Stage right 600059 Manuale utente
200-Channel UHF Dual Wireless Microphone
P/Ns 600059, 600060, 600061
User's Manual
2
SAFETY WARNINGS AND GUIDELINES
Please read this entire manual before using this device, paying extra
attention to these safety warnings and guidelines. Please keep this
manual in a safe place for future reference.
•This device is intended for indoor use only.
•Do not expose this device to water or moisture of any kind. Do
not place drinks or other containers with moisture on or near the
device. If moisture does get in or on the device, immediately
remove it from its power source and allow it to fully dry before
reapplying power.
•Do not touch the device, the power cord, or any other connected
cables with wet hands.
•Do not install this device on an unstable surface where it could fall
and cause either personal injury or damage to the device and/or
other equipment.
•Do not expose this device to excessive vibration or extreme force,
shock, or fluctuations in temperature or humidity.
•Do not expose this device to excessively high temperatures. Do
not place it in, on, or near a heat source, such as a fireplace, stove,
radiator, etc. Do not leave it in direct sunlight.
•This device ventilates excessive heat through the slots and
openings in the case. Do not block or cover these openings.
Ensure that the device is in an open area where it can get
sufficient airflow to keep from overheating.
3
•Do not place or install this device in an area where it can be
exposed to excessive amounts of dust, humidity, oil, smoke, or
combustible vapors.
•Use only in a well-ventilated area. Do not use in close, confined
spaces.
•Prior to operation, check the unit and power cord for physical
damage. Do not use if physical damage has occurred.
•Unplug this device from the power source when not in use.
•Take care to prevent damage to the power cord. Do not allow it
to become crimped, pinched, walked on, or become tangled with
other cords. Ensure that the power cord does not present a
tripping hazard.
•Never unplug the unit by pulling on the power cord. Always grasp
the connector head or adapter body.
•Ensure that power is turned off and disconnected before making
any electrical connections.
•Remove the batteries from the microphones/bodypacks if they
will go unused for a lengthy period of time.
•Do not mix new and old batteries or batteries of different types.
•Clean using a soft, dry cloth only. Do not use chemical cleaners,
solvents, or detergents. For stubborn deposits, moisten the cloth
with warm water.
•This device has no user serviceable parts. Do not attempt to open,
service, or modify this device.
4
CUSTOMER SERVICE
The Monoprice Customer Service department is dedicated to ensuring
that your ordering, purchasing, and delivery experience is second to none.
If you have any problem with your order, please give us an opportunity to
make it right. You can contact a Monoprice Customer Service
representative through the Live Chat link on our website
www.monoprice.com or via email at s[email protected]. Check the
website for support times and links.
PACKAGE CONTENTS
Please take an inventory of the package contents to ensure you have all
the items listed below. If anything is missing or damaged, please contact
Monoprice Customer Service for a replacement.
1x Receiver
2x Receiver Antennas
2x Handheld Microphones (600059 only)
2x Bodypack Transmitters (600060 and 600061 only)
2x Headset Microphones (600060 only)
2x Lavalier Microphones (600061 only)
1x AC Power Adapter
1x User's Manual
5
PRODUCT OVERVIEW
Receiver Front Panel
1. I.R.: IR receiver.
2. A▲/▼: Up and Down buttons for Channel A. Momentarily press
either button to increase or decrease the volume level. Press the
SET Abutton and the A▲button at the same time to lock or
unlock the front panel controls for Channel A.
3. A SET: SET button for Channel A. Press the button one time to
initiate IR synchronization. Press the button two times to scan for
available frequencies. Press the button three time to manually set
the frequency. Press the SET A button and the A▲button at the
same time to lock or unlock the front panel controls for Channel A.
4. B SET: SET button for Channel B. Press the button one time to
initiate IR synchronization. Press the button two times to scan for
available frequencies. Press the button three time to manually set
the frequency. Press the SET B button and the B▲button at the
same time to lock or unlock the front panel controls for Channel B.
5. B▲/▼: Up and Down buttons for Channel B. Momentarily press
either button to increase or decrease the volume level. Press the
6
SET B button and the B▲button at the same time to lock or
unlock the front panel controls for Channel B.
6. POWER: Momentarily press the POWER button to turn the
Receiver on. Press and hold the POWER button for 2 seconds to
turn the Receiver off.
Receiver Rear Panel
7. ANT B/ANT A: Antenna BNC connector for Channel B and Channel
A.
8. BALANCED B/BALANCED A: The XLR jacks output a balanced
signal for Channel B and Channel A.
9. MIX OUT: The 1/4" TRS jack outputs an unbalanced signal with a
mix of Channel A and Channel B.
10. DC INPUT: DC barrel connector for connecting the included AC
power adapter.
7
Receiver Display
1. RF LEVEL: The meter displays the strength of the RF signal from
the Handheld Microphone (600059 only) or the Bodypack
Transmitter (600060 and 600061 only).
2. AF LEVEL: The meter displays the audio signal level in decibels
(dB). The loudest signals should hit the 0element. If the PEAK
element illuminates, the signal is being distorted and the volume
level should be reduced using the ▲/▼buttons on the Receiver.
3. MUTE: The output of the Handheld Microphone (600059 only) or
the Bodypack Transmitter (600060 and 600061 only) is muted
when the icon is displayed.
4. FREQUENCY: Displays the frequency being used to communicate
with the Handheld Microphone (600059 only) or the Bodypack
Transmitter (600060 and 600061 only).
5. LOCK: All settings are locked when the icon is displayed.
8
Handheld Microphone (600059 only)
1. Microphone Head
2. Microphone Body
3. IR: IR interface.
4. Display
5. Power/Mute Button: Momentarily press the button to turn the
Handheld Microphone on or off. Press and hold the button for
several seconds to turn MUTE on or off.
6. Battery Cover: Unscrew the cover and remove it to access the
battery compartment.
7. Battery Compartment Cover: Open the cover to access the
Battery Compartment.
9
Handheld Microphone Display (600059 only)
1. Frequency: Displays the frequency being
used to connect to the Receiver.
2. Battery: Displays the battery charge level.
Bodypack Transmitter (600060 and 600061 only)
1. MIC/LINE: 3.5mm jack for connecting
the microphone.
2. MUTE: Slide the switch to turn audio
mute on or off.
3. Antenna
4. Display
5. Power LED: Illuminates green when
the Bodypack Transmitter is powered
on.
6. Battery Level LED: Illuminates red
when the battery level is low.
7. Power Button: Press the button to
turn the Bodypack Transmitter on or off.
8. I.R.: IR interface.
9. ▲/▼: Up and Down rocker button.
10. SET Button
11. Battery Compartment
10
12. Battery Compartment Cover
13. Battery Compartment Cover Release Buttons: Press the buttons
on each side of the Battery Compartment Cover to open it.
Bodypack Transmitter Display (600060 and 600061 only)
1. Frequency: Displays the
frequency used to connect to the
Receiver.
2. Battery: Displays the battery
charge level.
3. Channel: Displays the Channel used to connect to the receiver.
4. Identity: Displays the ID used to identify the Bodypack
Transmitter.
5. Sensitivity: The Sensitivity is set at the factory and cannot be
changed.
SETUP AND OPERATION
Receiver
1. Place receiver in a location close to where the performance will
take place. Ensure that it is at least 5 feet (1.5 meters) from any
large metal objects or wall/ceiling structure to ensure a strong RF
signal.
2. Connect the two antennas to the ANT A and ANT B connectors on
the rear panel.
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Stage right Microfono
