StarTech.com ST1214T Manuale utente

VGA over Cat5 UTP Extender

ST1214T

ST121R

ST121EXT

Instruction Manual

Actual product may vary from photo

VGA over Cat5 UTP Transmitter

VGA over Cat5 UTP Receiver

VGA over Cat5 UTP Extender

FFCCCCCCoommpplliiaanncceeSSttaatteemmeenntt

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

UUsseeooffTTrraaddeemmaarrkkss,,RReeggiisstteerreeddTTrraaddeemmaarrkkss,,aanndd

ootthheerrPPrrootteecctteeddNNaammeessaannddSSyymmbboollss

This manual may make reference to trademarks, registered trademarks, and other

protected names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only and

do not represent an endorsement of a product or service by StarTech.com, or an

endorsement of the product(s) to which this manual applies by the third-party company in

question. Regardless of any direct acknowledgement elsewhere in the body of this

document, StarTech.com hereby acknowledges that all trademarks, registered

trademarks, service marks, and other protected names and/or symbols contained in this

manual and related documents are the property of their respective holders.

TTaabblleeooffCCoonntteennttss

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

ST1214T (local) and ST121R (remote) . . . . . . . . . . . . . . . . . . . . . . . .2

ST1214T (local), ST121EXT (repeater) and ST121R (remote) . . . . . .3

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Equalizer selector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Instruction Manual

Thank for purchasing a StarTech.com Converge A/V VGA over Cat5 Video Extender.

Comprised of both the ST1214T (local unit), ST121R (remote unit), and optionally

ST121EXT (repeater), this video extender system allows you to split and extend a single

VGA source signal into up four separate signals, that can then be received by individual

receivers, for use with remotely located displays.

The VGA signal is extended from local to remote units using standard CAT 5 UTP cable,

with a maximum extension distance between local and remote units of up to 150m (500’)

or 300m (1000’)(with repeater)- providing a practical, cost effective way to extend your

VGA signal without any signal degradation or loss of pircture quality.

IInnttrroodduuccttiioonn

Features

BBeeffoorreeYYoouuBBeeggiinn

•Extends video cables by up to 500 ft. (150m)

•Pure hardware design, no software or drivers required

•Supports VGA, SVGA, and Multisync monitors

•Uses standard Category 5 straight-wired, twisted-pair, network patch cable for

economical and reliable data transmission

•Cat 5 cable - for connection(s) between transmitter unit, repeater and receiver

unit(s)

System Requirements

•VGA Signal source

•An available power outlet for each unit used

•Up to two VGA displays per receiver unit used

•1 X VGA Extender unit (ST1214T: local), (ST121R: remote) or (ST121EXT: repeater)

Package Contents

•1 X 9V AC 500ma Adapter

•1 x Instruction Manual

This package should contain:

Instruction Manual

IInnssttaallllaattiioonn

The following instructions detail how ST1214T, ST121R and ST121EXT can be used to

extend a VGA signal to remote displays, using a variety of different configurations.

ST1214T (local) and ST121R (remote)

1. a) Situate ST1214T so that it is near your VGA video source as well as an available

power source.

b) Connect ST1214T to the power source, using the power adapter provided.

c) Connect the VGA video source to the VGA IN port on ST1214T, using a standard

VGA cable.

2. a) Situate ST121R so that it is near the intended display(s) and an available power

source.

b) Connect the ST1214R to the power source using the power adapter provided.

c) Using the VGA OUT ports provided, connect ST121R to the displays. Please note

that each remote unit can be connected to two displays simultaneously; if you wish

to connect two monitors, simply repeat the VGA connection to an additonal display.

Using ST1214T, you can split the VGA signal from the source into 4 separate VGA

signals, for reception at remote locations (up to 150m / 500’ away).

3. Once the Local and Remote units have been positioned, connect the Cat5 OUT ports

provided by the local unit (ST1214T) to each remote unit, using standard UTP cable,

with RJ45 connectors on each end.

ST121R

ST1214T

VGA Cable

CAT5 Cable

< Up to 150m >

< Up to 150m >

Up to 150m

Power

connection

required

VGA Source

Instruction Manual

ST1214T (local), ST121EXT (extender) and ST121R (Remote)

Using ST1214T, you can split the VGA signal from the source into 4 separate VGA

signals, for reception at remote locations. While the maximum transmission distance of

ST1214T is 150m (500’), using ST121EXT as a signal repeater adds 100m / 328’ to the

total transmission distance, for a total extension of 250m/828’.

1. a) Situate ST1214T so that it is near your VGA video source as well as an available

power source.

b) Connect ST1214T to the power source, using the power adapter provided.

c) Connect the VGA video source to the VGA IN port on ST1214T, using a standard

VGA cable.

2. a) Situate the repeater unit (ST121EXT) up to 150m (500’) away from the ST1214T

unit, ensuring that the repeater unit is able to connect to an available power outlet.

b) Using a standard UTP cable with RJ45 terminators on each end, connect the Cat5

OUT port provided by the local unit(ST1214T) to the Cat5 IN port provided by

ST121EXT.

c) Connect the repeater unit (ST121EXT) to an available power outlet, using the

adapter provided.

Optionally, you can connect two monitors directly to the repeater. To do so, simply

connect the monitors to the VGA OUT ports (denoted by monitor symbols) provided by

the repeater unit.

3. Repeat

step 2

for each remote unit that will be used in conjunction with a repeater (up

to 4).

4. a) Situate the remote unit (ST121R) up to 150m (500’) away from the repeater

(ST121EXT) unit, so that it is near the intended display(s) as well as an available

power source.

b) Connect the ST121R Remote Unit to the power source using the power adapter

provided.

c) Using a standard UTP cable with RJ45 terminators on each end, connect the Cat5

OUT port provided by the repeater (ST121EXT) to the Cat5 IN port provided by

ST121EXT.

Please note that each remote unit can be connected to two displays simultaneously; if

you wish to connect two monitors, simply repeat the VGA connection to an additonal

display.

Please see page 4 for a detailed connectivity diagram.

Instruction Manual

Power

connection

required

VGA Cable

CAT5 Cable

< Up to 150m >

Up to 150m

Up to 100m

The following diagram illustrates the connection between local (ST1214T) and remote

(ST121R) units, with the addition of a repeater unit (ST121EXT). Please note that

although only one repeater is used in this illustration, up to four can be used

simultaneously.

< Up to 150m >

ST1214T

ST121EXT

ST121R

VGA Source

Instruction Manual

Operation

ST1214T, ST121EXT and ST121R all provide LED indicators, allowing simple operating

status monitoring. Once the power adapter has been connected, the Power LED will

become illuminated; similarly, when the unit is in use (i.e. transmitting a signal), the Active

LED will become illuminated.

Equalizer selector

ST121EXT and ST121R feature a signal equalizer that helps to optimize video signals

based on the attached cable length. Adjust this feature using the switch, located on the

front panel marked as Signal Equalizer, in accordance with the following distances:

CAT5 Cable Length Equalizer

Position

Meter Feet

0 - 40 0 - 131

40 - 80 131 - 262

80 - 120 262 - 394

120 - 160 394 - 525

Instruction Manual

VGA CAT5 Extender ST1214T ST121R ST121EXT

Maximum

transmission distance 150m (@1024 x 768) 150m (@1024 x 768) 70 - 100m

(@1024 x 768)

VGA Input Ports 1 x HDB15 (male) N/A N/A

VGA Output Ports 1 x HDB15 (female) 2 x HDB15 (female) 2 x HDB15 (female)

CAT5 Input Ports N/A 1 1

CAT5 Output Ports 4N/A 1

Operating voltage 9V DC, 600mA

Status Indicator Power (green) x 1

Active (yellow) x 1

SSppeecciiffiiccaattiioonnss

Instruction Manual

TTeecchhnniiccaallSSuuppppoorrtt

StarTech.com’s lifetime technical support is an integral part of our commitment to provide

industry-leading solutions. If you ever need help with your product, visit

www.startech.com/support and access our comprehensive selection of online tools,

documentation, and downloads.

WWaarrrraannttyyIInnffoorrmmaattiioonn

This product is backed by a one-year warranty. In addition, StarTech.com warrants its

products against defects in materials and workmanship for the periods noted, following

the initial date of purchase. During this period, the products may be returned for repair, or

replacement with equivalent products at our discretion. The warranty covers parts and

labor costs only. StarTech.com does not warrant its products from defects or damages

arising from misuse, abuse, alteration, or normal wear and tear.

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their

officers, directors, employees or agents) for any damages (whether direct or indirect,

special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business,

or any pecuniary loss, arising out of or related to the use of the product exceed the

actual price paid for the product. Some states do not allow the exclusion or limitation of

incidental or consequential damages. If such laws apply, the limitations or exclusions

contained in this statement may not apply to you.

Altri manuali per ST1214T

Questo manuale è adatto per i seguenti modelli

Altri manuali StarTech.com Estensione

StarTech.com

StarTech.com ST121R Manuale utente

StarTech.com

StarTech.com USB2G4LEXT2 Manuale utente

StarTech.com

StarTech.com HD202A Manuale utente

StarTech.com

StarTech.com STDHVHDBT Manuale utente

StarTech.com

StarTech.com SV565FXDUSA Manuale utente

StarTech.com

StarTech.com ST222HDBT Manuale utente

StarTech.com

StarTech.com EOC110K Manuale del sistema

StarTech.com

StarTech.com ST121HDBT20L Manuale utente

StarTech.com

StarTech.com ST12MHDLANU Manuale utente

StarTech.com

StarTech.com USB2G4LEXT2NA Manuale utente

StarTech.com

StarTech.com USB2004EXTGB Manuale utente

StarTech.com

StarTech.com ST121WHDST Manuale utente

StarTech.com

StarTech.com ST121 Series Manuale utente

StarTech.com

StarTech.com ST121UTPMINI Manuale utente

StarTech.com

StarTech.com STUTPRXWLA Manuale utente

StarTech.com

StarTech.com USBthere USB110EXT Manuale utente

StarTech.com

StarTech.com ST121UTP Manuale utente

StarTech.com

StarTech.com DPBOOST Manuale utente

StarTech.com

StarTech.com SV565UTPHDU Manuale utente

StarTech.com

StarTech.com 8STSV565HDIP Manuale utente

StarTech.com

StarTech.com 8STSV565DUTPU Manuale utente

StarTech.com

StarTech.com SV565UTPUL Manuale utente

StarTech.com

StarTech.com ST122UTPA Manuale utente

StarTech.com

StarTech.com USB2001EXT2P Manuale utente

Manuali Estensione popolari di altre marche

SY HDBT-60T Manuale utente

Appsys ProAudio

Appsys ProAudio ADX-16 Manuale utente

Atlona

Atlona RS232 Manuale utente

IDK

IDK OPF-TH1000-A Manuale utente

Enable-IT

Enable-IT 824WP Manuale utente

Worx

Worx Landroid RadioLink WA0864 Scheda tecnica

TP-Link

TP-Link TL-WA730RE Manuale utente

Camplex

Camplex CMX-HDMI-SFPL Manuale utente

SC&T

SC&T HE03-4K Manuale utente

Marmitek

Marmitek MegaView70 Manuale utente

Samsung

Samsung SCS-26UC4 Manuale utente

Foxun

Foxun SX-GES24 Manuale utente

MuxLab

MuxLab 500771 Manuale utente

foxunhd

foxunhd SX-AEX01 Manuale utente

TERK Technologies

TERK Technologies LFIRX2 Manuale utente

Devolo

Devolo Audio Extender Manuale

Edimax

Edimax EW-7438RPn V2 Manuale utente

Shinybow USA

Shinybow USA SB-6335T5 Manuale utente