STREAMCORE SG 850e Manuale utente

Streamcore.com Page 1 on 16

IG_SG850E-SG1600E-SG3200E_EN-R0

Streamcore.com Page 2 on 16

Table des matières

1Introduction .......................................................................................................................................3

1.1 Elements delivered ...................................................................................................................................3

1.2 Steps to follow..........................................................................................................................................3

2Description.........................................................................................................................................4

2.1 SG 850e/1600e .........................................................................................................................................4

2.2 SG 3200e ..................................................................................................................................................5

3Configuring boot IP parameters .........................................................................................................6

3.1 Overview ..................................................................................................................................................6

3.2 Configure StreamGroomer boot IP parameters with asynchronous cable..................................................6

3.2.1 Asynchronous port settings and login ........................................................................................................................ 6

3.2.2 Maintenance Menu (default)...................................................................................................................................... 7

3.2.3 Configuration Menu.................................................................................................................................................... 9

3.3 Configure StreamGroomer boot IP parameters with a USB key...............................................................10

3.3.1 Prepare the boot file in StreamView ........................................................................................................................ 11

3.3.2 Download the boot file on the local host ................................................................................................................. 11

3.3.3 Insert USB key into StreamGroomer and reboot...................................................................................................... 11

4Wiring / Start ...................................................................................................................................12

4.1 SG850e / 1600e connectivity .................................................................................................................. 12

4.2 Connectivity in any architecture .............................................................................................................12

5Checking the connectivity of the SG..................................................................................................14

5.1 Using StreamView ..................................................................................................................................14

5.2 Using ping...............................................................................................................................................14

6Appendix..........................................................................................................................................15

6.1 Technical Specifications ..........................................................................................................................15

6.2 Manually load a Boot version ................................................................................................................. 15

6.3 Description of the cables ........................................................................................................................ 16

6.3.1 Asynchronous cable .................................................................................................................................................. 16

6.3.2 Straight Ethernet cable ............................................................................................................................................. 16

6.3.3 Crossover Ethernet cable.......................................................................................................................................... 16

Streamcore.com Page 3 on 16

1Introduction

1.1 ELEMENTS DELIVERED

The set should contain:

•A wiring data sheet:

•A power cord:

•An asynchronous cable:

•A gray straight-through cable (x2 for 4 Ports):

•A red crossover cable (x2 for 4 Ports):

•A StreamGroomer 850e / 1600e / 3200e:

1.2 STEPS TO FOLLOW

This documentation describes how to install and start a StreamGroomer 850e, 1600e and 3200e. The following

steps should be carried out:

1. Configure the boot IP parameters with the asynchronous interface or USB key and reboot (chapter 3)

The following IP parameters must be provided:

Line mode of administration port (speed, duplex)

StreamGroomer administration IP address *

Mask associated with StreamGroomer IP address*

SGM IP address (2 IP addresses in case of a backup)*

Gateway to the SGM**

DNS server***

DNS suffix***

* Required

** Required if the SGM is not on the same subnetwork as the StreamGroomer

*** Required for the caching feature and used for manual requests from the boot menu (ping…)

2. Connect the cables and start the StreamGroomer (chapter 4)

3. Check the connectivity (chapter 5)

Streamcore.com Page 4 on 16

2Description

2.1 SG 850E/1600E

2.1.1.1 FRONT PANEL

1. – Admin. interface LED

2. – On/Off switch

2.1.1.2 REAR PANEL

Power supply

LED indicator for speed &

bypass

Asynchronous port

WAN1 / LAN1 port

Administration port

WAN2 / LAN2 port (for 4

Ports)

The LED has two possible usages:

•Normal usage consists of speed and activity. It indicates if the interface works at 10/100 Mbps or 1000 Mbps.

•If the two LED 100 AND 1000 are on, the Bypass is "closed": traffic goes directly from one port to the other

without being processed by the SG. The SG acts as a crossover cable.

Streamcore.com Page 5 on 16

2.2 SG 3200E

2.2.1.1 FRONT PANEL

Admin. interface LED

EXT port

On/Off switch

LED indicator for speed &

bypass

Asynchronous port

WAN1 / LAN1 port

Administration port

WAN2 / LAN2 port (for 4

Ports)

The LED has two possible usages:

•Normal usage consists of speed and activity. It indicates if the interface works at 10/100 Mbps or 1000 Mbps.

•If the two LED 100 AND 1000 are on, the Bypass is "closed": traffic goes directly from one port to the other

without being processed by the SG. The SG acts as a crossover cable.

2.2.1.2 REAR PANEL

Power supply 1

10.

Power supply 2

Streamcore.com Page 6 on 16

3Configuring boot IP parameters

3.1 OVERVIEW

There are two methods to configure the boot IP parameters of a SG:

- with the asynchronous cable (console port): access to the boot menu of the SG

- with a USB key: reboot the SG on a USB key containing a configuration file prepared with the StreamView

application.

Boot menu is the same for the whole e-series (SG250e/350e/850e/1600e/3200e).

3.2 CONFIGURE STREAMGROOMER BOOT IP PARAMETERS WITH ASYNCHRONOUS CABLE

3.2.1 Asynchronous port settings and login

To access the BOOT menu, you have to connect to the StreamGroomer through the asynchronous port via a DB9

asynchronous cable. The most well known utilities are HyperTerminal, PuTTY or Teraterm for Windows. The

configuration has to be done manually by entering the asynchronous port settings as follows:

Speed 38400 bit/s, no parity, no flow control, 1 stop bit, 8 bits of data.

Press Enter key. The following screen appears:

Initial login

Enter user name (login): boot

and a password: boot.

Streamcore.com Page 7 on 16

Once entered in the boot menu, there are two levels: Maintenance menu (default) and Configuration menu

To access the configuration menu, type the keyword "configure". You can exit any menu with the "exit" command.

All commands can be completed with the tab key.

You also have access to the boot menu by telnet, RSH or SSH to the SG from the SGM. (same login)

Only one person can be connected on the boot menu at a time.

3.2.2 Maintenance Menu (default)

Available Commands

Description

configure

Enters configuration mode

exit

Leaves the current mode. If changes are pending, a confirmation is requested

ping [IP_Add]

Sends ICMP ECHO_REQUEST to a network host – specify an IP address

reset_configuration All the operational software and configurations are therefore deleted, the name

of the StreamGroomer and the parameters of the interface providing access to the

SGM are set on the default value attributed at the factory. This option requires

certain precautions.

restart [A/B/S] Restarts the SG in the chosen version (OPE A, B or System)

show […]

Displays various information about the SG and the admin network

traceroute [IP_Add] Traces path to a network host – specify an IP address

help

Lists the available command

Show Commands detail Description

show arp

Lists the entries of the ARP table

show changes

Presents the changes between the current configuration and the pending changes

show conf

Presents the current configuration

show date

Shows the system date and the last time update (every day at midnight)

show interface Gives the active status of the interface with its IP Address, MAC Address, MTU and

transmitted volume

show iprouting

Presents the admin routing table of the SG

show version Presents the type of the SG, its serial number, the installed and activated version of

the SG

Streamcore.com Page 8 on 16

Examples:

[SG850e > maintenance] show arp

IP address HW address

----------------------------------

10.0.0.1 00.0d.dd.cd.33.03

10.0.0.120 00.03.2d.15.fa.20

10.0.0.130 00.03.2d.0d.04.28

[SG850e > maintenance] show iprouting

Destination Netmask Gateway Metric Use

0.0.0.0 255.255.255.255 0.0.0.0 1 0

10.0.0.0 255.255.0.0 0.0.0.0 0 3

0.0.0.0 0.0.0.0 10.0.0.1 1 14175

[SG850e > maintenance] show version

Running OS : BOOT S15-1e2252a392b5

SG flash type : M4G64

SG type : SG850e

Serial number : R64T8426

Installed versions

Partition S : S15-1e2252a392b5

Partition A : 6.0.04-056fb620c05a

Partition B : None

Streamcore.com Page 9 on 16

3.2.3 Configuration Menu

Configuration diagram

*: Configuration available in boot mode (unless security settings)

**: - If the « try » is confirm, pending configuration are saved (like an « apply »)

- If the « try » is cancel, active configuration is rebuilt from the Configuration file; pending configurations are still available

Available Commands

Description

apply

Save and apply pending changes

exit

Leave the current mode

help

List the available commands

show […]

Display various information about the SG and the admin network

try Apply pending changes without saving them.

If the « try » is confirmed, pending configuration are saved (like an « apply »)

If the « try » is cancelled, active configuration is rebuilt from the Configuration file;

pending configurations are still available

undo […] Delete pending changes. You can specify a parameter to cancel.

If no parameter is given, all changes will be cancelled.

Show Commands detail

Description

show arp

List the entries of the ARP table

show changes

Present the changes between the current configuration and the pending changes

show conf

Present the current configuration

show date

Show the system date and the last time update (every day at midnight)

show interface Give the active status of the interface with its IP Address, MAC Address, MTU and

transmitted volume

show iprouting

Present the routing table of the SG

show version Present the type of the SG, its serial number, the installed and activated version of

the SG

Streamcore.com Page 10 on 16

Configuration Commands

Description

admin_address [IP_Add]*

Define the IP address at which the StreamGroomer is accessible

admin_mask [Mask]*

Define the IP network through which the admin of the SreamGroomer should pass

admin_gateway [IP_Add]*

Identify the IP address of the gateway allowing you to contact the SGM from the SG

admin_port_speed [speed]*

Choose the speed of the interface [100M-fd/100M-hd/10M-fd/10M-hd/1G-fd/auto]

boot_pwd

Allow you to change the “boot” login password

dns_server1 [IP_Add]

DNS server used by the SG (for admin purpose). It is needed for the web caching

dns_server2 [IP_Add]

Second DNS server used by the SG in case the first one does not answer.

dns_suffix1 [domain_name]

DNS suffix for local DNS query

dns_suffix2 [domain_name]

Second DNS suffix for local DNS query

name [xxx]

Name presented as prompt

public_key_sgm […]*

Public key of the SGM used for the secured connection between SGM and SG

secure_com [yes/no]

Activate/Deactivate secured communication between SGM and SG (SSH)

sgm_address [IP_Add]

IP address of the SGM server which administers the SG

sgm_address2 [IP_Add]

IP address of the first backup SGM server which administers the SG (option)

sgm_address3 [IP_Add]

IP address of the second backup SGM server which administers the SG (option)

sgm_address4 [IP_Add]

IP address of the third backup SGM server which administers the SG (option)

ssh_port*

TCP port to use with the secured communication between SG and SGM (22 by default)

To remove a configuration value, use the “no” command following with the command name.

Ex: ‘no sgm_address3’

3.3 CONFIGURE STREAMGROOMER BOOT IP PARAMETERS WITH A USB KEY

The StreamGroomer boot IP parameters can also be automatically imported through a USB key containing a boot

configuration file. Follow these steps (to enable RSH communications between the SGM and SG):

1. Prepare the boot file in Streamview

2. Download the boot file on the local host

3. Transfer the boot file on an USB key (by email, FTP... or directly from the local host)

4. Plug the USB key on the SG

5. Reboot the SG

*: SG IP configuration and security configuration are only available in boot mode

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente