STILLA Conifer Manuale utente

STILLA

ASSEMBLY INSTRUCTIONS

‘Conifer’8x16

S3071

Every part needed to construct your shed is included inside the pack; cedar

panels, doors, windows, hardware kits & roof sheeting. Please ensure you fully

unpack all the parts & check against the parts checklist before contacting

customer service about anything you believe may be missing. Thank-you!

24/10/2023

1 | P a g e

Caution

Please be careful when handling all components, some parts have sharp metal edges.

Always wear work gloves, eye protection and long sleeves when assembling or maintaining

your shed.

Tools required for assembly

•Level

•Drill (capable of driving 100mm

Batten Screw)

•Hammer

•Ladder

•10mm Drill bit

•6mm Drill bit

•Tape measure

•Phillips head drive

•Hex Head Drive (5/16’)

•Safety glasses

•Gloves

•Circular/power saw (if heavy duty

floor was chosen)

•4mm Alan key

•Batten screw drive

Before assembly

•Before proceeding with installation, we recommend viewing the Cedar Studio video

at www.stilla.com.au/installation/ or search Stilla Cedar Studios on Youtube. This

doesn’t show the installation in detail however it could give you some handy tips.

Please note we haven’t videoed the assembly of each shed however the video online

is the Pioneer 20x10 and will give you an overall idea on how the installation process

is completed.

•Remove all parts from packages and place in a safe place close to assembly area.

•Review all instructions; continue to refer to instructions throughout assembly –step

by step.

Preparing your site

•If you are installing your shed on the Stilla heavy duty floor, this can be placed on

unlevelled surfaces and levelled up by using the 100x100 stumps provided.

24/10/2023

2 | P a g e

CONIFER 8x16 PARTS CHECKLIST

Part Code

Checked

Part Description

Qty

12P

Cedar Clad Ply Panel 1200x2020mm

Cedar Clad Ply Window Panel 1200x2020mm

SWA

Cedar Studio Window Assembly (add per additional WP)

Cedar Clad Ply Panel 900x2020mm

Cedar Clad Ply Panel 780x2020mm (Remove if DD)

SCD

Single Colonial Door 825x1885mm (remove if DD)

8ft Ply Gable (2 x LHS, 2 x RHS)

Cedar Clad Ply Front Panel 780x2020mm (DD option)

DCD

Double Colonial Door 710x1885mm (DD option)

FWP

Cedar Clad Ply Fixed Window Panel 1200x2020mm (option)

Corner Post 2015x65x18mm

Cover Strip 1890x40x7mm

Fixed Cover Strip 2015x40x7mm (4x per added fixed window)

8ft Studio Fascia Pack (4pcs) –140x20mm

Roof Rafter 1195x70x45mm

LCT

Large Collar Tie

SDH

Single Studio Door Head 840x123x45mm

SDSS

Single Door Surround Set –2@ 840mm, 2@ 1870mm (17x17)

DDH

Studio Double Door Head 1440x123x45mm

DDSS

Double Door Surround Set –2@ 1440mm, 2@ 1870mm (17x17)

DDS

Double Door Vertical Seal –1855x55x20mm

SIWS

Studio Internal Window Strip Set –2@ 770mm, 2@ 1240mm

(add per additional WP)

FGS

Front Gable Cover Strip –460mm

BGS

Back Gable Cover Strip –490mm

SCS

Stilla Cover Strip 2400x47x7mm (1@1800mm, 1@ 600mm)

1 & 1

Roof End Piece 203x70x30mm

RSB

Roof Support Block 250x70x45mm

1450mm Roof Sheet

Sky

1450 Skylight (option- swap with 1450 roof sheet)

1800mm Ridge Cap

1707mm Channel

8x16 Hardware Kit

8x16 Instruction Manual

REP

Roof End Plate 1568x70x45mm

MREP

Middle Roof End Plate 1571x70x45mm

Joining Plate 1145x70x45mm

RI (option)

Roof Insulation 4800x1300mm

24/10/2023

3 | P a g e

Floor Kit –Option

Floor Frame –140x35

Part Code

Checked

Part Description

Qty

Floor End Plate 1242x140x35mm

Floor Single Joist 1530x140x35mm

Floor Double Joist 1530x140x35mm

Floor Nog 379x42x35mm

Logs 750mm

1798mm x 800mm

598mm x 800mm

1798mm x 706mm

598mm x 706mm

Annex Kit –Option (add screws)

5120mm x 1450mm

Part Code

Checked

Part Description

Qty

VBJ

Veranda Beam Joiner 700x70x45mm

VOBJ

Veranda Outer Beam Joiner 700x140x35mm

Veranda Beam 2560x70x45mm

VOB

Veranda Outer Beam 2560x140x35mm

Veranda Rafter 1320x70x45mm

Veranda fascia 1350x140x20 block cedar

VRS

1450mm Veranda Roof Sheet

Veranda Posts 2400x90x90mm

Annex Deck Kit –Option (add screws)

4800mm x 1420mm

Part Code

Checked

Part Description

Qty

VEP

Veranda End Plate 4800x140x35mm

Veranda Joists 1350x140x35

VFB

Veranda Floorboards 4850x140x20mm

Veranda Logs 750x100x100mm

24/10/2023

4 | P a g e

If no floor option was purchased, go to step 2.0 (Wall Assembly)

SKIP TO BACK FOR IMAGES TO HELP WITH FLOOR INSTALL

STEP 1.0

FLOOR KIT

1.0 –FLOOR KIT (1 of 6 floor frames)

PART CODE

QTY

DESCRIPTION

Floor End Plate 1242mm

Floor Single Joist 1530mm

Double Joist 1530mm

100BS

100mm Batten screw

1.0 –FLOOR FRAME (1 of 6 floor frames)

Fasten floor frame together as indicated in diagram below, using lines and predrilled

holes. Screw through EP into DJ using 3x 100BS.

Screw through EP into SJ using 2 x 100BS per join.

Ensure frame is square by measuring from corner to corner diagonally, frame will be

square when both diagonal measurements equal the same.

REPEAT THIS PROCESS FOR FASTENING 5 MORE FLOOR FRAMES.

ENSURE 42x35 side of the DJ sits at top.

FRONT

24/10/2023

5 | P a g e

STEP 1.1

FLOOR FRAME INSTALLATION

The 8x16 floor frame comes in six parts. Install first floor frame in desired position at desired

height and fasten to logs once level and square, then join and fasten next frame until all six

are joined and secured to logs.

1.1 –FLOOR FRAME INSTALLATION

PART CODE

QTY

DESCRIPTION

Logs 750x100x100mm

100BS

100mm batten screws

65BS

65mm Batten Screws

200PB

200mm M12 Post Bolt

M12 Washers

1.1 –FLOOR FRAME INSTALLATION

Repeat the steps below for each floor frame, joining the floor frames together as you go

in order displayed in diagram below.

1. Lay out frame in desired position and mark holes to dig, as indicated on diagram

below (use shovel or marking paint).

2. Dig and place logs in holes (using concrete if you wish).

3. Fasten floor frame to logs at desired height, using 4x 100BS per log, ensuring

frame is level*.

4. Butt next floor frame into last installed frame and join using 6x 65BS evenly spaced

along EP or SJ.

5. Repeat process until all frames are joined.

* Fasten frame to logs when roughly level and then critique by hammering in or adding

dirt (or concrete) to corners until perfectly level at every post.

Once all frames are joined, predrill holes (using a 13mm drill bit) and bolt each log to the

floor frame in spots indicated with 200PB, using washers on both sides.

FRONT

24/10/2023

6 | P a g e

STEP 1.2

FLOOR NOG INSTALLATION

1.2 –FLOOR NOG INSTALLATION

PART CODE

QTY

DESCRIPTION

Floor Nog 379x42x35mm

65HHS

65mm Hex Head Screws

1.2 –FLOOR NOG INSTALLATION

Mark out measurements shown below (centre of nog). Fasten Floor Nogs (FN) in positions

shown in diagram below using 1x 65HHS per join.

24/10/2023

7 | P a g e

STEP 1.3

FLOOR INSTALLATION

1.3 –FLOORING INSTALLATION

PART CODE

QTY

DESCRIPTION

Floor Board 1798x800mm

Floor Board 598x800mm

Floor Board 1798x706mm

Floor Board 598x706mm

50PS

150

50mm Philips Screw

1.3 –FLOORING INSTALLATION

Fasten floor sheets to floor frame as shown in diagram below using 50PS.

Bring Floor sheets in 47mm on two EP sides from the outside of the floor frame and 44mm

from the two DJ sides as seen below.

Note- The x marked on the floor sheets do not line up with our joists.

FRONT

24/10/2023

8 | P a g e

STEP 2.0

SINGLE DOOR WALL PANEL LAYOUT

The 8x16 Conifer comes standard with a single door in the gable end of the shed with two

front panels either side, as seen in the plan below. Follow the steps outlined in the

following pages to assemble this plan in the correct order.

Note: Any additional window panels purchased can be positioned and replace any of the

1200 panels (12P) seen on this plan.

DOUBLE DOOR WALL PANEL LAYOUT (OPTION)

The double door option includes double doors in the gable end of the shed with two front

panels either side, as seen in the plan below.

24/10/2023

9 | P a g e

STEP 2.1

WALL ASSEMBLY

2.1 - ASSEMBLY PARTS –WALL ASSEMBLY

PART CODE

QTY

DESCRIPTION

780mm Front Panel (replace with 480 FP if DD)

480mm Front Panel (ONLY IF DOUBLE DOOR OPTION PURCHASED)

900mm Panel

65HHS

65mm Hex head screw

2.1 - ASSEMBLY –WALL ASSEMBLY

Screw through FP into 9P (top, centre & bottom) using 3 x 65HHS*. Cedar strip on FP should be

on the door side.

* It helps to have one person adjusting from the outside and one person screwing on the inside.

Note: Ensure tongue on cedar cladding is at top.

IMPORTANT CORNER DETAIL:

Install frame flush on the outside of plywood

bracing.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali STILLA Casa da giardino

STILLA

STILLA S3031 Manuale utente

STILLA

STILLA Willow S3061 Manuale utente

STILLA

STILLA Hyland S3015 Manuale utente

STILLA

STILLA Windsor S3008 Manuale utente

STILLA

STILLA Willow 12x8 Manuale utente

STILLA

STILLA Chatswood Manuale utente

STILLA

STILLA S3071 Manuale utente

STILLA

STILLA Hazel 9x6 Manuale utente

STILLA

STILLA EASTWOOD 8x12 Manuale utente

STILLA

STILLA S3011 Manuale utente

STILLA

STILLA Hyland Manuale utente

STILLA

STILLA Bromley Manuale utente

STILLA

STILLA Hollydean S3094 Manuale utente

STILLA

STILLA Oxford Manuale utente

STILLA

STILLA S3071 Manuale utente

STILLA

STILLA S3031 Manuale utente

STILLA

STILLA Wattle 8x4 Manuale utente

STILLA

STILLA Windsor S3008 Manuale utente

STILLA

STILLA Hyland S3015 Manuale utente

STILLA

STILLA Richmond 6x4 Manuale utente

STILLA

STILLA S3110 Manuale utente

STILLA

STILLA S3021 Manuale utente

STILLA

STILLA Hideout S2011 Manuale utente

STILLA

STILLA Hampton Manuale utente

Manuali Casa da giardino popolari di altre marche

Mercia Garden Products

Mercia Garden Products 0628LOG181-V4 Manuale utente

Lemeks

Lemeks Palmako PA120-5930-6 Manuale dell'installatore

Gartenhaus-King

Gartenhaus-King Valery Manuale utente

Rion

Rion Hobby Gardener Manuale utente

POD

POD Camping 480 Manuale utente

Select

Select ISAAC E9682 Manuale utente

Mercia Garden Products

Mercia Garden Products 01DTSHPWOR1010DDOW-V4 Manuale di istruzioni

Palmako

Palmako Saale Manuale utente

Lemeks

Lemeks Palmako Kira EL16-3623 Manuale dell'installatore

Mercia Garden Products

Mercia Garden Products 0644LOG186-V4 Manuale di istruzioni

Palmako

Palmako Roger FR44-5953-2 Manuale utente

Mercia Garden Products

Mercia Garden Products 03DTSHHP1206HGD4MW-V1 Manuale di istruzioni

WAR-LOCK

WAR-LOCK GARDENSHED Skillion Series Manuale utente

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Manuale utente

G21

G21 Boston 882 Manuale utente

Lemeks

Lemeks Palmako Grace PM56-4529 Manuale dell'installatore

Mercia Garden Products

Mercia Garden Products 03WES0808-V1 Manuale di istruzioni

Shire

Shire Salcey Manuale utente