Star TSP654II Series Manuale utente

THERMAL PRINTER

TSP650II SERIES

Hardware Manual

Federal Communications Commission

Radio Frequency Interference

Statement

is device complies with Part 15 of FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is

subject to the following two conditions:

(1) is device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.

L'exploitation est autorisée aux deux conditions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible

d'en compromettre le fonctionnement.

FCC CAUTION

Changes or modications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

For compliance with the Federal Noise Interference Standard, this equipment requires a shielded cable.

For RF interference suppression, if a ferrite core is provided with this device, ax it to the interface cable.

NOTE:

is equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part

15 of the FCC Rules. ese limits are designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. is equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

CAN ICES-3 (A) / NMB-3 (A)

is equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and

meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio

frequency (RF) Exposure rules. is equipment has very low levels of RF energy that it deemed to comply without

maximum permissive exposure evaluation(MPE). But it is desirable that it should be installed and operated keeping

the radiator at least 20cm or more away from person's body (excluding extremities: hands,wrists,feet and ankles).

Cet équipement est conforme aux limites d"exposition aux rayonnements énoncées pour un environnement non

contrôlé et respecte les règles les radioélectriques (RF) de la FCC lignes directrices d'exposition dans le Supplément

C à OET65 et d"exposition aux fréquences radioélectriques (RF) CNR-102 de l"IC. Cet équipement émet une

énergie RF très faible qui est considérée conforme sans évaluation de l"exposition maximale autorisée. Cependant,

cet équipement doit être installé et utilisé en gardant une distance de 20 cm ou plus entre le dispositif rayonnant et

le corps (à l"exception des extrémités : mains, poignets, pieds et chevilles).

國家通訊傳播委員會

國家通訊傳播委員會國家通訊傳播委員會

國家通訊傳播委員會(NCC)

(NCC)(NCC)

(NCC)警告

警告警告

警告

根據「低功率電波輻射性電機管理辦法」第十條

製造、輸入或販賣低功率射頻電機者，應於低功率射頻電機使用說明書內加

印第十二條及第十四條之規定內容。

「低功率電波輻射性電機管理辦法」第十二條

經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得

擅自變更頻率、加大功率或變更原設計之特性及功能。

「低功率電波輻射性電機管理辦法」第十四條

低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現

象時，應立即停用，並改善至無干擾時方得繼續使用。

前項合法通信，指依電信法規定作業之無線電通信。

低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備

之干擾。

Trademark acknowledgments

TSP650II : Star Micronics Co., Ltd.

Notice

permission is forbidden.

•e contents of this manual are subject to change without notice.

•All eorts have been made to ensure the accuracy of the contents of this manual at the time of going to press.

However, should any errors be detected, STAR would greatly appreciate being informed of them.

•e above notwithstanding, STAR can assume no responsibility for any errors in this manual.

•IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license.

•Android is a trademark of Google Inc.

•Windows is registered trademarks of Microso Corporation.

•Bluetooth® wordmark and logo are registered trademarks owned by Bluetooth SIG, Inc.

2013-2017 Star Micronics Co., Ltd..

Caution Symbol

ese symbols are located near the thermal print head.

Because the thermal print head is hot immediately aer printing, do not touch it. Static

electricity can damage the thermal print head. To protect the thermal print head from

static electricity, do not touch it.

is symbol is located near the cutter.

Never touch the cutter blade, as you could injure your ngers.

is symbol is located near the peripheral drive connector.

Do not connect this to a telephone.

is symbol is located near the screws securing the case or the protective plate, which

should not be opened by individuals other than service personnel. Individuals, other

than service personnel, should not remove these screws. High voltage areas in the case

can be dangerous.

TABLE OF CONTENTS

1. Unpacking and Installation......................................................................... 1

1-1. Unpacking .................................................................................................... 1

1-2. Notes about Installation ............................................................................... 1

2. Parts Identication and Nomenclature....................................................... 2

3. Setup ............................................................................................................ 3

3-1. Connecting the Interface Cable to the PC...................................................... 3

3-2. Connecting the Interface Cable to the Printer �� 4

3-3. Connecting the AC Adapter .......................................................................... 7

3-4. Turning the Power On................................................................................... 8

3-5. Connecting to a Peripheral Device ................................................................ 8

3-6. Loading a Paper Roll..................................................................................... 9

3-7. Bluetooth Settings (For Bluetooth Interface Models only)............................... 12

3-8. Setup Precautions ....................................................................................... 17

4. Attaching the Accessories........................................................................... 19

4-1. Attaching the Holder Plate.......................................................................... 19

4-2. Attaching the Rubber Feet .......................................................................... 21

4-3. Switch Cover Installation............................................................................ 21

5. Adjusting the Near-end Sensor .................................................................. 22

6. Error Indicators ......................................................................................... 23

6-1. Recoverable errors ...................................................................................... 23

6-2. Unrecoverable errors .................................................................................. 23

7. Preventing and Removing Paper Jams...................................................... 24

7-1. Preventing Paper Jams ................................................................................ 24

7-2. Removing Paper Jams ................................................................................. 24

7-3. Releasing the Cutter Lock ........................................................................... 25

8. Maintenance ............................................................................................... 26

8-1. Thermal Head............................................................................................. 26

8-2. Platen Rubber Roller .................................................................................. 26

8-3. Paper Holder .............................................................................................. 26

1. Unpacking and Installation

* Accessories vary depending on the model and the

region where the printer was purchased.

Paper roll

Printer

Holding plate

Screws

Switch blind

Safety Instruction

Setup sheet

Paper roll guide

Rubber feet

1-1. Unpacking

Aer unpacking the unit, check that all the necessary accessories are included in the package.

1-2. Notes about Installation

1. Choose a rm, level surface where the printer will not be exposed to vibration.

2. Make sure that the printer is connected to a reliable power outlet. It should not be on the same electric circuit as copi-

ers, refrigerators, or other appliances that cause power spikes.

3. e power outlet you plan to connect to for power should be nearby and unobstructed.

4. Make sure that the printer is not exposed to direct sunlight.

5. Make sure that the printer is well away from heaters and other sources of extreme heat.

6. Do not locate the printer in a badly ventilated or dusty environment.

7. Make sure that the room where you are using the printer is not too humid.

8. is device employs a DC motor and switches that have an electrical contact point.

Avoid using the device in environments where silicon gas can become volatile.

9. Use the printer within the boundaries indicated in the environmental requirements. Even when the ambient tem-

perature and humidity are within the specications, avoid radical changes in environmental conditions. e suitable

operating temperature range is as follows:

Operating temperature: 5°C to 45°C

10. When disposing of the printer, obey local regulations.

ERROR

FEED

POWER

TSP650

2. Parts Identication and Nomenclature

Control panel

Features lamps that indicate printer

status and a button for operating

the printer.

Printer cover

Open to replace paper.

Do not open while printing.

Power switch

Turnstheprinteron

and o.

Connects to peripheral devices

such as cash drawers.

Do not connect this to a tel-

ephone line.

Peripheral drive connector

Connects to an optional

AC adapter.

Power inlet

Connects to a host PC

through a cable.

Interface connector

Lights when the printer is online.

This lamp also indicates errors, in

combination with other lamps.

POWER lamp (green)

Lights when the cover is open.

This lamp also indicates errors, in

combination with other lamps.

ERROR lamp (red)

When the printer is online, pressing

this button feeds the paper roll.

FEED button

Cover open lever

Use this lever to open the

printer cover.

3. Setup

3-1. Connecting the Interface Cable to the PC

3-1-1. Parallel Cable

Connect the parallel cable to a parallel port on your PC.

3-1-2. RS-232C Cable

Connect the RS-232C cable to a RS-232C port on your PC.

3-1-3. USB Cable

Connect the USB cable to a USB port on your PC.

3-1-4. Ethernet Cable

Connect the Ethernet cable to a USB port on your PC.

Parallel interface cable

Ferrite core

Interface cable

5 cm

(maximum)

Fastener

Pull and cut

3-2. Connecting the Interface Cable to the Printer

Printer cables are not included in the package.

Obtain an appropriate cable that complies with the specications beforehand.

Because the appropriate interface cable diers depending on the system that you are connecting the printer to, contact

the dealer that you bought the product from if you are unsure about what cable to use.

Before connecting or disconnecting an interface cable, be sure to disconnect the AC adapter’s power cord from the outlet.

3-2-1. Parallel Interface Cable

To connect a parallel cable, follow the procedure given below.

(1) Make sure the printer is turn o.

(2) Ax the ferrite core onto the cable as shown in the illustration.

(3) Pass the fastener through the ferrite core.

(4) Loop the fastener around the cable and lock it. Use scissors to cut

o any excess.

(5) Connect the interface cable to the connector on the rear panel of

the printer.

(6) Fasten the connector clasps.

RS-232C interface cable

USB cable

Cable hook

4 cm (maximum)

3-2-2. RS-232C Interface Cable

(1) Make sure that the AC adapter’s power cord is not connected to the outlet.

(2) Connect the interface cable to the connector on the rear panel of the printer.

(3) Tighten the connector screws.

3-2-3. USB Cable

To connect a USB cable, follow the procedure given below.

(1) Make sure that the AC adapter’s power cord is not connected to the outlet.

(2) Connect the USB cable to the USB port.

(3) As shown in the gure, pass the cable through the cable hooks to hold it in place.

Indice

Altri manuali Star Stampante

Manuali Stampante popolari di altre marche

Lexmark

Lexmark 1400 Series Manuale

Canon

Canon i70 Series Manuale utente

Evolis

Evolis Elypso Manuale utente

Kyocera

Kyocera FS-9530DN Manuale utente

Canon

Canon LASER SHOT LBP-1210 Manuale utente

Samsung

Samsung BIXOLON SRP-350plusF Manuale utente

Canon

Canon PIXMA PRO-1 Series Manuale utente

Canon

Canon PIXMA G3560 Guida all'installazione

Dell

Dell Color Laser Printer 2130cn Manuale utente

Tektronix

Tektronix Phaser 840 Manuale utente

Epson

Epson ET-7750 Istruzioni operative

Canon

Canon CLBR 460ps Manuale utente

Eltron

Eltron P210 Guide Manuale utente

Ricoh

Ricoh MD-P1 Manuale utente

Epson

Epson SC-F7100 series Manuale utente

Epson

Epson Stylus C40UX Manuale utente

Canon

Canon imagePASS-A2 Manuale utente

Canon

Canon S820D Manuale utente