Standa 8SMC1-USBhF Guida all'installazione

8SMC1-USBhF stepper motor controller. Quick start user guide

8SMC1-USBhF

1.5A Microstep Driver with USB Interface

Quick start user guide

Note: Information in this quick start user guide is believed to be accurate and reliable. However no

responsibility is assumed for the consequences of its use or for any infringement of patents or other right of

third parties which may result from it’s use. Specifications are subject to change without notice.

Note: Windows are registered trademark of Microsoft Corporation, LabVieW and NI VISA is registered

trademark of National Instruments Inc. All other products and corporate names appearing in this manual may

or may not be registered or copyrights of their respective companies, and are used only for identification or

explanation and to the owner’s benefit, without intent to infringe.

1/14/2008 www.standa.lt Page 1 of 8

8SMC1-USBhF stepper motor controller. Quick start user guide

Index

1Introduction.....................................................................................................................................2

2System requirements.....................................................................................................................2

3Software installation.......................................................................................................................2

3.1 Other software installation....................................................................................................3

4Hardware installation.....................................................................................................................3

4.1 Equipment which is necessary for successful installation................................................3

4.2 Connection...............................................................................................................................4

5First start..........................................................................................................................................5

5.1 First connection to PC............................................................................................................5

5.2 First start with SMCVieW.......................................................................................................6

6More detailed information.............................................................................................................8

1Introduction

Congratulations on your purchase of the 8SMC1-USBhF stepper motor controller. This

Quick start user guide describes how to set up and start the 8SMC1-USBhF stepper motor

controller. Refer to the 8SMC1-USBhF User Manual (PDF file) for more detailed information

about the operation and programming of the 8SMC1-USBhF stepper motor controller.

2System requirements

8SMC1-USBhF is designed to work with your personal computer (PC) using Microsoft

Windows 2000/XP/Vista operation systems or mobile devices with Microsoft Windows Mobile

5.0 and higher. Presence of the USB 2.0 or 1.1 compatible host port on your host device is

necessary.

8SMC1-USBhF can operate with bipolar stepper motors according to the technical

specification and wiring requirements. Maximum allowable average phase current is 1.5A,

rated voltage is 40V.

3Software installation

Use this section to get software installation quickly. Refer to the User Manual 4.1 for

more detailed information.

Make sure that all 8SMC-USBhF devices are unplugged and switched off. Turn on

computer. Insert the CD-ROM labeled “8SMC-USBhF” in your CD-ROM drive or download the

latest software from www.standa.lt, unzip “8SMC1-USB(h) Soft.zip” software package and

open main folder. Open ”SMCVieW and VISA driver” folder and run setup.exe and following

to Installation Wizard instructions (see Figure 1).

1/14/2008 www.standa.lt Page 2 of 8

8SMC1-USBhF stepper motor controller. Quick start user guide

Figure 1. Software installation.

3.1 Other software installation

For information of other software installations (for programming 8SMC1-USBhF

controller on C, C++, Basic, Delphi, MatLab and other languages excluding LabVieW) refer to

the User Manual.

4Hardware installation

4.1 Equipment which is necessary for successful installation

Note: All 8SMC1-USBhF controllers that are delivered with motorized stages are equipped

with correct current sensing resistors. All other 8SMC1-USBhF controllers are equipped with 2

Ohm current sensing resistors for stepper motors, where rated current is 400 mA (unless

another is specified).

−USB A-B cable. It connects 8SMC1-USBhF to PC. Use only operable USB cables!

Defective USB cables may cause the 8SMC1-USBhF to malfunction.

−Stabilized DC power supply with 2 mm central pin connector. Dimensions and polarity

are shown on Figure 2 and Figure 3. Power supply rated current must exceed average

stepper motor rated current, by no less than two times. Power supply must never exceed

40V. Power driver can be damaged if higher voltages are applied.

−Motorized stage. If you use third party motorized stages or stepper motors, make sure

that current sensing resistors installed in 8SMC1-USBhF correspond to stepper motor

rated current. For more information see User Manual 2.1 and 4.2.

−Stage to controller cable. It connects 8SMC1-USBhF to translational or rotational

stage. This cable is plugged to 8SMC1-USBhF by standard 15 Pin DSub connector

according to Figure 4. If you use handmade motorized stage to controller cable make

sure that it configures with Figure 4 and there is no contact between stepping motor

phase windings and 8SMC1-USBhF ground. The power driver will be damaged if such

grounding present.

1/14/2008 www.standa.lt Page 3 of 8

8SMC1-USBhF stepper motor controller. Quick start user guide

Figure 2. Power In connector. Dimensions.

Figure 3. Power In connector. Pinout.

Figure 4. Wiring diagram.

4.2 Connection

−Make sure that DC power supply is off.

−Use 'Stage to controller cable' to connect motorized stage to 15-pin connector on 8SMC1-

USBhF front panel (see Figure 5).

−Connect DC power supply to Power connector on 8SMC1-USBhF front panel.

−Switch the DC power supply on.

−Use ‘USB A-B cable’ to connect PC to USB connector on 8SMC1-USBhF front panel.

Figure 5. 8SMC1-USBhF Stepper motor controller front panel

1/14/2008 www.standa.lt Page 4 of 8

8SMC1-USBhF stepper motor controller. Quick start user guide

5First start

Note: Next first start is shown for Windows XP. For information about first start on

Windows Vista see User Manual 4.4.

5.1 First connection to PC

Figure 6. Hardware wizard 1st screen

Windows New Hardware Wizard will start after first connection of 8SMC1-USBhF

controller to PC. Wait while Windows will find a new hardware and install driver for it.

Depending on a Windows version it may pass automatically or demand to pass several steps:

oThe main window of the Hardware Wizard will appear (see Figure 6). Choose ”No, not

this time” and press the “Next>” button. On some old versions of Windows XP this screen

might be skipped.

Figure 7. Hardware wizard 2nd screen

oChoose (see Figure 7) Install the software automatically (Recommended) and press the

“Next>” button. Wait until installation is completed and press “Finish” button (see Figure

9).

1/14/2008 www.standa.lt Page 5 of 8

8SMC1-USBhF stepper motor controller. Quick start user guide

Figure 8. Hardware wizard 3rd screen

oIf other 8SMC1-USBhF controllers were installed on computer earlier, screen Figure 8 may

appear. Choose 8SMC1-USB.inf and press “Next” button.

Figure 9. Hardware wizard last screen

5.2 First start with SMCVieW

SMCVieW is a friendly graphical user interface for control, monitoring and tuning your

stepping motors. It can also be used for easy setup and save/load of all parameters for each

stepping motor. Interface supports up to 30 drivers simultaneously. Use this section to start

with SMCVieW quickly. Refer to the User Manual 5 for more detailed information.

Turn the power of stepping motor controller on. Press “Start”, choose “Programs”

group, then “SMCVieW” subgroup and “SMCVieW” application. After start screen like the one

on Figure 10 will appear.

Figure 10. SMCVieW main screen. No 8SMC1-USBhF drives found

1/14/2008 www.standa.lt Page 6 of 8

8SMC1-USBhF stepper motor controller. Quick start user guide

Press “REFRESH” button. All available 8SMC1-USBhF devices will be found. Interface

can represent up to three devices simultaneously. If more than three 8SMC1-USBhF devices

are used at the same time, slider is displayed at the left side of SMCVieW interface (see

Figure 11).

Figure 11. SMCVieW main screen. Four 8SMC1-USBh drives found

Open Setup and choose Positioner window (see Figure 12). This window is used for

loading a set of installation-specific settings for the selected positioner. Choose the

Manufacturer, Model name and appropriate wiring diagram. Press Load Button when

selection is made. All fields of “Setup” will be changed to the values specific for your

positioner.

Figure 12. Positioner setup screen

Then close Setup and press Reset to button (see Figure 11). Stage calibration will be

performed using predefined data for stage that you choose in Setup->Positioner window.

Controller is ready to work.

1/14/2008 www.standa.lt Page 7 of 8

8SMC1-USBhF stepper motor controller. Quick start user guide

For running stage choose appropriate speed (see Figure 13) and destination position

(Figure 14) and press START button.

Figure 13.

Figure 14.

6More detailed information

Use this Quick start user guide for quick start only. Refer to the User Manual for more

detailed information.

1/14/2008 www.standa.lt Page 8 of 8

Altri manuali per 8SMC1-USBhF

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Standa Azionamento CC

Standa

Standa FBC1LD Manuale utente

Manuali Azionamento CC popolari di altre marche

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Manuale utente

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Manuale elenco delle parti

Chamberlain Garog

Chamberlain Garog D Series Manuale utente

Parker

Parker PDS Series Manuale utente

Festo

Festo DGC G Series Guida all'installazione

Binks

Binks QS-5012-1-CE Manuale utente

Danfoss

Danfoss VLT 2800 Series Scheda tecnica

ABB

ABB ACQ580-01 Series Manuale di installazione

YASKAWA

YASKAWA CANopen SI-S3 Manuale utente

GE D20A6 Manuale utente

Unex

Unex MC-D-250-1000-050W-TW Manuale utente

Geckodrive

Geckodrive G213V Manuale utente

ABB

ABB RSYC-01 Manuale utente

Rockwell Automation

Rockwell Automation PowerFlex 700S Manuale del proprietario

WEG

WEG DeviceNet CFW500 Manuale utente

Siemens

Siemens SINAMICS G Scheda tecnica

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Istruzioni operative

SOMFY

SOMFY JR RU 30 Manuale utente