Stack-On QAS-1510 Manuale utente

40706-1608 114

Your Electronic Safe Combination:

Serial #:

Instructions

QAS-1510

IMPORTANT

NOTE: You can store your Key #, Serial # and

Combination on Stack-On’s SECURE web site

– stack-on.com under Customer Service.

Storing your Key # or Combination will provide

instant access to this important information

should you ever lose your keys or your

combination.

Only you will have access to this information.

CONTROL FEATURES

1. Key lock

2. Combination buttons

3. Reset button (inside safe)

4. Battery Compartment (inside safe)

Record the serial number from the tag on the door front.

Record your combination.

Keep keys and combination in a secure place away

from children.

DO NOT STORE YOUR KEYS OR COMBINATION

INSIDE THE SAFE.

Tools Required:

Drill

Flat Head Screwdriver

10 mm Wrench

3/16” (5 mm) drill bit for drilling into wood

Hardware Included:

(4) M6 x 20 mm (3/4” long) Screws

(4) Washers

(4) Plastic anchors

GETTING STARTED REMOVING THE DRAWER

REMOVING THE DRAWER

Remove the foam drawer liner. Pull the drawer all the

way open. Locate the access hole. Using a small

screwdriver or pointed tool, move the clear tab to the

right and pull the drawer o the slide as shown.

When you rst receive your safe you will need to

open the drawer with the key and remove the

drawer in order to install the baeries. Baeries

are included and are located inside the drawer.

NOTE: is key has also been provided if you lose

or forget your security code or the baeries run low.

If you lose your key, you may purchase a replacement

key by referencing the serial number located on the

front of the drawer. See section regarding

replacement keys for further information.

To open the safe, insert key into lock and turn

clockwise until the drawer automatically opens.

NOTE: You must turn the key back to the

locked position before you are able to close and

lock the drawer.

40706-1608 214

NOTE: You can also access the tab by reaching

under the drawer and moving the tab with your

nger. If the safe has been mounted to a permanent

shelf, you will have to remove the drawer as

described above.

40706-1608 314

INSTALLING THE BATTERIES

NOTE: Do not mix old and new baeries. Do not

mix alkaline, standard or rechargeable baeries.

Aer removing the drawer, push the baery cover

locking tab with a screwdriver to release the cover.

Install the (4) AA alkaline baeries as shown.

Replace the cover by inserting the rear tabs in the

slots and snapping the cover in place.

NOTE: If the baeries are low the combination

buons will ash red when pushed. Replace with

4 new AA alkaline baeries as shown.

• For security you must program your own

combination aer opening the safe.

• Record your new combination on this form

or store your combination on our secure

website at stack-on.com under Customer

Service. If you write down your combination

you must keep this information in a secure

place, away from children, not inside the safe.

PROGRAMMING YOUR OWN

ELECTRONIC COMBINATION

Press the Reset Buon (3) located inside the safe.

Two “beeps” will sound (if the sound is turned

on) and all 3 buons will ash blue twice. You

will have 5 seconds to begin entering your

combination or you will have to start over.

Example: (RIGHT) - (LEFT) - (CENTER) -

(LEFT) - (RIGHT)

For each combination entry a “beep” will sound

(if the sound is turned on) and all the buons

will light up green. If you delay more than 5

seconds between entries you will have to start

over from step 1. Aer you have nished

entering your combination, you will have 5

seconds to press the Reset Buon to record

your new combination or you will have to start

over from step 1.

Enter your own 3-8 buon combination by

pressing any combination of the 3 buons.

3. When you press the Reset Buon to record

your new combination, there will be two

“beeps” (if the sound is turned on) and all 3

keys ash blue twice, indicating your new

combination has been recorded.

Reset Button

40706-1608 414

OPENING THE SAFE USING

YOUR COMBINATION

Enter your combination using the buons. e

buons will light up green and there will be one

“beep” for every entry (if the sound is turned on). If

you entered the correct combination, the buons will

ash green and the drawer will open. If the

combination is incorrect the safe will beep 3 times (if

the sound is turned on) and the red light will ash 3

times. NOTE: You will have 2 seconds between

individual entries before the safe assumes you have

entered your complete combination.

To close the safe, push the drawer closed until locked.

TURNING THE KEYPAD SOUND

OFF/ON

You can turn o the "Beep" sound of the keypad by

pressing all the buons at the same time and

holding for 3 seconds until the green light ashes.

To turn the "Beep" sound on, press the le and

middle buon at the same time and hold for 3

seconds until the green light ashes.

If an incorrect security code is entered 3 times the

safe will beep 5 times (if the sound is turned on)

and the red light will ash 5 times resulting in the

safe being automatically locked out for 60 seconds

before you can try your code again. e safe will

beep one time (if the sound is turned on) and the

green light will ash once when the lockout

period is over.

If an incorrect security code is entered 1

additional time the safe will beep 5 times

(if the sound is turned on) and the red light will

ash 5 times resulting in the safe being

automatically locked out for 5 minutes before the

code can be tried again. e safe will beep one

time (if the sound is turned on) and the green

light will ash once when the lockout

period is over.

Your safe comes with the "Beep" sound turned on.

STACK-ON PRODUCTS CO.

P.O. BOX 489, WAUCONDA, IL 60084

NOTE: is safe is designed to be mounted to a

shelf. Aaching the safe with a cable to a xed

object, as the sole means of securing the safe, will

compromise the safety and security of the safe.

SELECTING A LOCATION

IMPORTANT

Keep keys and your combination number in a secure

place, away from children. Keep this record of your serial

number and combination in a secure place separate from

your safe. To order a replacement key set, follow the

instructions on the aached form.

To secure the safe to a xed object, loop the cable

around the object and place the cable’s small end into

the key hole on the side of the safe while the drawer

is open. Locking the drawer will secure the cable end

in the safe.

SECURING THE SAFE WITH THE CABLE

SECURING THE SAFE WITH HARDWARE

Using the template, mark the holes to be used.

Drill 3/16” diameter pilot holes.

Install the rear screws so there is just enough room

between the head of the screw and the mounting

surface for the key slots. (Figure 2)

Slide the unit into place and secure the front

mounting holes with the screws and washers.

(Figure 3)

40706-1608 514

NOTE ON LOCKING THE SAFE: e safe

needs to be in an upright position, as shown in

gure 1, for the locking mechanism to function

properly. Failure to mount the safe in the

corrrect upright position will compromise the

safety and security of the safe

Figure 1

Figure 2

e safe is to be mounted to a shelf

. For optimal

safety and security, the safe should be installed in

an isolated, dry and secure area.

NOTE: is safe must be mounted to a shelf.

Failure to do so will compromise the safety and

security of the safe.

Figure 3

THE SAFE SHOULD ALWAYS BE KEPT

OUT OF THE REACH OF CHILDREN.

REINSTALLING THE DRAWER

To reinstall the drawer, align the drawer slide and push

the drawer in until it locks in place.

Key Request

“This is not a Registration Form”

Verification of ownership is required in order to receive replacement key for your security product.

In order to receive a replacement key to your security product:

1. Complete the following form and send to Stack-On Products.

2. Send a copy of your valid driver’s license along with the form.

3. Send a copy of the receipt showing the original purchase.

4. Security product owner must sign form.

5. Owner’s signature must be notarized.

6. Send $10.00 for replacement key. Personal Check, MasterCard, or Visa accepted.

7. Send completed information to:

Stack-On Products Company

1360 N. Old Rand Road

P.O. box 489

Wauconda, IL 60084

Serial Number______________________ Key Number (if applicable) _______

Unit Dimensions________________________________________

Unit Description___________________________________________________________

Owner’s Name ____________________________________ Date Purchased___/___/____

Owner’s Address ___________________________ Unit or Apt Number _________________

City ___________________________ State _______________ Zip Code________________

Telephone Number: (____)___________________ Fax Number: (____)___________________

Owner’s Email Address: ________________________________________________________

Owner’s Signature __________________________ Notary Signature________________

Notary Commission Expires: _____/_____/_____ Notary Stamp

SERVICE REQUESTED

Key Replacement: Yes No

$10.00 charge for this service

Credit Card Information (Please circle one) MasterCard Visa

Expiration Date: ___/___/___ Card Number:______________________________________

Credit Card Identification Number (Located on back of card, last 3 digits on signature strip)_________

9/07

NOTE: You can store your Key #, Serial # and Combination on Stack-On’s SECURE web site – stack-on.com under

Customer Service. Storing your Key # or Combination will provide instant access to this important information should you

ever lose your keys or your combination.

Only you will have access to this information.

40706-1608 614

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS

WHICH VARY FROM STATE TO STATE.

IN NO EVENT SHALL STACK-ON’S OBLIGATION UNDER THIS WARRANTY EXCEED THE PRICE

OF THE PRODUCT.

STACK-ON’S LIABILITY FOR ANY BREACH OF THIS WARRANTY SHALL BE LIMITED

EXCLUSIVELY TO REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT, AS DESCRIBED

ABOVE, OR A REFUND OF THE PURCHASE PRICE OF THE PRODUCT.

STACK-ON WILL NOT, UNDER ANY CIRCUMSTANCES, BE LIABLE TO THE INITIAL CONSUMER

FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL, EXEMPLARY, OR PUNITIVE DAMAGES

ARISING OUT OF THE PURCHASE OR USE OF ANY STACK-ON PRODUCTS, INCLUDING THE

SAFES.

THIS WARRANTY IS EXCLUSIVE AND EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES

EXPRESSED OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE, WHICH ARE HEREBY DISCLAIMED AND EXCLUDED. STACK-ON

SHALL NOT BE SUBJECT TO ANY OTHER OBLIGATIONS OR LIABILITIES. STACK-ON NEITHER

ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT, ANY OTHER LIABILITY

IN CONNECTION WITH THE SALE OF STACK-ON’S STEEL SAFES.

THIS WARRANTY DOES NOT COVER ANY PRODUCT, OR ANY PART OF ANY PRODUCT, WHICH

HAS BEEN SUBJECT TO EXCESSIVE USE, ACCIDENT, NEGLIGENCE, ABUSE OR MISUSE,

INCORRECT MAINTENANCE, ALTERATION OR REPAIR BY ANYONE OTHER THAN STACK-ON. IN

ADDITION, THIS WARRANTY DOES NOT COVER ANY ACCESSORIES OR PARTS USED WITH OR

IN THE PRODUCT WHICH ARE NOT INCLUDED WITH THE ORIGINAL PURCHASE.

If Stack-On is properly notified during the three-year warranty period and, after inspection confirms there

is a defect, Stack-On will, at its sole option, provide repair parts or exchange the product at no charge, or

refund the purchase price of the product.

Stack-On Products Company

1360 North Old Rand Road

Wauconda, IL 60084

[email protected]

If you believe there is a defect in material or workmanship in your Steel Safe during the three-year

warranty period, please contact our customer service department, by regular mail or email at the address

listed below, and include with your correspondence proof of purchase information and the model number

of the safe.

Stack-On Products Co. (“Stack-On”) Steel Safes are warranted to be free from defects in material and

workmanship for a period of three (3) years from the date of original purchase by a consumer. This

warranty extends to the initial consumer only.

LIMITED THREE YEAR WARRANTY

STEEL SAFES

40706-1608 714

Instrucciones

IMPORTANTE PARA COMENZAR

# Serie:

# Combinación Electrónica

NOTA: Usted puede almacenar su Numero de Llave y

su Nymero de Combinacion en el web site SEGURO

de - stack-on.com bajo la opcion que dice Customer

Servicio

Al almacenar su Numero de Llave y Numero de

Combinacion en este web site le proporcionara acceso

instantanio ha esta informacion importante en caso de

que usted pierda sus llaves o numero de combinacion.

Nadamas usted tendra acceso ha esta informacion

CARACTERISTICAS DE CONTROL

1. Cerradura con Llave

2. Botones de la combinación

3. Botón de reajuste

(adentro de la caja fuerte)

4. Compartimiento para las baterías/pilas

(adentro de la caja fuerte)

Cuando usted primero reciba su caja fuerte

usted tendra que abrir la puerta con las llaves

para instalar las baterías/pilas. Las

baterías/pilas vienen incluidas y están situadas

adentro de la su caja fuerte.

NOTA: Esta tecla también se ha proporcionado en

caso que usted pierde u olvida su código de

seguridad o las baterías se agotan. Si usted pierde su

llave, usted puede comprar una llave de reemplazo

reriéndose al número de serie situado en el frente

de la puerta. Vease las instruciones hacia el nal de

estas ojas con respecto a llaves de reemplazo.

Para abrir la caja fuerte con la llave inserte la llave en

la cerradura y de vuelta hacia la izquierda hasta que

la puerta se abra automáticamente. NOTA: Usted

debe dar vuelta de nuevo a la llave a la posición

original antes de que usted pueda cerrar y trabar la

puerta.

Registre tambien el número de combinación.

Registre el número de serie que aparece en la

etiqueta en frente de la puerta.

Mantenga las llaves y la combinación en un lugar seguro

lejos de los niños.

NO GUARDE LAS LLAVES O SU NUMERO DE

COMBINACIÓN ADENTRO DE LA CAJA FUERTE.

Herramientas necesarias:

perforar

Destornillador de cabeza plana

10 mm Llave

Taladro 3/16 "(5 mm) de bits para perforar madera

Hardware incluido:

(4) M6 x 20 mm (3/4 "de largo) Tornillos

(4) Arandelas

(4) anclajes de plástico

QAS-1510

40706-1608 814

PARA COMENZAR ELIMINANDO EL CAJÓN

ELIMINANDO EL CAJÓN

Quite el trazo de espuma alineando elcajón. Estire el

cajón hasta que esteabierto completamente

Localice el agujero de acceso. Usando un

destornillador pequeño o una herramienta

acentuada, mueva la lengüeta clara hacia la derecha y

estire el cajón de la diapositiva como se muestra.

Cuando usted primero reciba su caja/cajon fuerte

usted necesitará que abrir el cajón con la llave y

quitar el cajón para instalar las baterías/pilas. Las

baterías/pilas son incluidas y están situadas

adentro del cajón.

NOTA: Esta llave se le ha proporcionado en caso de

que usted pierda o olvide que su código de seguridad

o si las baterías/pilas estan bajas. Si usted pierde su

llave, usted puede comprar una llave de reemplazo

reriéndose al número de serie situado en el frente de

la puerta. Vease las instruciones hacia el nal de estas

ojas con respecto a llaves de reemplazo.

Para abrir la caja/cajón fuerte, inserte la llave en la

cerradura y de vuelta hacia la derecha hasta que el

cajón se abra automáticamente. NOTA: Usted debe

dar vuelta de nuevo a la llave a la posición original

antes de que usted pueda cerrar y trabar el cajon.

NOTA: Si la caja fuerte no esta montada, usted

puede tener acceso a la lengüeta alcanzando por

debajo del cajón y moviendo la lengüeta con su dedo.

Si la caja fuerte esta montada en una localización

donde el cajón se abre sobre una supercie sólida,

usted tendrá que quitar el cajón como se describe

anteriormente.

40706-1608 914

4. Compartimiento para las baterías/pilas

(adentro de la caja fuerte)

40706-1608 1014

NOTA: No mezcle las pilas nuevas con las vejas. No

mezcle las pilas alcalinas con las recargables.

INSTALACIÓN DE LAS PILAS

Para reinstalar el cajón, alinee’ los miembros de la

diapositiva del cajón y empuje el cajón hacia

adentro hasta que se trabe en su lugar. Instale las

(4) baterias/pilas de alcalino AA como se muestra.

Regrese la cubierta insertando las lengüetas

posteriores en las ranuras y precionando la cubierta

levemente en su lugar.

NOTA: Si las baterías/pilas estan bajas la luz roja se

encenderá mientras que la caja fuerte se este

abriendo. Substituya con 4 batarias/pilas nuevas de

alcalino AA como se muestra.

• Para su propia seguridad usted debe de

programar su propia combinación después de

abrir la caja fuerte.

• Anote esta nueva combinación en este

formulario ni guarde la combinación de nuestro

sitio web seguro en www.stack-on.com en

Servicio. Si usted escribe su combinación debe

mantener esta información en un lugar seguro,

lejos de los niños, no dentro de la caja fuerte.

PROGRAMADO SUS PROPIA

COMBINACIÓN ELECTRÓNICA

Ejemplo: (DERECHO) - (IZQUIERDO) -

(CENTRO) - (IZQUIERDO) - (DERECHO)

Botón de

reajuste

Pulse el botón Reset (3) situado en el interior de

la caja fuerte. Dos "pitidos" sonará (si el sonido

está activado) y los 3 botones parpadean azul dos

veces. Usted tendrá 5 segundos para comenzar a

introducir su combinación o tendrás que

empezar de nuevo.

Para cada entrada de la combinación de un

"bip" sonará (si el sonido está encendido) y

todos los botones se iluminan en verde. Si se

demora más de 5 segundos entre las entradas,

tendrá que empezar de nuevo desde el paso 1.

Una vez que haya terminado de introducir la

combinación, tendrá 5 segundos para presionar

el botón de reinicio para grabar su nueva

combinación o tendrás que empezar de nuevo

desde paso 1.

Escriba su propia combinación 3-8 botón

pulsando cualquier combinación de los 3

botones.

3. Al pulsar el botón de reinicio para grabar su

nueva combinación, habrá dos "pitidos" (si el

sonido está activado) y los 3 llaves parpadee

en azul dos veces, lo que indica que su nueva

combinación ha sido registrado.

Indice

Lingue:

Altri manuali Stack-On Sicuro

Stack-On

Stack-On Security Plus QAS-1310 Manuale utente

Stack-On

Stack-On PS-7-B Manuale utente

Stack-On

Stack-On E-48-MG-C-S Manuale utente

Stack-On

Stack-On PC-650 Manuale utente

Stack-On

Stack-On E-66-MB-E-S Manuale utente

Stack-On

Stack-On GCG-8RTA Manuale utente

Stack-On

Stack-On PFS-012-BG-E Manuale utente

Stack-On

Stack-On QAS-450-B Manuale utente

Stack-On

Stack-On TD-040-GP-E Manuale utente

Stack-On

Stack-On QAS-1514 Manuale utente

Stack-On

Stack-On PC-900-B Manuale utente

Stack-On

Stack-On PFWS-080-B-D-E Manuale utente

Stack-On

Stack-On PDS-1500 Manuale utente

Stack-On

Stack-On SHD-AOTT-BG-E Manuale utente

Stack-On

Stack-On QAS-1000 Manuale utente

Stack-On

Stack-On PC-95K-RTX Manuale utente

Stack-On

Stack-On QAS-1512 Manuale utente

Stack-On

Stack-On PS-1514 Manuale utente

Stack-On

Stack-On QAS-1512 Manuale utente

Stack-On

Stack-On Sentinel GCWB-18 Manuale utente

Stack-On

Stack-On QAS-1510-B Manuale utente

Stack-On

Stack-On SHD-AOTT-BG-B Manuale utente

Stack-On

Stack-On PS-15-20-B Manuale utente

Stack-On

Stack-On SECURITY PLUS Manuale utente

Manuali Sicuro popolari di altre marche

Squire

Squire Stronghold Keysafe Manuale utente

Phoenix

Phoenix FS0352C Scheda informativa del prodotto

Phoenix

Phoenix KS0030E Series Manuale utente

Vaultek

Vaultek 10 Series Scheda tecnica

Arregui

Arregui CLASS Manuale utente

Beaumont

Beaumont SMART KEYBOX Manuale utente

Honeywell

Honeywell 2077D - 1.21 Cubic Foot Anti-Theft Safe Manuale utente

Hornady

Hornady SnapSafe Trunk Safe II Manuale utente

SPORTS AFIELD

SPORTS AFIELD SA-HD5-BIO Manuale utente

Honeywell

Honeywell 5912 Manuale utente

Phoenix

Phoenix FS1280F Manuale utente

Phoenix

Phoenix SS0992K Scheda informativa del prodotto

Technomax

Technomax Trony Series Manuale

SPORTS AFIELD

SPORTS AFIELD INSTINCT BIOMETRIC Series Manuale utente

RICHTER CZECH

RICHTER CZECH LA Manuale operativo

Olymp

Olymp GOsafe 110 Manuale utente

Phoenix

Phoenix SS0100E Scheda informativa del prodotto

Clarke

Clarke Strong-Arm CS1000K Manuale di istruzioni