StarTech.com ST12MHDLAN Manuale utente

Manual Revision: 03/15/2013

For the most up-to-date information, please visit: www.startech.com

DE: Bedienungsanleitung - de.startech.com

FR: Guide de l'utilisateur - fr.startech.com

ES: Guía del usuario - es.startech.com

IT: Guida per l'uso - it.startech.com

NL: Gebruiksaanwijzing - nl.startech.com

PT: Guia do usuário - pt.startech.com

ST12MHDLAN

HDMI® Audio/Video Over IP Extender Kit

*actual product may vary from photos

Instruction Manual

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there

is no guarantee that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be determined by

turning the equipment o and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other

protected names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only and do not

represent an endorsement of a product or service by StarTech.com, or an endorsement of the

product(s) to which this manual applies by the third-party company in question. Regardless

of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby

acknowledges that all trademarks, registered trademarks, service marks, and other protected

names and/or symbols contained in this manual and related documents are the property of

their respective holders.

Instruction Manual

Table of Contents

Introduction ............................................................................................1

Packaging Contents ................................................................................................................................. 1

System Requirements .............................................................................................................................. 1

Preparing Your Site ................................................................................................................................... 3

Hardware Installation Using Gigabit LAN Network ...................................................................... 4

Hardware Reset Procedure .................................................................................................................... 6

EDID Copy .................................................................................................................................................... 6

Factory Default Setting ........................................................................................................................... 6

Specications ..........................................................................................7

Technical Support ..................................................................................8

Warranty Information ............................................................................8

Instruction Manual

Introduction

The ST12MHDLAN HDMI® Over IP Extender kit lets you extend an HDMI® audio and

video signal over a Gigabit LAN network. The kit includes both the extender and

receiver for a complete all-in-one solution, and oers a highly scalable installation

when used with additional ST12MHDLANRX receiver units (sold separately). The

ST12MHDLANRX receivers can be connected to the same network to output the HDMI®

signal to over 100 additional displays.

This exible HDMI® extender can be connected through a Gigabit LAN portal and span

the entire distance of your network, or connected point-to-point with no network

hub for a small scale one-to-one extension of up to 330 feet (100 meters). Plus,

because the HDMI® signal is extended over standard Cat5e/Cat6 Ethernet cable with

RJ45 connectors, proprietary cables aren’t necessary, eliminating both the expense

and hassle of running specialized cables. For added versatility, up to 16 dierent

ST12MHDLAN Transmitter units can be added to a single network (IGMP Network

support required).

The HDMI® over IP Extender kit includes optional mounting hardware for a professional

and tidy installation.

Ideal for High-Denition applications, the extender supports 1080p video resolutions,

digital stereo audio, and features built-in EDID monitor emulation, which ensures

native resolution and maximum compatibility with your display or projector, for a

convenient plug-and-play installation.

Backed by a StarTech.com 2-year warranty and free lifetime technical support.

Packaging Contents

• 1 x HDMI® over IP Transmitter Unit

• 1 x HDMI® over IP Receiver Unit

• 2 x Mounting Bracket Kit

• 2 x Foot Pad Set

• 2 x Power Adapters

• 1 x Instruction Manual

System Requirements

• HDMI® enabled video source (i.e. computer, Blu-ray Player)

• HDMI® enabled display device(s) One for each Receiver (i.e. television, projector)

• Available AC electrical outlet for the Transmitter, and each Receiver

• HDMI® cable for each display

• Gigabit Networking devices and cabling

Instruction Manual

Transmitter Unit

Receiver Unit

1. F2 (Not Active)

2. F1 (Used during factory

default setting)

3. Dip Rotary Switch (Used to

pair Transmitter to Receiver)

1. F2 (Used during EDID Copy

procedure)

2. F1 (Used during factory

default setting)

3. Dip Rotary Switch (Used to

pair Transmitter to Receiver)

1. Power Jack

2. Network Status LED

3. Reset Button

4. LAN Port (RJ-45 Connector)

5. Video In

6. Link OK POWER LED

1. Power Jack

2. Network Status LED

3. Reset Button

4. LAN Port (RJ-45 Connector)

5. Video Out

6. Link OK POWER LED

NOTE: Serial 1 (Control) Ports, and Serial 2 (AUX/EXT) Ports are not active

(Additional Receiver units sold seperately ST12MHDLANRX)

Instruction Manual

Preparing Your Site

NOTE: The ST12MHDLAN HDMI® extender kit can use a Gigabit LAN Network to

extend the signal. Most Gigabit Network portals have a cable length restriction of

330 ft. (100m). Refer to the manufacturer of the equipment to determine the length

restriction and ensure the Transmitter Unit, and Receiver Unit(s) are all within the

restricted range of the nearest network portal.

Ensure the Transmitter Unit, and Receiver Unit(s) are all situated near an available AC

electrical outlet.

1. Determine where the local video source (i.e. computer, Blu-ray Player) will be

located and set up the device.

2. Determine where the remote display will be located and place/ mount the

display appropriately.

3. (Optional) If using additional receiver units (ST12MHDLANRX sold separately),

determine where the remote displays will be located in and place/ mount the

displays appropriately.

Instruction Manual

Hardware Installation Using Gigabit LAN Network

1. Install Transmitter Unit

a) Position the Transmitter Unit near the video source (i.e. Computer, Blu-ray Player).

b) Connect an HDMI cable from the video source device (i.e. computer, Blu-ray

Player) to the “Video In” port on the Transmitter Unit.

c) Connect the provided Transmitter Unit power supply.

2. Install Receiver Unit(s)

a) Position the Receiver Unit(s) near the video display (i.e. television, projector).

b) Connect an HDMI cable from the display Input to the “Video Out” port on the

Receiver Unit.

c) Connect the provided Receiver Unit power supply.

d) (optional) If using additional ST12MHDLANRX Receivers (sold separately), repeat

steps for each additional Receiver.

NOTE: The “Dip Rotary Switch” on the Extender and each Receiver connected to the

network must be set in the same position for the devices to communicate.

3. Connect the devices to a Gigabit LAN Network

a) Connect an RJ-45 terminated Cat5e/6 Ethernet cable to the “LAN Port” (RJ-45

Connector) on the Transmitter unit, and all receiver units.

NOTE: If you are using surface cabling, ensure you have enough Category 5e/6

unshielded twisted pair (UTP) network cabling to connect the Transmitter Unit to the

Gigabit LAN hub, router, or switch.

If you are using premises cabling, ensure that the Category 5e/6 unshielded twisted

pair (UTP) network cabling between the Transmitter and Gigabit LAN hub, router, or

switch has been properly terminated in a wall outlet in each location and there is a

patch cable long enough to connect the Network portal and Transmitter Unit to their

respective outlets.

b) Connect the other end of the Cat5e/6 cable run to a Gigabit LAN hub, router

or switch.

c) (optional) When adding additional Receiver Units (ST12MHDLANRX – Sold

separately), a run of Cat 5e/6 cable will be required from each device to the Gigabit

LAN hub, router or switch.

4. Your source video image will now appear on the Receiver unit(s) attached

video display.

Instruction Manual

(Optional) Point to Point Hardware Installation without Gigabit LAN Network

NOTE: While range is reduced to a maximum of 330 feet (100 Meters) the

ST12MHDLAN HDMI® extender kit also allows for extending the signal without a

Gigabit LAN Network by connecting the Transmitter directly to the Receiver using

CAT5e/6 cabling. This also eliminates the ability to add additional Receivers.

1. Install Transmitter Unit

d) Position the Transmitter Unit near the video source (i.e. Computer, Blu-ray Player).

e) Connect an HDMI® cable from the video source device (i.e. computer, Blu-ray

Player) to the “HDMI IN” on the Transmitter Unit.

f) Connect the provided Transmitter Unit power supply.

2. Install Receiver Unit(s)

e) Position the Receiver Unit(s) near the video display (i.e. television, projector).

f) Connect an HDMI® cable from the display Input to the “Video Out” port on the

Receiver Unit.

g) Connect the provided Receiver Unit power supply.

NOTE: The “Dip Rotary Switch” on the Extender and Receiver connected must be set in

the same position for the devices to communicate.

3. Install RJ-45 terminated Cat5e/6 Ethernet Cable

d) Connect an RJ-45 terminated Cat5e/6 Ethernet cable to the HDMI® Out Link

(RJ-45 Connector) on the Transmitter unit.

NOTE:

If you are using surface cabling, ensure you have enough Category 5e/6 unshielded

twisted pair (UTP) network cabling to connect the Transmitter Unit to the Receiver

Unit’s location, and that each end is terminated with a RJ45 connector.

If you are using premises cabling, ensure that the Category 5e/6 unshielded twisted

pair (UTP) network cabling between the Transmitter and Receiver Units have been

properly terminated in a wall outlet in each location and there is a patch cable long

enough to connect the Remote Unit and the Host Unit to their respective outlets.

e) Connect the other end of the Cat5/6 cable run to the RJ45 connector on the

remote Unit Receiver Unit.

4. Your source video image will now appear on the remote unit(s) attached

video display.

Instruction Manual

Hardware Reset Procedure

NOTE: If video signal does not appear on the display a hardware reset can be

performed on the Transmitter Unit, or individual Receiver Units.

1. Press the reset button on the device using a pin point tool, such as a ballpoint pen

or a bent paper clip.

EDID Copy

EDID allows the video source to output the most ideal signal to the video display. The

“EDID Copy” function on the ST12MHDLANRX ensures that EDID is still active through

the Ethernet extender.

NOTE: If you using multiple receivers the EDID can only be copied from one unit, the

signal customized for that display will be applied to all displays connected through

additional receivers.

1. Disconnect the power cable from the Receiver.

2. Hold down the F2 button

3. Reconnect the Power while holding down the F2 button

4. Release F2 button after the power has been reconnected for 12 seconds (the

Network Status LED ashes yellow), EDID is now active through the

Ethernet extender.

Factory Default Setting

1. Disconnect the power cable from the Transmitter/Receiver.

2. Hold down the F1 button

3. Reconnect the Power while holding down the F1 button

4. Release F1 button after the power has been reconnected for 17 seconds (the Link

OK POWER LED ashes green and blue)

5. Reconnect the Power again.

Instruction Manual

Specications

Maximum Digital Resolutions 1920x1200 @60Hz

Supported Resolutions 1920 x 1200 (1080p)

Wide Screen Supported Yes

Audio Specications Stereo Sound

Interface HDMI®

Cabling Cat 5e UTP or better

Audio Yes

Rack-Mountable Yes

Industry Standards HDMI®

HDCP

Daisy-Chain Yes

Transmitter Connectors 1x HDMI® (19 pin)

1x RJ-45

Receiver Connectors 1x HDMI® (19 pin)

1x RJ-45

Power Adapter Input Voltage 100~240V

Power Adapter Input Current 0.4 A

Power Adapter Output Voltage 5 DC V

Power Adapter Output Current 2 A

Center Tip Polarity Positive

Plug Type M

Altri manuali per ST12MHDLAN

Indice

Altri manuali StarTech.com Estensione

StarTech.com

StarTech.com SV565UTP Manuale utente

StarTech.com

StarTech.com ST1218T Manuale utente

StarTech.com

StarTech.com ST12MHDLAN4K Manuale utente

StarTech.com

StarTech.com SV565UTPDUA Manuale utente

StarTech.com

StarTech.com ST121HDFXA Manuale utente

StarTech.com

StarTech.com 110VDSLEXT Manuale utente

StarTech.com

StarTech.com IPUSB2VGA2 Manuale utente

StarTech.com

StarTech.com ST124UTPEA Manuale utente

StarTech.com

StarTech.com STDHVHDBT Manuale utente

StarTech.com

StarTech.com 33FT-8K-HDMI-BOOSTER Manuale utente

StarTech.com

StarTech.com ST121SHD50 Manuale utente

StarTech.com

StarTech.com USBthere USB204EXTFIB Manuale utente

StarTech.com

StarTech.com USB2G4LEXT2 Manuale utente

StarTech.com

StarTech.com ST121DVI25 Manuale utente

StarTech.com

StarTech.com ST121UTPHD2 Manuale utente

StarTech.com

StarTech.com ST121R Manuale utente

StarTech.com

StarTech.com USBthere USB204EXT Manuale utente

StarTech.com

StarTech.com ST121HDT4P Manuale utente

StarTech.com

StarTech.com 110VDSLEXTGB Manuale utente

StarTech.com

StarTech.com ST122UTPA Manuale utente

StarTech.com

StarTech.com ST121HDBTE Manuale utente

StarTech.com

StarTech.com ST12MHDLNHR Manuale utente

StarTech.com

StarTech.com SV565UTPUSA Manuale utente

StarTech.com

StarTech.com ST121HDBT20L Manuale utente

Manuali Estensione popolari di altre marche

SY HDBT-60T Manuale utente

Appsys ProAudio

Appsys ProAudio ADX-16 Manuale utente

Atlona

Atlona RS232 Manuale utente

IDK

IDK OPF-TH1000-A Manuale utente

Enable-IT

Enable-IT 824WP Manuale utente

Worx

Worx Landroid RadioLink WA0864 Scheda tecnica

TP-Link

TP-Link TL-WA730RE Manuale utente

Camplex

Camplex CMX-HDMI-SFPL Manuale utente

SC&T

SC&T HE03-4K Manuale utente

Marmitek

Marmitek MegaView70 Manuale utente

Samsung

Samsung SCS-26UC4 Manuale utente

Foxun

Foxun SX-GES24 Manuale utente

MuxLab

MuxLab 500771 Manuale utente

foxunhd

foxunhd SX-AEX01 Manuale utente

TERK Technologies

TERK Technologies LFIRX2 Manuale utente

Devolo

Devolo Audio Extender Manuale

Edimax

Edimax EW-7438RPn V2 Manuale utente

Shinybow USA

Shinybow USA SB-6335T5 Manuale utente