Stanley STDG5006 Manuale utente

STDG5006 English Page 3

ENGLISH

(Original instructions)

FIG. A

FIG. B FIG. C

FIG. D FIG. E

ENGLISH

(Original instructions)

DO NOT RETURN THIS PRODUCT TO THE STORE,

ﬁrst contact your local STANLEY Ofﬁce

or nearest authorized service center.

General Safety Rules

Warning! Read and understand all instructions.

Failure to follow all instructions listed below, may

result in electric shock, ﬁre and/or serious

personal injury.

SAVE THESE INSTRUCTIONS

Safety instructions

General power tool safety warnings

WARNING! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions listed below may result in electric shock, ﬁre

and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in all of the warnings listed below

refers to your mains operated (corded) power tool or battery

operated (cordless) power tool.

1. Work area safety

a. Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

b. Do not operate power tools in explosive

atmospheres, such as in the presence of ﬂammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

c. Keep children and bystanders away while operating

a power tool. Distractions can cause you to lose

control.

2. Electrical safety

a. Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools.

Unmodiﬁed plugs and matching outlets will reduce risk

of electric shock.

b. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

c. Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

d. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of

electric shock.

e. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric

shock.

f. If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electric shock. Note: The term “Residual Curent Device

(RCD)” can be replaced by “Ground Fault Circuit

Interrupter (GFCI)” or by “Earth Leakage Circuit Breaker

(ELCB)”.

3. Personal safety

a. Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not

use a power tool while you are tired or under the

inﬂuence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in

serious personal injury.

b. Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce personal

injuries.

c. Prevent unintentional starting. Ensure the switch is

in the off-position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your ﬁnger on the

switch or energising power tools that have the switch on

invites accidents.

d. Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal

injury.

e. Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool

in unexpected situations.

f. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

STDG5006

Voltage 220-240V

Frequency 50/60Hz

Power 500W

No-load speed 30000/min

Max chuck capacity 6mm

Max wheel diameter 25mm

Spindle M15

Speciﬁcations

g. If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-related hazards.

4. Power tool use and care

a. Do not force the power tool. Use the correct power

tool for your application. The correct power tool will do

the job better and safer at the rate for which it was

designed.

b. Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source and/or

the battery pack from the power tool before making

any adjustments, changing accessories, or storing

power tools. Such preventive safety measures reduce

the risk of starting the power tool accidentally.

d. Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained

users.

e. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tools

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations

different from those intended could result in a hazardous

situation.

5. Service

a. Have your power tool serviced by a qualiﬁed repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is

maintained.

Safety instructions for all operations Safety

warnings common for grinding'

a. This power tool is intended to function as a grinder

tool. Read all safety warnings, instructions,

illustrations and speciﬁcations provided with this

power tool. Failure to follow all instructions listed below

may result in electric shock, ﬁre and/ or serious injury.

b. Operations such as sanding, wire brushing,

polishing or cutting-off are not recommended to be

performed with this power tool. Operations for which

the power tool was not designed may create a hazard

and cause personal injury.

c. Do not use accessories which are not speciﬁcally

designed and recommended by the tool

manufacturer. Just because the accessory can be

attached to your power tool, it does not assure safe

operation.

d. The rated speed of the grinding accessories must

be at least equal to the maximumspeed marked on

the power tool. Grinding accessories running faster

than their rated speed can break and ﬂy apart.

e. The outside diameter and the thickness of your

accessory must be within the capacity rating of

your power tool. Incorrectly sized accessories cannot

be adequately controlled.

f. The arbour size of wheels, sanding drums or any

other accessory must properly ﬁt the spindle or

collet of the power tool. Accessories that do not match

the mounting hardware of the power tool will run out of

balance, vibrate excessively and may cause loss of

control.

g. Mandrel mounted wheels, sanding drums, cutters

or other accessories must be fully nserted into the

collet or chuck. If the mandrel is insufﬁciently held

and/or the overhang of the wheel is too long, the

mounted wheel may become loose and be ejected at

high velocity.

h. Do not use a damaged accessory. Before each use

inspect the accessory such as abrasive wheels for

chips and cracks, sanding drum for cracks, tear or

excess wear, wire brush for loose or cracked wires.

If power tool or accessory is dropped, inspect for

damage or install an undamaged accessory. After

inspecting and installing an accessory, position

yourself and bystanders away from the plane of the

rotating accessory and run the power tool at

maximum no-load speed for one minute. Damaged

accessories will normally break apart during this test

time.

ENGLISH (Original instructions)

i. Wear personal protective equipment Depending on

application, use face shield, safety goggles or

safety glasses. As appropriate, wear dust mask,

hearing protectors, gloves and workshop apron

capable of stopping small abrasive or workpiece

fragments. The eye protection must be capable of

stopping ﬂying debris generated by various operations.

The dust mask or respirator must be capable of ﬁltrating

particles generated by your operation. Prolonged

exposure to high intensity noise may cause hearing loss.

j. Keep bystanders a safe distance away from work

area. Anyone entering the work area must wear

personal protective equipment. Fragments of

workpiece or of a broken accessory may ﬂy away and

cause injury beyond immediate area of operation

k. Hold power tool by insulated gripping surfaces

only, when performing an operation where the

cutting accessory may contact hidden wiring or its

own cord. Cutting accessory contacting a “live” wire

may make exposed metal parts of the power tool “live”

and could give the operator an electric shock.

l. Always hold the tool ﬁrmly in your hand(s) during

the start-up. The reaction torque of the motor, as it

accelerates to full speed, can cause the tool to twist.

m. Use clamps to support workpiece whenever

practical. Never hold a small workpiece in one

hand and the tool in the other hand while in use.

Clamping a small workpiece allows you to use your

hand(s) to control the tool. Round material such as

dowel rods, pipes or tubing have a tendency to roll while

being cut, and may cause the bit to bind or jump toward

you.

n. Position the cord clear of the spinning accessory.

If you lose control, the cord may be cut or snagged and

your hand or arm may be pulled into the spinning

accessory.

o. Never lay the power tool down until the accessory

has come to a complete stop. The spinning

accessory may grab the surface and pull the power tool

out of your control.

p. After changing the bits or making any

adjustments, make sure the collet nut, chuck or

any other adjustment devices are securely

tightened. Loose adjustment devices can unexpectedly

shift, causing loss of control, loose rotating components

will be violently thrown.

q. Do not run the power tool while carrying it at your

side. Accidental contact with the spinning accessory

could snag your clothing, pulling the accessory into your

body.

r. Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the housing and

excessive accumulation of powdered metal may cause

electrical hazards.

s. Do not operate the power tool near ﬂammable

materials. Sparks could ignite these materials.

t. Do not use accessories that require liquid

coolants. Using water or other liquid coolants may result

in electrocution or shock.

Further Safety Instructions For All

Operations

Kickback And Related Warnings

Kickback is a sudden reaction to a pinched or snagged

rotating wheel, sanding band, brush or any other accessory.

Pinching or snagging causes rapid stalling of the rotating

accessory which in turn causes the uncontrolled power tool

to be forced in the direction opposite of the accessory’s

rotation.

For example, if an abrasive wheel is snagged or pinched by

the workpiece, the edge of the wheel that is entering into the

pinch point can dig into the surface of the material causing

the wheel to climb out or kick out. The wheel may either

jump toward or away from the operator, depending on

direction of the wheel’s movement at the point of pinching.

Abrasive wheels may also break under these conditions.

Kickback is the result of power tool misuse and/or incorrect

operating procedures or conditions and can be avoided by

taking proper precautions as given below:

a. Maintain a ﬁrm grip on the power tool and position

your body and arm to allow you to resist kickback

forces. The operator can control kickback forces, if

proper precautions are taken.

b. Use special care when working corners, sharp edges

etc. Avoid bouncing and snagging the accessory.

Corners, sharp edges or bouncing have a tendency to

snag the rotating accessory and cause loss of control or

kickback.

c. Do not attach a toothed saw blade. Such blades

create frequent kickback and loss of control.

ENGLISH

(Original instructions)

ENGLISH

d. Always feed the bit into the material in the same

direction as the cutting edge is exiting from the

material (which is the same direction as the chips

are thrown). Feeding the tool in the wrong direction

causes the cutting edge of the bit to climb out of the work

and pull the tool in the direction of this feed.

e. When using rotary ﬁles, cut-off wheels, highspeed

cutters or tungsten carbide cutters, always have the

work securely clamped. These wheels will grab if they

become slightly canted in the groove, and can kickback.

When a cut-off wheel grabs, the wheel itself usually

breaks. When a rotary ﬁle, highspeed cutter or tungsten

carbide cutter grabs, it may jump from the groove and

you could lose control of the tool.

Safety Warnings Speciﬁc For Grinding

Operations

a. Use only wheel types that are recommended for your

power tool and only for recommended applications.

For example: do not grind with the side of a cut-off

wheel. Abrasive cut-off wheels are intended for

peripheral grinding, side forces applied to these wheels

may cause them to shatter.

b. For threaded abrasive cones and plugs use only

undamaged wheel mandrels with an unrelieved

shoulder ﬂange that are of correct size and length.

Proper mandrels will reduce the possibility of breakage.

c. Do not “jam” a cut-off wheel or apply excessive

pressure. Do not attempt to make an excessive

depth of cut. Overstressing the wheel increases the

loading and susceptibility to twisting or snagging of the

wheel in the cut and the possibility of kickback or wheel

breakage.

d. Do not position your hand in line with and behind

the rotating wheel. When the wheel, at the point of

operation, is moving away from your hand, the possible

kickback may propel the spinning wheel and the power

tool directly at you.

e. When wheel pinched, snagged or when interrupting

a cut for any reason, switch off the power tool and

hold the power tool motionless until the wheel

comes to a complete stop. Never attempt to remove

the cut-off wheel from the cut while the wheel is in

motion otherwise kickback may occur. Investigate

and take corrective action to eliminate the cause of

wheel pinching or snagging.

f. Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed and

carefully reenter the cut. The wheel may bind, walk up

or kickback if the power tool is restarted in theworkpiece.

g. Support panels or any oversized workpiece to

minimize the risk of wheel pinching and kickback.

Large workpieces tend to sag under their own weight.

Supports must be placed under the workpiece near the

line of cut and near the edge of the workpiece on both

sides of the wheel.

h. Use extra caution when making a “pocket cut”into

existing walls or other blind areas. The protruding

wheel may cut gas or water pipes, electrical wiring or

objects that can cause kickback.

Storage and handing of recommended accessories.

7. Electrical safety

Your tool is double insulated; therefore no earth wire

is required. Always check that the main voltage

corresponds to the voltage on the rating plate.

Warning! If the power cord is damaged, it must be

replaced by the manufacturer, authorized STANLEY

Service Center or an equally qualiﬁed person in

order to avoid damage or injury. If the power cord is

replaced by an equally qualiﬁed person, but not authorized

by STANLEY, the warranty will not be valid.

(Original instructions)

Read

Instructions

Manual

Use Eye

Protection

Use Ear

Protection

V ........ Volts

A ........ Amperes

Hz ....... Hertz

W ........ Watts

min ..... minutes

..... Alternating

Current

..... Direct

Current

n0 ....... No-Load

Speed

...... Class II

Construction

.... Earthing

Terminal

.... Safety Alert

Symbol

.../min.. Revolutions

or Recipro-

cation per

minute

6. Labels on tool

The label on your tool may include the following symbols:

Position of date barcode

The Date Code, which also includes the year of

manufacture, is printed into the housing.

Example:

2014 XX JN

Year of manufacturing

ENGLISH

Features (Fig. A)

1. Collet chuck

2. Collet nut

3. Shaft cover

4. Ventilation slots

5. Cable

6. Toggle switch

7. Grinding Wheel

8. Spindle

9. Spanner

10. Front handle

11. Primary handle

Operating Instructions

1. Power supply

The power tool supply must match the nameplate data.

2. Installing wheel (Fig. B)

Warning! Only use grinding wheels with

maximum safe operating speed rated at or

above 40m/s. Ensure the grinding wheel is

correctly mounted and tightened, run the tool at no-load

speed for 30 secondes in safe position before using. Stop

immediately if there is considerable vibration or other

defects are detected. Never use damaged grinding wheels

or rimous ones.

a. Mount the spanner (9) to the spindle (8) and loosen the

clamping nut (2) with another spanner.

b. Insert the grinding wheel (7) shaft into the collet chuck

(1) as far as it can go.

c. Tighten the collet chuck (1) securely by spanners.

d. The maximum recommended diameter of mounted

wheel is 25mm.

e. The maximum recommended mandrel length of

mounted wheel is 24.5mm.

3. Switching on and off

Warning! Make sure you can control the switch

freely and keep it off before plugging in.

a. ON: Shift switch (6) to “I”. (Fig. E).

b. OFF: Shift switch (6) to “O”. (Fig E).

c. Let the wheel reach full speed before grinding.

d. Once the safety brush worn, grinder turns off

automatically to avoid motor damage. Motor was

damaged.

e. After inspecting and installing an accessory, run the

power tool at maximum no-load speed for ﬁve minutes

before any work.

Standard Attachments

1. Collet

2. Two Spanners (17mm)

Be sure to check the attachments as it is subject to change

by areas and models.

Application

Warning! To reduce the risk of injury, electric shock

and damage to the tool, before any work check the

utility lines electricity, gas or water supply line are

hidden in the work area.

Warning! Firmly grasp primary hold part of tool and

side handle before starting.

Grinding Application

a. Optimum grinding results are achieved when the

grinding tool is moved uniformly back and forth with light

pressure.

b. Pressure that is too strong reduces the performance

capability of the tool and cause the grinding to exhaust

more quickly.

c. Be sure that the distance between the top of collet chuck

and bottom of the grinding wheel is less than 8mm and

between the top of collet chuck and top of grinding wheel

is less than 45mm to prevent vibration of the tool and

unexpected accidents.(Fig. D)

Warning! Sparks generated when grinding

metal.Take care that no combustible material

presented on the area of ﬂying sparks.

(Original instructions)

ENGLISH

Protecting the environment

Separate collection. This product must not be

disposed of with normal household waste.

Should you ﬁnd one day that your Stanley product needs

replacement, or if it is of no further use to you, do not

dispose of it with household waste. Make this product

available for separate collection.

Separate collection of used products and packaging

allows materials to be recycled and used again.

Re-use of recycled materials helps prevent

environmental pollution and reduces the demand for raw

materials.

Local regulations may provide for separate collection of

electrical products from the household, at municipal waste

sites or by the retailer when you purchase a new product.

Stanley provides a facility for the collection and recycling of

Stanley products once they have reached the end of their

working life. To take advantage of this service please return

your product to any authorised repair agent who will collect

them on our behalf.

You can check the location of your nearest authorised repair

agent by contacting your local Stanley ofﬁce at the address

indicated in this manual. Alternatively, a list of authorised

Stanley repair agents and full details of our after-sales

service and contacts are available on the Internet at:

www.2helpU.com

(Original instructions)

Maintenance

Your tool has been designed to operate over a long period

of time with a minimum of maintenance. Continuous

satisfactory operation depends upon proper tool care and

regular cleaning.

Warning! Before performing any maintenance,

switch off and unplug the tool.

• Regularly clean the ventilation slots in your tool using a

soft brush or dry cloth.

• Regularly clean the motor housing using a damp cloth.

Do not use any abrasive or solvent-based cleaner.

Important! To assure product Safety and reliability,

repairs, maintenance and adjustment (other than

those listed in this manual) should be performed by

authorized service centers or other qualiﬁed service

personnel, always using identical replacement parts.

Lubrication

STANLEY tools are properly lubricated and are ready for

use.

Accessories

The performance of your tool depends on the accessory

used. STANLEY accessories are engineered to high quality

standards and designed to enhance the performance of

your tool. By using these accessories you will get the very

best from your tool.

Service Information

STANLEY offers a full network of company-owned and

authorized service locations. All STANLEY Service Centers

are staffed with trained personnel to provide customers with

efﬁcient and reliable power tool service. For more

information about our authorized service centers and if you

need technical advice, repair, or genuine factory

replacement parts, contact the STANLEY location nearest

you.

ENGLISH

One years full warranty

If your STANLEY product becomes defective due to faulty

materials or workmanship within 12 months from the date of

purchase, STANLEY guarantees to replace all defective

parts free of charge or – at our discretion – replace the unit

free of charge provided that:

• The product has not been misused and has been used in

accordance with the instruction manual.

• The product has been subject to fair wear and tear;

• Repairs have not been attempted by unauthorised

persons;

• Proof of purchase is produced.

• The STANLEY product is returned complete with all

original components

If you wish to make a claim, contact your seller or check the

location of your nearest authorised STANLEY repair agent in

the STANLEY catalogue or contact your local STANLEY

ofﬁce at the address indicated in this manual. A list of

authorised STANLEY repair agents and full details of our

after sales service is available on the internet

at:www.stanleytools.com

(Original instructions)

Indice

Altri manuali Stanley Stampante

Stanley

Stanley MODEL 1 Manuale utente

Manuali Stampante popolari di altre marche

Lexmark

Lexmark 1400 Series Manuale

Canon

Canon i70 Series Manuale utente

Evolis

Evolis Elypso Manuale utente

Kyocera

Kyocera FS-9530DN Manuale utente

Canon

Canon LASER SHOT LBP-1210 Manuale utente

Samsung

Samsung BIXOLON SRP-350plusF Manuale utente

Canon

Canon PIXMA PRO-1 Series Manuale utente

Canon

Canon PIXMA G3560 Guida all'installazione

Dell

Dell Color Laser Printer 2130cn Manuale utente

Tektronix

Tektronix Phaser 840 Manuale utente

Epson

Epson ET-7750 Istruzioni operative

Canon

Canon CLBR 460ps Manuale utente

Eltron

Eltron P210 Guide Manuale utente

Ricoh

Ricoh MD-P1 Manuale utente

Epson

Epson SC-F7100 series Manuale utente

Epson

Epson Stylus C40UX Manuale utente

Canon

Canon imagePASS-A2 Manuale utente

Canon

Canon S820D Manuale utente