Stanley Fat Max S2 Manuale utente
77-188
77-198
INSTRUCTION MANUAL
MANUEL D’INSTRUCTIONS
MANUAL DE INSTRUCCIONES
2 • S2/S2XL
Fig. 2
Fig. 1
MODELS
S2 Laser Level & Square
S2XL Hi Powered Laser Level &
Square, with Precision
Machined Aluminum Base.
FEATURES
(Fig. 1)
1. Single button operation– ON|OFF
2. Dual-beam laser projects both horizontal
and vertical (90º reference) laser “chalk-
lines” on surface
3. Push buttons used for non-abrasive vertical mounting;
Mounts to surface using adhesive putty (included)
4. Precise leveling vials
5. T-Edge on base to align laser to surface edge
6. 90º layout guide– calculate and turn angles in
5º increments
OPERATION
Ideal for use with all projects and carpentry work including
tiles, paneling, dry wall, outlet switches
Horizontal Applications (Fig. 2)
Set the unit on a flat surface. Use the T-Edge to square unit to
any surface with a 90º reference for aligning or plumbing.
Vertical Applications
To attach to vertical surface, apply a small portion of adhesive
putty to push pads (Fig.3). Align instrument using horizontal
leveling vials. Firmly press push buttons to attach unit to
surface. (Fig.4).
S2/S2XL • 3
EN
ENGLISH
CALIBRATION
This instrument is factory calibrated and should never need
field calibration. Calibration should be performed only by an
authorized service center. Contact CST/berger, a division of
Stanley Works™ Customer Service at US (815)432-9200.
SAFE OPERATING PROCEDURES
Working safely with this instrument is possible only when the
operating and safety information is read completely and the
instructions contained therein are strictly followed. Do not
remove the label on the side of the housing.
Use in combination with other optical instruments,
manipulations or in other applications other than described
here, can lead to dangerous laser output.
Do not stare into the laser lines.
Do not direct the laser lines at other persons.
4 • S2/S2XL
Fig. 3 Fig. 4
CERTIFICATIONS
This laser complies with all applicable portions of title 21
of the Code of Federal Regulations set by the Food and Drug
Administrations, Center for Devices, and Radiological Health.
Complies with 21CFR 1040.10 and 10040.11 except for devations
pursuant to Laser notice No. 50,
dated July 26, 2001.
This Laser tool has also been tested and complies with the CE
certification requirements set forth in the EC regulations
89/336/EEC and EN 61000-6-1 (EN50082-1), EN 61000-6-3
(EN50081-1) and EN 60825-1.
POWER
Open the battery cover by releasing the battery door clip on the
bottom of the housing. If replacing batteries, remove the
existing batteries. Insert three “AA” batteries into the laser tool.
Be sure to check for battery polarity, as indicated inside the
battery housing.
Note: Refer to Electrical Safety Procedures prior to replacing
the batteries.
Alkaline batteries offer the longest battery life when used in
this laser tool.
Note: Extreme temperatures and the use of batteries with
different levels of charge can reduce the operating time of the
laser tool. Always use batteries with the same power rating and
from the same manufacturer. For the proper disposal of the
used batteries, see the section “Environmental Protection”.
ELECTRICAL SAFETY PROCEDURES
WARNING: Batteries can explode or leak, and can
cause injury or fire. To reduce this risk:
ALWAYS follow all instructions and warnings on the battery
label and package.
DO NOT short any battery terminals.
S2/S2XL • 5
DO NOT charge alkaline batteries.
DO NOT mix old and new batteries. Replace all of them at the
same time with new batteries of the same brand and type.
DO NOT mix battery chemistries.
DISPOSE of batteries per local code.
DO NOT dispose of batteries in fire.
KEEP batteries out of reach of children.
REMOVE batteries if the device will not be used for
several months.
ENVIRONMENT PROTECTION
Recycle raw materials & batteries instead of disposing
of waste. The unit, accessories, packaging & used batteries
should be sorted for environmentally friendly recycling in
accordance with the latest regulations.
SPECIFICATIONS
6 • S2/S2XL
Weight 1.0 lbs (0.45kg)
Accuracy
Laser Diode
1/2-inch @ 30' 1/4-inch @ 60'
15 Hours - 3" AA" Batteries 1.5 V
635-670 nm 635 nm
Range 30 FT 100 FT
Power
Operating Temperature 32º F to 104ºF
(0ºC to 40ºC)
S2 S2XL
Depending Upon Ambient Light Conditions
WARRANTY
The S2 and S2XL is warranted to the original purchaser to be
free from defects in workmanship and material. Stanley Works
will repair or replace any defective part which may malfunction
under normal and proper use within a period of ninety (90) days
for the S2, or one (1) year for the S2XL from the date of
purchase without charge of parts and labor, once delivered and
shipped prepaid to CST/berger, division of Stanley Works,
together with proof of date and place of purchase.
CST/berger
division of Stanley Works
255 W. Fleming Street
Watseka, IL 60970
ph: (815) 432-9200
This warranty is not subject to misuse, abuse, assignment or
transfer. The exclusive remedy under any and all warrants and
guarantees, expressed or implied, is limited to repair and/or
replacement as provided herein, and Stanley shall not be liable
for damages from loss or delay of equipment uses, consequen-
tial or incidental damage. Subject to change without notice.
S2/S2XL • 7
CARACTERÍSTICAS
1. Operación con un sólo botón –
“ON | OFF”
2. El láser de doble rayo proyecta
“líneas de tiza” en láser tanto horizontal como vertical
(referencia de 90°)
3. Dos botones de oprimir para montaje vertical; incluye
cintas adhesivas para montaje
4. Ampolletas de nivelación precisas
5. Borde en T sobre la base para alinear el láser con el
borde de la superficie
6. Guía de trazado de 90° – calcule y gire ángulos en
incrementos de 5°
8 • S2/S2XL
E
SPANISH
OPERACIÓN
Ideal para uso en todo proyecto y trabajo de carpintería
incluyendo loza de porcelana, paneles, pared de yeso (drywall),
interruptores eléctricos
Usos horizontales
Coloque la unidad sobre una superficie
plana. Use el borde en T para poner la
unidad a escuadra con cualquier
superficie con una referencia de 90°
para alinear o colocar a plomo.
Usos verticales
Para fijarlo sobre una superficie vertical, aplíquele una
pequeña cantidad de masilla adhesiva a las almohadillas
(Fig. 3). Ponga en línea el instrumento usando las ampolletas de
nivelación. Oprima firmemente los botones para sujetar la
unidad a la superficie (Fig. 4).
S2/S2XL • 9
Fig. 3 Fig. 4
CALIBRACIÓN
Este instrumento fue calibrado en fábrica y nunca deberá
necesitar ser calibrado en el campo. La calibración deberá ser
efectuada únicamente por un centro de servicio autorizado.
Póngase en contacto con el Departamento de Servicio al
Cliente de CST/berger, una división de Stanley Works™ al
teléfono (815) 432-5237 en EE.UU.
PROCEDIMIENTOS DE OPERACIÓN
SEGUROS
Es posible trabajar seguramente con este instrumento
únicamente cuando la información de operación y seguridad
hayan sido leídas completamente y cuando las instrucciones
allí contenidas sean seguidas estrictamente.
No remueva la etiqueta ubicada a un lado de la carcasa.
El uso en combinación con otros instrumentos ópticos,
manipulaciones o uso en otro tipo de aplicaciones diferentes a
las descritas aquí podrán causar salidas de rayo láser peligrosas.
No mire directamente el rayo láser.
No apunte el rayo láser hacia otras personas.
CERTIFICACIONES
Este láser cumple con todas las porciones del título 21 del
Código de Regulaciones Federales que le aplican determinadas
por el departamento de Salud, Educación, Bienestar, la
Administración de Alimentos y Drogas, el Centro de
Dispositivos y la Agencia de Salud Radiológica.
El S2/S2XL también ha pasado las pruebas y cumple con los
requisitos para la obtención de la certificación CE publicados
en la Directiva 89/336/EEC y EN 61000-6-1 (EN50082-1), EN
61000-6-3 (EN50081-1) e IEC 60-825-1.
10 • S2/S2XL
Questo manuale è adatto per i seguenti modelli
1
Indice
Lingue:
Altri manuali Stanley Livello laser
Stanley
Stanley FatMax PB2 Manuale utente
Stanley
Stanley RL HW Manuale utente
Stanley
Stanley STHT77498-1 Manuale utente
Stanley
Stanley FatMax FMHT77598 Manuale utente
Stanley
Stanley FCL-G Manuale utente
Stanley
Stanley SP1X Manuale utente
Stanley
Stanley FatMax FMHT1-77413 Manuale utente
Stanley
Stanley SPL3 Manuale utente
Stanley
Stanley STHT77611 Manuale utente
Stanley
Stanley FatMax-CL2 Manuale utente
Stanley
Stanley CLLi Manuale utente
Stanley
Stanley STHT77502-1 Manuale utente
Stanley
Stanley IntelliLaser Pro Manuale utente
Stanley
Stanley STHT77616 Manuale utente
Stanley
Stanley STHT77149 Manuale utente
Stanley
Stanley STHT77504-1 Manuale utente
Stanley
Stanley Fatmax FMHT77617 Manuale utente
Stanley
Stanley SML Manuale utente
Stanley
Stanley SLP3 Guida all'installazione
Stanley
Stanley FATMAX FMHT1-77416 Manuale utente
