Stahl ISpac 9182 Series Manuale utente
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
Manual
Additional languages www.r-stahl.com
EN
Temperature transmitter Ex i
Series 9182
2
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
Temperature transmitter Ex i
Series 9182
Contents
1 General Information ............................................................................................3
1.1 Manufacturer .......................................................................................................3
1.2 Information about the Manual .............................................................................3
1.3 Further Documents .............................................................................................3
1.4 Conformity with Standards and Regulations .......................................................3
2 Explanation of the Symbols ................................................................................4
2.1 Symbols used in this Manual ..............................................................................4
2.2 Warning Notes ....................................................................................................4
2.3 Symbols on the Device .......................................................................................5
3 Safety Notes .......................................................................................................5
3.1 Storage of the Manual .........................................................................................5
3.2 Personnel Qualification .......................................................................................5
3.3 Safe Use .............................................................................................................6
3.4 Modifications and Alterations ..............................................................................7
4 Function and Device Design ...............................................................................7
4.1 Function ..............................................................................................................7
4.2 Device Design .....................................................................................................8
5 Technical Data ....................................................................................................9
6 Engineering .......................................................................................................19
7 Transport and Storage ......................................................................................19
8 Mounting and Installation ..................................................................................20
8.1 Dimensions / Fastening Dimensions .................................................................20
8.2 Mounting / Dismounting, Operating Position .....................................................21
8.3 Installation .........................................................................................................24
9 Parameterization and Commissioning ..............................................................30
9.1 Replacement of the Device ...............................................................................30
9.2 Parameterizations .............................................................................................30
9.3 Commissioning .................................................................................................37
10 Operation ..........................................................................................................37
10.1 Operation ..........................................................................................................37
10.2 Indications .........................................................................................................37
10.3 Troubleshooting ................................................................................................38
11 Maintenance, Overhaul, Repair ........................................................................38
11.1 Maintenance .....................................................................................................38
11.2 Overhaul ...........................................................................................................39
11.3 Repair ...............................................................................................................39
11.4 Returning the Device ........................................................................................39
12 Cleaning ............................................................................................................40
13 Disposal ............................................................................................................40
14 Accessories and Spare Parts ...........................................................................40
9182602330
2018-03-16·HB00·III·en·02
General Information
3
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
Temperature transmitter Ex i
Series 9182
1 General Information
1.1 Manufacturer
R. STAHL Schaltgeräte GmbH
Am Bahnhof 30
74638 Waldenburg
Germany
Phone: +49 7942 943-0
Fax: +49 7942 943-4333
Internet: www.r-stahl.com
E-Mail: [email protected]
1.2 Information about the Manual
ID-No.: 9182602330
Publication Code: 2018-03-16·HB00·III·en·02
Hardware version: B, C
Software version: 01-09 or higher
The original instructions are the English edition.
They are legally binding in all legal affairs.
1.3 Further Documents
• Cabinet installation guide
• Brief instructions for module parameterising with ISpac Wizard
(see ISpac Wizard software)
• FMEDA reports "STAHL 07/07-23 R016" and "STAHL 07/07-23 R017"
• Safety manual 9182 Ex i
• Data sheet 9182 Ex i
• Operating instructions 9182 Ex i
For documents in additional languages, see www.r-stahl.com.
1.4 Conformity with Standards and Regulations
See certificates and EC Declaration of Conformity: www.r-stahl.com.
The device has IECEx approval. See IECEx homepage: http://iecex.iec.ch/
Further national certificates can be downloaded via the following link:
https://r-stahl.com/en/global/products/support/downloads/.
Explanation of the Symbols
49182602330
2018-03-16·HB00·III·en·02
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
Temperature transmitter Ex i
Series 9182
2 Explanation of the Symbols
2.1 Symbols used in this Manual
2.2 Warning Notes
Warnings must be observed under all circumstances, in order to minimize the risk due to
construction and operation. The warning notes have the following structure:
• Signalling word: DANGER, WARNING, CAUTION, NOTICE
• Type and source of danger/damage
• Consequences of danger
• Taking countermeasures to avoid the danger or damage
Symbol Meaning
Tips and recommendations on the use of the device
Danger due to explosive atmosphere
DANGER
Danger to persons
Non-compliance with the instruction results in severe or fatal injuries to
persons.
WARNING
Danger to persons
Non-compliance with the instruction can result in severe or fatal injuries
to persons.
CAUTION
Danger to persons
Non-compliance with the instruction can result in light injuries to
persons.
NOTICE
Avoiding material damage
Non-compliance with the instruction can result in material damage to the device
and / or its environment.
9182602330
2018-03-16·HB00·III·en·02
Safety Notes
5
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
Temperature transmitter Ex i
Series 9182
2.3 Symbols on the Device
3 Safety Notes
3.1 Storage of the Manual
• Read the manual carefully.
• Store the manual at the mounting location of the device.
• Observe applicable documents and operating instructions of the devices to be
connected.
3.2 Personnel Qualification
Qualified specialist personnel are required to perform the tasks described in this manual.
This primarily applies to work in the following areas:
• Project engineering
• Mounting/dismounting the device
• (Electrical) installation
• Commissioning
• Maintenance, repair, cleaning
Specialists who perform these tasks must have a level of knowledge that meets
applicable national standards and regulations.
Additional knowledge is required for tasks in hazardous areas! R. STAHL recommends
having a level of knowledge equal to that described in the following standards:
• IEC/EN 60079-14 (Electrical installations design, selection and construction)
• IEC/EN 60079-17 (Inspection and maintenance of electrical installations)
• IEC/EN 60079-19 (Equipment repair, overhaul and reclamation)
Symbol Meaning
05594E00
CE marking in accordance with the current applicable directive.
02198E00
Electrical circuit certified for hazardous areas according to the marking.
15649E00
Input
15648E00
Output
11048E00
Safety instructions that must always be observed: For devices with this
symbol, the corresponding data and/or the safety-relevant instructions
contained in this manual must be observed!
Safety Notes
69182602330
2018-03-16·HB00·III·en·02
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
Temperature transmitter Ex i
Series 9182
3.3 Safe Use
Before assembly
• Read and observe the safety notes in this manual.
• Ensure that the contents of this manual are fully understood by the personnel in
charge.
• Use the device in accordance with its intended and approved purpose only.
• Always consult with R. STAHL Schaltgeräte GmbH if using the device under operating
conditions not covered by the technical data.
• Make sure that the device is not damaged.
• We are not liable for damage caused by incorrect or unauthorised use of the device or
by non-compliance with this manual.
For mounting and installation
• Have mounting and installation performed only by qualified and authorised persons
(see "Qualification of the personnel" section).
• The device is only to be installed in zones for which it is suited based on its marking.
• During installation and operation, observe the information (characteristic values and
rated operating conditions) on the rating, data and information plates located on the
device.
• Before installation, make sure that the device is not damaged.
• When the 9182/.0-59-1. type variants are used, the maximum voltages and load
resistances must be considered.
• When used in Zones 2 and 22, the intrinsically safe devices of Zones 1, 0, 21 and
20 can be connected to the intrinsically safe signal circuits.
• The safety characteristic values of the connected field devices must correspond to the
specifications in the data sheet or in the EU Type Examination Certificate.
• Interconnecting several devices in a single intrinsically safe circuit can result in
different safety characteristic values. This may impair intrinsic safety!
• Electrical circuits with the "Ex i" type of protection can no longer be operated as circuits
with this protection type after being operated with circuits with other types of protection.
Commissioning, maintenance, repair
• Only have commissioning and repairs performed by qualified and authorised persons
(see "Personnel qualification" section).
• Before commissioning, make sure that the device is not damaged.
• Only perform maintenance work described in this manual.
• Repair work on the devices must be performed only by R.STAHL Schaltgeräte GmbH.
• For SIL applications observe the safety manual and FMEDA reports.
9182602330
2018-03-16·HB00·III·en·02
Function and Device Design
7
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
Temperature transmitter Ex i
Series 9182
3.4 Modifications and Alterations
4 Function and Device Design
4.1 Function
Application range
The temperature transmitter is used for intrinsically safe operation of temperature
sensors or resistance transmitters. Virtually all conventional sensors, such as Pt100,
Pt500, thermocouples and potentiometers, can be connected.
Mode of operation
The parameters of the device can be adjusted using the ISpac Wizard software or
alternatively by means of a DIP switch (only with Type 9182/.0-5.-11).
DANGER
Explosion hazard due to modifications and alterations to the device!
Non-compliance results in severe or fatal injuries.
• Do not modify or alter the device.
No liability or warranty for damage resulting from modifications and
alterations.
DANGER
Explosion hazard due to improper use!
Non-compliance results in severe or fatal injuries.
• The device may only be used according to the operating conditions
described in this manual.
• Use the device only for the intended purpose specified in this
manual.
Function and Device Design
89182602330
2018-03-16·HB00·III·en·02
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
Temperature transmitter Ex i
Series 9182
4.2 Device Design
#Device component Description
07451E00
1 Black/
green terminals
Connection terminals for the safe area
2 "PWR" LED, green Auxiliary power indication
3 "LF1" LED, red Indication of line fault detection for channel 1
4 "LF2" LED, red Indication of line fault detection for channel 2
5 DIP switch "LF1" Reset activation of the line fault detection and
anti-pumping device of the limiting value for
channel 1
6 DIP switch "ADJ1" Adjustment of line resistance in channel 1
7 DIP switch "LF2" Reset activation of the line fault detection and
anti-pumping device of the limiting value for
channel 2
8 DIP switch "ADJ2" Adjustment of line resistance in channel 2
9 Blue terminals Connection terminals for the hazardous area
(intrinsically safe Ex i)
10 Parameterization
interface
Configuration of the device by means of
ISpac Wizard software Type "9199"
11 "A" and "B" LED,
yellow
Indication for limit contacts for channel 1
18 "A" and "B" LED,
yellow
Indication for limit contacts for channel 2
1
9
2
5
7
4
3
6
8
10
11
18
9182
9182602330
2018-03-16·HB00·III·en·02
Technical Data
9
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
Temperature transmitter Ex i
Series 9182
5 Technical Data
Marking
Type designation 9182/.0-5.-1.
CE marking C0158
Explosion Protection
Version for all types 9182/.0-5.-1.
Global (IECEx)
Gas IECEx BVS 09.0046X
Ex nA nC [ia Ga] IIC T4 Gc
[Ex ia Da] IIIC
Europe (ATEX)
Gas and dust DMT 02 ATEX E 243 X
E II 3 (1) G Ex nA nC [ia Ga] IIC T4 Gc
E II (1) D [Ex ia Da] IIIC
Certifications and certificates
Certificates IECEx, ATEX, Brazil (INMETRO), India (PESO), Canada (cFM),
Kazakhstan (TR), Korea (KTL), Russia (TR), USA (FM, UL),
Belarus (TR)
Ship approval DNV GL
Safety data
Max. voltage Uo6.5 V
Max. current Io19.7 mA
Max. power Po32 mW (linear characteristic)
Max. connectable
capacitance Co
IIC 25 mF
IIB 570 mF
Max. connectable
inductance Lo
IIC 90 mH
IIB 330 mH
Internal
capacitance Ci
negligible
Internal inductance Linegligible
Safety-related
maximum voltage
253 V
Technical Data
10 9182602330
2018-03-16·HB00·III·en·02
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
Temperature transmitter Ex i
Series 9182
Functional safety (IEC 61508)
Version 9182/10-51-13, SIL 2
Test report Exida FMEDA Stahl 07/07-23-R016
Max. SIL 2
Safe Failure Fraction
SFF
78%
MTBF 120 years
PFDAVG at T[Proof]
Further information see safety manual and test report
Version 9182/10-51-14, SIL 2
Test report Exida STAHL 07/07-23 R016 and STAHL 07/07-23 R017
Max. SIL 2
Safe Failure Fraction
SFF
MTBF
PFDAVG at T[Proof]
Further information see safety manual and test report
T[Proof] 1 year 3 years 5 years 10 years
PFDAVG 1.31 x 10-3 2.54 x 10-3 3.77 x 10-3 6.86 x 10-3
4 to 20 mA Limit contact Parallel limit contact
78% 78.4% 81.1%
4 to 20 mA Limit contact Parallel limit contact
120 years 114 years 114 years
4 to 20 mA Limit contact Parallel limit contact
1 year 1.31 x 10-3 1.14 x 10-3 9.72 x 10-4
2 years 2.54 x 10-3 2.22 x 10-3 1.89 x 10-3
5 years 3.77 x 10-3 3.30 x 10-3 2.80 x 10-3
10
years
6.86 x 10-3 5.99 x 10-3 5.09 x 10-3
Altri manuali per ISpac 9182 Series
1
Indice
Altri manuali Stahl Trasmettitore
Stahl
Stahl 9162 Series Manuale utente
Stahl
Stahl ISpac 9162 Manuale utente
Stahl
Stahl ISpac 9146 Series Manuale utente
Stahl
Stahl 9162 Series Manuale utente
Stahl
Stahl 9146 Series Manuale utente
Stahl
Stahl 9182 Series Manuale utente
Stahl
Stahl 9146 Series Manuale utente
Stahl
Stahl ISpac 9182 Series Manuale utente
Stahl
Stahl ispac 9160 Manuale utente
