StarTech.com ARMPIVOTE Manuale utente
Manual Revision: 03/19/2018
For the most up-to-date information, please visit: www.startech.com
ARMPIVOTE
*actual product may vary from photos
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
Desk Mount Articulating Monitor Arm with Cable
Management and Gas Spring Height Adjust
Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Instruction Manual
i
Table of Contents
Introduction............................................................................................ii
Packaging Contents ................................................................................................................................. ii
Product Diagram ....................................................................................1
Installation ..............................................................................................2
Desk / Grommet Mounting ................................................................................................................... 2
Attaching the Display.............................................................................................................................. 4
Attaching the Gas Spring Arm Assembly ......................................................................................... 5
Cable Management.................................................................................................................................. 6
Adjusting the Gas Spring Arm Resistance........................................................................................ 7
Specications..........................................................................................9
Technical Support ..................................................................................10
Warranty Information............................................................................10
Instruction Manual
ii
Introduction
Packaging Contents
13
Plastic Gasket Cushion
Qty.2
Instruction Manual
1
Product Diagram
Instruction Manual
2
Installation
Desk / Grommet Mounting
The Monitor Arm can be clamped to a desk / table, or mounted through a grommet
hole. Instructions for both will be provided in the steps below.
1. Desk / Grommet Clamp: Remove the Left Cover and insert the L Plate portion of
the Clamp (4) into the base of the Pole (3) before replacing the Left Cover, then
apply the Plastic Gasket Cushions (13) as shown.
WARNING! It is the installer’s responsibility to ensure that the combined weight
of all components does not exceed the maximum 8 lb (3.6 kg) weight capacity of
the mounting arm.
Instruction Manual
3
2. Desk Clamp: Attach the bottom portion of the Clamp (4) to the L Plate, then place
the Clamp (4) opening around the edge of your desktop in your desired location
and tighten by hand to secure. Ensure that the Clamp is making full contact with
the desk surface.
Grommet Clamp: Place the L Plate through the grommet hole of your desk surface,
then attach the bottom portion of the Clamp (4) to the L Plate and tighten by hand to
secure. Ensure that the Clamp is making full contact with the desk surface.
3. Loosen the collar on the support post and adjust to the desired height.
Instruction Manual
4
Attaching the Display
1. Carefully place your display face down on a protective surface to access the
mounting points.
2. Depending on the depth of the mounting holes on your display, attach the display
to the Gas Spring Arm (1) using either the M4x12mm (11) screws, or the M4x25mm
(12) screws with spacers (10). Tighten using a Phillips screwdriver.
WARNING! Do not over-tighten the screws and stop immediately if you encounter
resistance to avoid damage to your display. Ensure that all spacers and screws being
used are the same length and thread type.
Instruction Manual
5
Attaching the Gas Spring Arm Assembly
1. Slide the Extension Arm (2) down onto the Pole (3).
2. Slide the Gas Spring Arm (1) onto the Extension Arm (2).
3. Place the Cover and Bolt (9) onto the Gas Spring Arm (1) and press the bolt down to
secure the two arms together.
Instruction Manual
6
Note: When attaching cables and routing through the cable management channels,
ensure that you leave enough slack to avoid stretching / pulling out the cables when
moving the arm.
1. Connect your cables to your display and position the mounting arm in its fully
extended position to ensure that the cables you are using are long enough to
allow for proper movement.
2. Feed the cables into the cable management channels on the underside of the
arms as shown.
3. Press the Cable Covers (8) into the slots as shown.
Cable Management
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali StarTech.com Rack e supporto
StarTech.com
StarTech.com ARMSTSCP1 Manuale utente
StarTech.com
StarTech.com WALLSTS1 Manuale utente
StarTech.com
StarTech.com SHELF-2U-14-CENTER-V Manuale utente
StarTech.com
StarTech.com 4POSTRACK12U Manuale utente
StarTech.com
StarTech.com RK12WALLOA Manuale utente
StarTech.com
StarTech.com ARMBARDUO Manuale utente
StarTech.com
StarTech.com ARMBARQUAD Manuale utente
StarTech.com
StarTech.com ARMWALLDSLP Manuale utente
StarTech.com
StarTech.com ARMSLIM Manuale utente
StarTech.com
StarTech.com STNDMTV100 Manuale utente
StarTech.com
StarTech.com RK4OD Manuale utente
StarTech.com
StarTech.com RK4242BK30 Manuale utente
StarTech.com
StarTech.com 8STARMSTSCP1 Manuale utente
StarTech.com
StarTech.com RK619WALL Manuale utente
StarTech.com
StarTech.com MONSTADQI Manuale utente
StarTech.com
StarTech.com ARMPIVOTB2 Manuale utente
StarTech.com
StarTech.com APLVESAMNTP Manuale utente
StarTech.com
StarTech.com WALLSTSI2 Manuale utente
StarTech.com
StarTech.com GNDBAR1U Manuale utente
StarTech.com
StarTech.com RKPNLTL2UV Manuale utente
