THE DRAWER

REMOVING THE DRAWER

Remove the foam drawer liner. Pull the drawer all the

way open. Locate the access hole. Using a small

screwdriver or pointed tool, move the clear tab to the

right and pull the drawer o the slide as shown.

NOTE: You can also access the tab by reaching

under the drawer and moving the tab with your

nger. If the safe has been mounted to a permanent

shelf, you will have to remove the drawer as

described above.

When you rst receive your safe you will need to

open the drawer with the key and remove the

drawer in order to install the baeries. Baeries

are included and are located inside the drawer.

NOTE: is key has also been provided if the

baeries run low. If you lose your key, you may

purchase a replacement key by referencing the serial

number located on the front of the drawer. See

section regarding replacement keys for further

information.

To open the safe, insert key into lock and turn

clockwise until the drawer automatically opens.

NOTE: You must turn the key back to the

locked position before you are able to close and

lock the drawer.

40707-1608 214

40707-1608 314

INSTALLING THE BATTERIES

NOTE: Do not mix old and new baeries. Do not

mix alkaline, standard or rechargeable baeries.

NOTE: If the baeries are low the indicator light will

ash blue when you start scanning. Replace with 4

new AA alkaline baeries as shown.

RECORDING FINGERPRINTS

To record a ngerprint, rst press the Reset Buon on

the inside of the safe. e scanner will turn blue with

two beeps (if the sound is turned on)and the blue

light ashes twice, you will then record the same

nger three times as follows:

1. Place your nger on the scanner until there

is one beep (if the sound is turned on) and the

green light ashes once. Li your nger o

the scanner.

2. Place the same nger on the scanner for a

second time, holding the nger in the same

position until there is one beep (if the sound is

turned on) and the green light ashes once.

Li your nger o the scanner.

3. Place the same nger on the scanner for a

third time, holding the nger in the same

position until there are two beeps (if the sound is

turned on) and the green light ashes twice.

Li your nger o the scanner. Your ngerprint

is now recorded.

NOTE: In certain dry climate conditions, your

ngerprint may not scan. If your ngerprint did not

scan, we recommend moisturizing with minimal

lotion and trying again.

SCAN THE SAME FINGER 3X

If the red light ashes three times with three beeps

(if the sound is turned on) your ngerprint did not

get recorded and you will have to start over.

If you try entering more than 20 ngerprints, the red

light will ash 5 times and there will be 5 beeps

(if the sound is turned on).

When you rst receive your safe there are no recorded

ngerprints. Any ngerprint will open the safe

until a ngerprint is recorded. For security you

must record a ngerprint. Failure to do so will

compromise the safety and security of the safe. You

can record up to 20 dierent ngerprints for opening

the safe. For best results, each individual should

use their thumb or index nger only.

Aer removing the drawer, push the baery cover

locking tab with a screwdriver to release the cover.

Install the (4) AA alkaline baeries as shown.

Replace the cover by inserting the rear tabs in the

slots and snapping the cover in place.

40707-1608 414

TURNING THE SOUND OFF/ON

CLEARING THE MEMORY

To turn the sound o, press the scanner with a

recorded ngerprint for 10 seconds until the green

light ashes twice.

To turn the sound on, press the scanner with a

recorded ngerprint until you hear two beeps and

the green light ashes twice.

Your safe comes with the beep sound turned on.

To clear the memory of all recorded ngerprints,

locate the reset buon on the inside of the safe

and press this buon for about 5 seconds until

the green light ashes 10 times. All recorded

scans will be erased.

NOTE: For security you must record a

ngerprint. Failure to do so will compromise

the safety and security of the safe.

OPENING THE SAFE USING YOUR

FINGERPRINT

To open the safe, press the scanner with a recorded

nger. e blue light will come on with one beep (if

the sound is turned on) and the scan will begin.

If the green light fashes twice with 2 beeps (if the

sound is turned on), the scan has been accepted

and the drawer will open.

If the red light ashes once, the scanner did not read

your ngerprint and you must try again. If the red

light ashes 3 times, the scanner read your ngerprint

and did not accept it.

If there are 3 rejected scans, where your

ngerprint was read, and the red light ashes 5

times with 5 beeps (if the sound is turned on),

you will have an automatic lockout for 60

seconds before you can try a scan again. e

safe will beep one time (if the sound is turned

on) and the green light will ash once when the

lockout period is over.

If there is 1 more rejected scan where your

ngerprint was read and the red light ashes 5 times

with 5 beeps (if the sound is turned on), you will

have an automatic lockout for 5 minutes before you

can try a scan again. e safe will beep one time (if

the sound is turned on) and the green light will ash

once when the lockout period is over.

STACK-ON PRODUCTS CO.

P.O. BOX 489, WAUCONDA, IL 60084

NOTE: is safe is designed to be mounted to a

shelf. Aaching the safe with a cable to a xed

object, as the sole means of securing the safe, will

compromise the safety and security of the safe.

SELECTING A LOCATION

IMPORTANT

Keep keys in a secure place, away from children. Keep this

record of your serial number in a secure place separate

from your safe. To order a replacement key set, follow the

instructions on the aached form.

To secure the case to a xed object, loop the cable

around the object and place the cable’s small end into

the key hole on the side of the safe while the drawer

is open. Locking the drawer will secure the cable end

in the safe.

SECURING THE SAFE WITH THE CABLE

SECURING THE SAFE WITH HARDWARE

Using the template, mark the holes to be used.

Drill 3/16” diameter pilot holes.

Install the rear screws so there is just enough room

between the head of the screw and the mounting

surface for the key slots. (Figure 2)

Slide the unit into place and secure the front

mounting holes with the screws and washers.

(Figure 3)

40707-1608 514

Figure 1

Figure 2

e safe must be mounted to a shelf.

For optimal

safety and security, the safe should be installed in

an isolated, dry and secure area.

Figure 3

THE SAFE SHOULD ALWAYS BE KEPT

OUT OF THE REACH OF CHILDREN.

REINSTALLING THE DRAWER

To reinstall the drawer, align the drawer slide and push

the drawer in until it locks in place.

NOTE ON LOCKING THE SAFE: e safe

needs to be in an upright position, as shown in

gure 1, for the locking mechanism to function

properly. Failure to mount the safe in the

corrrect upright position will compromise the

safety and security of the safe

NOTE: is safe must be mounted to a shelf.

Failure to do so will compromise the safety and

security of the safe.

Do not use glass cleaners or sprays on this safe.

Clean with a damp cloth.

MAINTENANCE

Key Request

“This is not a Registration Form”

Verification of ownership is required in order to receive replacement key for your security product.

In order to receive a replacement key to your security product:

1. Complete the following form and send to Stack-On Products.

2. Send a copy of your valid driver’s license along with the form.

3. Send a copy of the receipt showing the original purchase.

4. Security product owner must sign form.

5. Owner’s signature must be notarized.

6. Send $10.00 for replacement key. Personal Check, MasterCard, or Visa accepted.

7. Send completed information to:

Stack-On Products Company

1360 N. Old Rand Road

P.O. box 489

Wauconda, IL 60084

Serial Number______________________ Key Number (if applicable) _______

Unit Dimensions________________________________________

Unit Description___________________________________________________________

Owner’s Name ____________________________________ Date Purchased___/___/____

Owner’s Address ___________________________ Unit or Apt Number _________________

City ___________________________ State _______________ Zip Code________________

Telephone Number: (____)___________________ Fax Number: (____)___________________

Owner’s Email Address: ________________________________________________________

Owner’s Signature __________________________ Notary Signature________________

Notary Commission Expires: _____/_____/_____ Notary Stamp

SERVICE REQUESTED

Key Replacement: Yes No

$10.00 charge for this service

Credit Card Information (Please circle one) MasterCard Visa

Expiration Date: ___/___/___ Card Number:______________________________________

Credit Card Identification Number (Located on back of card, last 3 digits on signature strip)_________

9/07

NOTE: You can store your Key # and your Serial # information on Stack-On’s SECURE web site – stack-on.com under Customer

Service. Storing your Key # will provide instant access to this important information, should you ever lose your keys or need the

number to order a new set.

Only you will have access to this information.

40707-1608 614

40707-1608 714

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS

WHICH VARY FROM STATE TO STATE.

IN NO EVENT SHALL STACK-ON’S OBLIGATION UNDER THIS WARRANTY EXCEED THE PRICE

OF THE PRODUCT.

STACK-ON’S LIABILITY FOR ANY BREACH OF THIS WARRANTY SHALL BE LIMITED

EXCLUSIVELY TO REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT, AS DESCRIBED

ABOVE, OR A REFUND OF THE PURCHASE PRICE OF THE PRODUCT.

STACK-ON WILL NOT, UNDER ANY CIRCUMSTANCES, BE LIABLE TO THE INITIAL CONSUMER

FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL, EXEMPLARY, OR PUNITIVE DAMAGES

ARISING OUT OF THE PURCHASE OR USE OF ANY STACK-ON PRODUCTS, INCLUDING THE

SAFES.

THIS WARRANTY IS EXCLUSIVE AND EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES

EXPRESSED OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE, WHICH ARE HEREBY DISCLAIMED AND EXCLUDED. STACK-ON

SHALL NOT BE SUBJECT TO ANY OTHER OBLIGATIONS OR LIABILITIES. STACK-ON NEITHER

ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT, ANY OTHER LIABILITY

IN CONNECTION WITH THE SALE OF STACK-ON’S STEEL SAFES.

THIS WARRANTY DOES NOT COVER ANY PRODUCT, OR ANY PART OF ANY PRODUCT, WHICH

HAS BEEN SUBJECT TO EXCESSIVE USE, ACCIDENT, NEGLIGENCE, ABUSE OR MISUSE,

INCORRECT MAINTENANCE, ALTERATION OR REPAIR BY ANYONE OTHER THAN STACK-ON. IN

ADDITION, THIS WARRANTY DOES NOT COVER ANY ACCESSORIES OR PARTS USED WITH OR

IN THE PRODUCT WHICH ARE NOT INCLUDED WITH THE ORIGINAL PURCHASE.

If Stack-On is properly notified during the three-year warranty period and, after inspection confirms there

is a defect, Stack-On will, at its sole option, provide repair parts or exchange the product at no charge, or

refund the purchase price of the product.

Stack-On Products Company

1360 North Old Rand Road

Wauconda, IL 60084

[email protected]

If you believe there is a defect in material or workmanship in your Steel Safe during the three-year

warranty period, please contact our customer service department, by regular mail or email at the address

listed below, and include with your correspondence proof of purchase information and the model number

of the safe.

Stack-On Products Co. (“Stack-On”) Steel Safes are warranted to be free from defects in material and

workmanship for a period of three (3) years from the date of original purchase by a consumer. This

warranty extends to the initial consumer only.

LIMITED THREE YEAR WARRANTY

STEEL SAFES

40707-1608 814

Instrucciones

IMPORTANTE

# Serie:

CARACTERISTICAS DE CONTROL

Registre el número de serie que aparece en la

etiqueta en frente de la puerta.

Mantenga las llaves en un lugar seguro lejos de los

niños(a).

NO GUARDE SUS LLAVES ADENTRO EN

LA CAJA FUERTE.

Para abrir la caja fuerte, llave insertar en la cerradura

y gire hacia la derecha hasta que la puerta se abre

automáticamente. NOTA: Usted debe girar la llave a

la posición de bloqueo antes de poder cerrar y

bloquear la puerta.

Cuando usted primero reciba su caja fuerte usted

tendra que abrir la puerta con las llaves para

instalar las baterías/pilas. Las baterías/pilas

vienen incluidas y están situadas adentro de la su

caja fuerte.

PARA COMENZAR

NOTA: Esta llave se ha proporcionado encaso de

que las baterías esten bajas. Si usted pierde su llave,

usted puede comprar una llave de reemplazo

reriéndose al número de serie situado en el frente

de la puerta. Consulte la sección relativa a las llaves

de repuesto para más información.

1. Cerradura con Llave

5. La luz indicadora

2. Grabadora de Huellas digitales

3. Botón de reajuste

(adentro de la caja fuerte)

4. Compartimiento para las baterías/pilas

(adentro de la caja fuerte)

NOTA: Usted puede almacenar su Numero de Llave y

su Numero de Serie e información en el Web-Site de

Stack-On: stack-on.com bajo la opcion de Servicio.

Almacenando su Numero de Llave en el web-site le

proporcionará acceso de inmediato a su información

importante, en caso de que usted pierda sus llaves o

necesita ha pedir otro juego de llaves. Asi solamente

usted tendra acceso a esta información.

QAS-1510-B

Herramientas necesarias:

perforar

Destornillador de cabeza plana

10 mm Llave

Taladro 3/16 "(5 mm) de bits para perforar madera

Hardware incluido:

(4) M6 x 20 mm (3/4 "de largo) Tornillos

(4) Arandelas

(4) anclajes de plástico

PARA COMENZAR ELIMINANDO EL CAJÓN

ELIMINANDO EL CAJÓN

Quite el trazo de espuma alineando elcajón. Estire el

cajón hasta que esteabierto completamente

Localice el agujero de acceso. Usando un

destornillador pequeño o una herramienta

acentuada, mueva la lengüeta clara hacia la derecha y

estire el cajón de la diapositiva como se muestra.

Cuando usted primero reciba su caja/cajon fuerte

usted necesitará que abrir el cajón con la llave y

quitar el cajón para instalar las baterías/pilas. Las

baterías/pilas son incluidas y están situadas

adentro del cajón.

NOTA: Esta llave se le ha proporcionado en caso de

que usted pierda o olvide que su código de seguridad

o si las baterías/pilas estan bajas. Si usted pierde su

llave, usted puede comprar una llave de reemplazo

reriéndose al número de serie situado en el frente de

la puerta. Vease las instruciones hacia el nal de estas

ojas con respecto a llaves de reemplazo.

Para abrir la caja/cajón fuerte, inserte la llave en la

cerradura y de vuelta hacia la derecha hasta que el

cajón se abra automáticamente. NOTA: Usted debe

dar vuelta de nuevo a la llave a la posición original

antes de que usted pueda cerrar y trabar el cajon.

NOTA: Si la caja fuerte no esta montada, usted

puede tener acceso a la lengüeta alcanzando por

debajo del cajón y moviendo la lengüeta con su dedo.

Si la caja fuerte esta montada en una localización

donde el cajón se abre sobre una supercie sólida,

usted tendrá que quitar el cajón como se describe

anteriormente.

40707-1608 914

40707-1608 1014

INSTALACIÓN DE LAS PILAS

NOTA: Si las baterías están bajas la luz indicadora

parpadee en azul cuando se inicia el escaneado.

Reemplazar con 4 pilas alcalinas AA como se

muestra.

NOTA: No mezcle pilas viejas y nuevas. No mezcle

pilas alcalinas, pilas estándar o recargables.

Si su seguro incluye un estante, quitarlo para un

mejor acceso al compartimiento de la batería/pilas.

Empuje la cubierta e traba de las baterías/pilas con

un destornillador para lanzar la cubierta. Instale las

(4) baterias/pilas de alcalino AA como se muestra.

Regrese la cubierta insertando las lengüetas

posteriores en las ranuras y precionando la cubierta

levemente en su lugar.Instalación de las

Baterías/Pilas.

GRABACIÓN DE HUELLAS DIGITALES

Para registrar una huella digital, primero pulse el

botón de reinicio en el interior de la caja fuerte. El

escáner se vuelve azul con dos pitidos ( si el sonido

está activado) y el verde luz parpadea dos veces, a

continuación, se registrará la misma dedo tres veces

como sigue:

1. Coloque el dedo en el escáner hasta que haya un

pitido (si el sonido está activado) y la luz verde

parpadea una vez . Levantar el dedo del escáner.

2. Coloque el mismo dedo en el escáner por

segunda vez, sostiene el dedo en la misma posición

hasta que haya un pitido (si el sonido está activado)

y la luz verde parpadea una vez. Levantar el dedo del

escáner.

3. Coloque el mismo dedo en el escáner por tercera

vez, sostiene el dedo en la misma posición hasta que

haya dos pitidos (si el sonido está activado) y la luz

verde parpadea dos veces. Levantar el dedo del

escáner. Su huella digital se registra ahora.

NOTA: En ciertas condiciones de clima seco, su

huella digital no puede escanear. Si su huella digital

no se ha escaneado, se recomienda hidratación con

loción de mínima y de volver a intentarlo.

ESCANEAR EL MISMO DEDO 3X

Si la luz roja parpadea tres veces con tres pitidos (si el

sonido está activado) su huella digital no consiguió

registrada y usted tendrá que empezar de nuevo.

Si introduce más de 20 huellas dactilares, la luz roja

parpadeará 5 veces y habrá 5 pitidos (si el sonido está

activado).

Cuando usted recibe por primera ocasión su caja fuerte,

esta no tendrá registrada ninguna huella digital.

Cualquier huella digital abrirá la caja fuerte hasta que

usted registre su propia huella digital. Por razones de

seguridad usted deberá registrar su huella digital. Si usted

no registra su huella digital esto comprometerá la

seguridad de su caja fuerte. Usted podrá registrar hasta

20 diferentes huellas digitales para abrir su caja fuerte.

Para mejor resultados, cada persona deberá usar

solamente el dedo índice o pulgar.

Indice

Lingue:

Altri manuali Stack-On Sicuro

Stack-On

Stack-On SECURITY PLUS GC-908-5 Manuale utente

Stack-On

Stack-On QAS-1000 Manuale utente

Stack-On

Stack-On W-22-BH-E-S Manuale utente

Stack-On

Stack-On QAS-1845-E Manuale utente

Stack-On

Stack-On QAS-450-B Manuale utente

Stack-On

Stack-On PFWS-080-B-D-E Manuale utente

Stack-On

Stack-On PS-5-B-12 Manuale utente

Stack-On

Stack-On PDS-1500-B Manuale utente

Stack-On

Stack-On QAS-1304-12 Manuale utente

Stack-On

Stack-On PS-15-20-B Manuale utente

Stack-On

Stack-On A-64-MB-E-S-72 Manuale utente

Stack-On

Stack-On TD-040-GP-E Manuale utente

Stack-On

Stack-On PWS-15522-B Manuale utente

Stack-On

Stack-On Sentinel GCWB-18 Manuale utente

Stack-On

Stack-On SECURITY PLUS Manuale utente

Stack-On

Stack-On E-48-MG-C-S Manuale utente

Stack-On

Stack-On E-30-MB-E-S Manuale utente

Stack-On

Stack-On GCG-8RTA Manuale utente

Stack-On

Stack-On PDS-1500 Manuale utente

Stack-On

Stack-On QAS-450 Manuale utente

Stack-On

Stack-On SECURITY PLUS Manuale utente

Stack-On

Stack-On SHD-AOTT-BG-B Manuale utente

Stack-On

Stack-On PC-95K-RTX Manuale utente

Stack-On

Stack-On Security Plus QAS-710 Manuale utente

Manuali Sicuro popolari di altre marche

Squire

Squire Stronghold Keysafe Manuale utente

Phoenix

Phoenix FS0352C Scheda informativa del prodotto

Phoenix

Phoenix KS0030E Series Manuale utente

Vaultek

Vaultek 10 Series Scheda tecnica

Arregui

Arregui CLASS Manuale utente

Beaumont

Beaumont SMART KEYBOX Manuale utente

Honeywell

Honeywell 2077D - 1.21 Cubic Foot Anti-Theft Safe Manuale utente

Hornady

Hornady SnapSafe Trunk Safe II Manuale utente

SPORTS AFIELD

SPORTS AFIELD SA-HD5-BIO Manuale utente

Honeywell

Honeywell 5912 Manuale utente

Phoenix

Phoenix FS1280F Manuale utente

Phoenix

Phoenix SS0992K Scheda informativa del prodotto

Technomax

Technomax Trony Series Manuale

SPORTS AFIELD

SPORTS AFIELD INSTINCT BIOMETRIC Series Manuale utente

RICHTER CZECH

RICHTER CZECH LA Manuale operativo

Olymp

Olymp GOsafe 110 Manuale utente

Phoenix

Phoenix SS0100E Scheda informativa del prodotto

Clarke

Clarke Strong-Arm CS1000K Manuale di istruzioni