Star Trac Spinner NXT 7090 Guida all'installazione
620-8006 Rev A
STAR TRAC
14410 Myford Road
Irvine, CA 926060 USA
COVER PAGE FOR DOCUMENT CONTROL PURPOSES ONLY, NOT TO BE PRINTED
Document:
Document Title: MANUAL, SP INSTALLATION, NXT
Document Number:620-8006 Rev: 001
Page Number: 1 of 16
Material:
n/a
Notes:
n/a
Approvals:
Originator
Print:
Deo Magakat
Sign: Date: 04/12/11
Approved By:
Sign: Date:
Document Revision History:
REV EFFECTIVE DATE BY DESCRIPTION ECO NO.
01 DMM DRAFT
A 14 June 2011 DMM RELEASE 13510
THE INFORMATION CONTAINED HEREIN IS PROPRIETARY AND CONFIDENTIAL TO UNISEN INC/STAR TRAC.
AND SHALL NOT BE USED OR DISCLOSED, IN WHOLE OR IN PART, WITHOUT FIRST OBTAINING THE WRIT-
TEN PERMISSION OF UNISEN, INC.
Print:
2
620-8006 Rev A
STAR TRAC
14410 Myford Road
Irvine, CA 926060 USA
SPINNER ASSEMBLY AND
INSTALLATION MANUAL
3
620-8006 Rev A
GENERAL
Before using this product, it is essential to read ALL installation Instructions and this
ENTIRE operations manual; the manual describes equipment setup and instructs
members on how to use it correctly and safely.
1. Open-End Wrench (Included)
2. Multi-purpose Wrench (Included)
3. 14mm Socket Wrench (Not Included)
4. 18mm Socket Wrench (Not Included)
5. 18mmHex Wrench (Not Included)
6. 21mm Open-end Wrench (Not Included)
7. Torque Wrench (Not Included)
8. Loctite 242 (Not Included)
9. Loctite 262 (Not Included)
TOOLS REQUIRED
If you are a Factory Certified Installer you must:
•
Adhere to all torque and assembly specifications.
•
Use a CALIBRATED TORQUE WRENCH with the necessary hex key sockets
•
NOT USE a powered drill, powered driver or powered impact tool for any part of the assembly.
•
Complete the assembly checklist on each Star Trac product.
•
Complete the final programming, functional and cosmetic checklists for each Star Trac product.
FACTORY CERTIFIED INSTALLER
Copyright 2011. Star Trac by Core Industries, Inc., Star Trac Fitness, Star Trac®, and the Star Trac Logo are registered trademarks of Core Ind, Inc.
All rights reserved, including those to reproduce this book or parts thereof in any form without first obtaining written permission from Star Trac.
Spin
®
, Spinner
®
, Spinning
®
and the Spinning logo are registered trademarks of Mad Dogg Athletics, Inc.
Smart Release™ is a registered trademark of Nautilus, Inc.
SPD is a registered trademark of Shimano American Corporation.
Every effort has been made to keep this information current; however, periodically, changes are made to the information herein, and these changes
will be incorporated into new editions of this publication. All product names and logos are trademarks of their respective owners.
4
620-8006 Rev A
Step 3.
Fold back all flaps at the top and at the bottom of
the box.
Step 4.
Slide-up the outer carton.
Step 2.
Open the carton first at the top and bottom. Use
scissors or a knife to cut the tape.
Caution: Be careful not to injure yourself; always
cut away from your body.
Step 1.
Arrange the assembly area so that the area is free
from objects that could potentially damage the
parts.
When positioning the box erify that the
HEAVY END logo is at the bottom as indicated by
the black o al in the picture.
UNPACKING INSTRUCTIONS
5
620-8006 Rev A
Step 8.
Position the main frame assembly upright and
remo e plastic protector.
Step 6.
Remo e the foam inserts from the shipment by
first taking out foam insert (1), then foam inserts
(2), and then last foam insert (3).
Step 5.
Arrange the unpacking area so that the area is
free from objects that could potentially damage
unpacked components.
Step 7.
Remo e components from foam inserts.
1
2 3
6
620-8006 Rev A
Step 9.
Place the main frame assembly on a flat surface
that is free from objects that could potentially
damage the unit.
Step 12.
Verify that the Spare Kit contains:
1. Pedal straps (2)
2. Spare brake pad (1)
Note: If the shipment is incomplete please con-
tact the Service Department at (800) 503-1221.
Step 10.
Verify that all shipment components are included:
1. Hardware, Pop-pin, and Pedals (set of two)
2. Handlebar w Grip and Water Bottle Holders (1)
3. Handlebar Post (1)
4. Seat Post (1)
5. Rear Leg Assembly (1)
6. Seat Slider Assembly w/Saddle (1)
7.
Front Leg Assembly w/Transport Wheels (1)
1
2
1
3
4 5
6 7
2
2 1
3 4
7
5
6
Step 11.
Verify the Hardware Kit contents:
1. M10 Flat Washer (4)
2. M10 Split Lock Washer (4)
3. M10X1.5, 25mm Hex Head Screw (4)
4. M8X1.25, 12mm Flange Hex Head Screw (2)
5. Open-End Wrench (1)
6. Multi-purpose Wrench (1)
7. Hex Wrenches (3)
7
620-8006 Rev A
Step 14.
Locate (2) M10 Hex Head screw. Pre-install an M10
Split Lock Washer and an M10 Flat Washer onto each
Hex head screw.
Note: Pay attention to the order of assembly of the
Split Loc Washer and Flat Washer.
Step 13.
Place the rear leg assembly in the mating position
under the frame.
Note: Ma e sure the thread posts in the frame
and the holes in the rear leg assembly are in
alignment.
ASSEMBLY INSTRUCTIONS
Step 15.
Secure the rear feet to the frame using (2) M10
Hex Head Screws with (2) M10 Split Lock Wash-
ers, and (2) M10 Flat Washer.
Torque screws to 35-40 lb-ft (47-54 Nm).
Note: Start threading screws by hand, then
tighten using an 18mm open-end or soc et
wrench.
Step 16.
Secure the front feet to the frame using (2) M10 Hex
Head Screws with (2) M10 Split Lock Washers, and
(2) M10 Flat Washer.
Torque screws to 35-40 lb-ft (47-54 Nm). Verify
that the front and rear feet are parallel to each
other.
Note: Start threading screws by hand, then tighten
using an 18mm open-end or soc et end wrench.
8
620-8006 Rev A
Step 20.
Locate the Pop-pin shown abo e.
Step 17.
Slide the Handlebar w/ Grip and Water Bottle
Holder onto the Handlebar Post.
Note: You may have to pull up on the Loc Knob
to help align the Slider Clamp with the guide rail.
Step 18.
Using a 2.5mm Hex Key, tighten the Button Head
Screw all the way down. This screw limits the
tra el of the Handlebar and pre ents the Handle-
bar from sliding off the Handlebar post acciden-
tally.
Note: Verify that no gap exists between the head
of the screw and the Handlebar slide rail.
Step 19.
Loosen the Pop-pin and pull it out away from the
Frame Handlebar Post.
Install and slide the Handlebar assembly into the
Frame Handlebar Post.
9
620-8006 Rev A
Step 23.
Align the slider clamp with the guide rail by turning
the Seat Slider Lock Knob.
Pull down on the locking pin and slide the seat rail
onto the seat post assembly.
Step 22.
With the Pop-pin loose pull and hold it away from
the frame seat post.
Install Seat Post into the Frame Seat Post.
2
1
Step 24.
Release the locking pin when the arrow points to a
alue between 0 and 7.
Step 21.
Install the Pop-pin into the Frame Seat Post using
a 21mm Open-end Wrench.
10
620-8006 Rev A
Step 25.
Locate the set of left and right pedals and follow
the orientation as shown in the picture abo e dur-
ing installation.
Step 28.
Secure the pedal tightly by using a 14mm Socket
wrench. Do not use an open end wrench to
tighten the pedal screws.
Torque screw to between 35-40 lbs-ft (47-54
Nm). Co er screw with Plastic End Cap.
Note: To prevent the pedal/cran arm from rotat-
ing, loc down the flywheel by turning the Bra e
Resistance nob cloc wise all the way down.
Step 26.
Locate one (1) M8x1.25 Flanged Hex Head
Screw, and (1) Plastic End Cap.
Note: Chec to ma e sure the screw has a blue
or red Loctite patch on the threads.
L R
Step 27.
Using a rubber mallet, firmly tap the left pedal
shaft into the left crank arm to seat and engage
the tapered shaft securely.
Start threading in the M8X1.25 Flanged Hex
Head screw by hand into the end of the pedal
shaft.
Note: Chec Cran Arm tapered hole and verify
that it is free of burrs or other debris. Verify that
the pedal tapered shaft is burr-free and clean.
Indice
Altri manuali Star Trac Cyclette
Star Trac
Star Trac 4-RB Manuale utente
Star Trac
Star Trac Pro Upright Bike Manuale utente
Star Trac
Star Trac Spinner ELITE 6900 Manuale
Star Trac
Star Trac Spinner NXT Black Belt Manuale
Star Trac
Star Trac Upright Sport Bike Manuale utente
Star Trac
Star Trac Spinner Velo XT Manuale utente
Star Trac
Star Trac E-UB Manuale utente
Star Trac
Star Trac eSPINNER Manuale utente
Star Trac
Star Trac SPINNER BLADE ION Istruzioni operative
Star Trac
Star Trac Spiner V Manuale utente
Star Trac
Star Trac Spinner Bike NXT 7000 Manuale utente
Star Trac
Star Trac Turbo Trainer Manuale utente
Star Trac
Star Trac 7270 Manuale utente
Star Trac
Star Trac Upright Pro bike Manuale utente
Star Trac
Star Trac 4-UB Manuale utente
Star Trac
Star Trac eSPINNER Manuale utente
Star Trac
Star Trac Spinner v Manuale utente
Star Trac
Star Trac S-UBx Manuale utente
Star Trac
Star Trac V-Bike Manuale utente
Star Trac
Star Trac Star Trac Fitness S-UBx Manuale utente
