StarTech.com PCICOMBO Manuale utente
Installation Manual
PCICOMBO
Network Card
10 Mbps PCI Ethernet Card with Dual Interface
1
General Description
StarTech.com’s PCICOMBO PCI Network card comes with full support for duplex
modes and autoconfiguration through a workstation’s PCI BIOS, this PCI Card features
optional AUI connectors. Bus Mastered to greatly reduce system CPU load and sporting
a boot ROM socket for optional RPL boot ROM, this product is designed to provide
customers with an optional, dual interface for the Networking needs.
Features
• 32-bit PCI 2.0 Bus interface
• Plug and Play compatible with Windows 95, 98, ME, and Windows 2000
• Fully autoconfiguring through the computer's PCI BIOS
• Supports full duplex mode
• Low power consumption with sleep mode for energy saving PC's
• Optional AUI connector
• Bus Mastered to greatly reduce system CPU load
• Coax interface allows cable distances of up to 300m
• Boot ROM socket for optional RPL boot ROM
• Complies fully to IEEE 802.3 CSMA/CD Ethernet 10BaseT and 10Base2 Standards
• Two LED's indicate LINK and activity
• Drivers for all operating systems
Specifications
Standards IEEE 802.3 10BaseT, 10Base2, 10Base5
Data Transmission Rate
LEDs
Bus Type
IRQ
Boot ROM
Temperature
Dimensions
Certification
10Mbps or 20Mbps
UTP link status, Activity
PCI 2.0
Assigned by system
Assigned by system
Assigned by system
0 to 50 degrees C
140 x 63 mm
FCC part 15 class A, CE Mark
I/O Address
2
Getting Started
This section is designed to help you prepare the PCICOMBO card for installation. Please
read through this section carefully before attempting to install the card.
Unpacking the PCICOMBO card
This package should contain:
1 x PCICOMBO Network card
1 x BNCT connector
1 x driver disk
Installation
Network cards, like all computer equipment are subject to static electricity. Be sure that
you are properly grounded. StarTech.com recommends that you wear an anti-static strap
and that your system is unplugged before doing any work on the computer.
Card Installation
1. Turn off the computer and remove its cover.
2. Insert the card into a free PCI slot.
3. Connect to the network using AUI, thin or twisted-pair cable depending on the
connector you are using.
Card Configuration/ Diagnostic
Basically, the card is completely self-configurable, requiring no intervention from the
user. There are only 3 items that can be configured: Medium type, Full/Half duplex, and
Boot ROM enables. You can also run diagnostic of the card from the setup.exe program
provided with the PCICOMBO card.
Insert the disk provided, in DOS prompt, execute setup.exe command and you will see
the following:
• View Configuration
• Manual Setup Configuration
• Diagnostic
• Exit
Please follow the easy menu-driven program to configure the card.
Driver Installation
For detailed information, please refer to the document in the disk provided.
Examples:
1. For NetWare client, please execute the following:
lsl
pciodi
ipxodi
netx or vlm
f:
login username
2. For NetWare server, execute the following:
load pcisrv
bind ipx pxisrv
load monitor
Boot Rom Installation (Optional)
The PCICOMNO card provides a socket for a remote boot ROM. With a boot ROM, a
host computer can load the operating systems over the network.
1. Plug in the boot ROM to the appropriate position, make sure the direction is correct.
2. Enable the boot ROM function. Please see the Setup program for details.
AUI Bracket Installation (Optional)
You can buy another bracket containing an AUI connector from your dealer.
1. Hook up the cable to the connector pins market “AUI”. Make sure the red line on the
cable is positioned in the “pin 1” location.
2. Secure the bracket to the PC.
Troubleshooting
The most common factors that cause an adapter to fail are configuration conflicts and
cabling problems. PCI cards shouldn’t have any conflct problems due to Plug and Play
specifications. One should check the cable and its terminator. Also, use the adapter LED
indicators and diagnostic program. For information on the Diagnostic Program, please
see the Setup program. If the problem presists, call your dealer for help.
LED Indicators
The LEDs help you monitor the network status. Their functions depend on the type of
cable used.
*Link monitors the data link status on the UTP cable. It turns ON when there is data
linked, and OFF when there is a bad connection.
*Activity blinks when there is data transmission/reception.
3
Indice
Altri manuali StarTech.com Scheda PCI
StarTech.com
StarTech.com PCI2S650DVLP Manuale utente
StarTech.com
StarTech.com PEXUSB7LP Manuale utente
StarTech.com
StarTech.com PR22GI-NETWORK-CARD Manuale utente
StarTech.com
StarTech.com PCI1224PUSB Manuale utente
StarTech.com
StarTech.com PCIESATA2I Manuale utente
StarTech.com
StarTech.com PEX1S1P950 Manuale utente
StarTech.com
StarTech.com PCI1394 2LP Manuale
StarTech.com
StarTech.com PCI2S1P Manuale utente
StarTech.com
StarTech.com MPEX300WN2X2 Manuale del sistema
StarTech.com
StarTech.com PCI1S950DV Manuale utente
StarTech.com
StarTech.com PCI2S422ISO Manuale utente
StarTech.com
StarTech.com PEX1394A2V2 Manuale utente
StarTech.com
StarTech.com PEX1S1P952 Manuale utente
StarTech.com
StarTech.com PCIUSB3S2 Manuale utente
StarTech.com
StarTech.com PCISOUND5LP Manuale utente
StarTech.com
StarTech.com PCI1P2 Manuale utente
StarTech.com
StarTech.com PCI312PUSB/LP Manuale utente
StarTech.com
StarTech.com PCISAT2IDE1 Manuale utente
StarTech.com
StarTech.com PEX4S550 Manuale utente
StarTech.com
StarTech.com 8STPEX2S1P553B Manuale utente
