Summit Appliance FF61BI Manuale utente

Write Model and Serial Numbers here:

Model _________________________

Serial No. ______________________

BUILT-IN AUTO-DEFROST ALL-REFRIGERATORS

Models:

M405 CM411L

Instruction Manual

BEFORE USE, PLEASE READ AND FOLLOW

ALL SAFETY RULES AND OPERATING INSTRUCTIONS

FELIX STORCH, INC.

770 Garrison Avenue

Bronx, NY10474

www.summitappliance.com

CFF61BI FF63BBI

IMPORTANT SAFEGUARDS

Your safety and the safety of others are very important.

Before the refrigerator is used, it must be properly positioned and

installed as described in this manual, so read the manual carefully. To

reduce the risk of fire, electrical shock or injury when using the

appliance, follow basic precautions, including the following:

•Plug into a grounded 3-prong outlet. Do not remove grounding prong, do not use an

adapter, and do not use an extension cord.

•It is recommended that a separate circuit, serving only your refrigerator, be provided. Use

receptacles that cannot be turned off by a switch or pull chain.

•Never clean appliance parts with flammable fluids. These fumes can create a fire hazard

or explosion. And do not store or use gasoline or other flammable vapors and liquids in the

vicinity of this or any other appliance. The fumes can create a fire hazard or explosion.

•Before proceeding with cleaning and maintenance operations, make sure the power line of

the unit is disconnected.

•Do not connect or disconnect the electric plug when your hands are wet.

•Unplug the appliance or disconnect the power before cleaning or servicing. Failure to do

so can result in electrical shock or death.

•Do not attempt to repair or replace any part of your refrigerator unless it is specifically

recommended in this material. All other servicing should be referred to a qualified

technician.

•Use two or more people to move and install the refrigerator. Failure to do so can result in

back or other injury.

•To ensure proper ventilation for your appliance, the front of the unit must be completely

unobstructed. Choose a well-ventilated area with temperatures above 60°F (16°C) and

below 90°F (32°C). This unit must be installed in an area protected from the elements,

such as wind, rain, water spray or drips.

•The appliance should not be located next to ovens, radiators or other sources of high heat.

•The appliance must be installed with all electrical connections in accordance with state

and local codes. A standard electrical supply (115V AC only, 60 Hz), properly grounded in

accordance with the National Electrical Code and local codes and ordinances, is required.

•Do not kink or pinch the power supply cord of the appliance.

•The fuse (or circuit breaker) size should be 15 amperes.

•It is important for the refrigerator to be leveled in order to work properly. You may need to

make several adjustments to level it.

•Never allow children to operate, play with or crawl inside the refrigerator.

•Do not use solvent-based cleaning agents or abrasives on the interior. These cleaners

may damage or discolor the interior.

•Do not use this apparatus for other than its intended purpose.

Risk of child entrapment!

Child entrapment and suffocation are not problems of the past. Junked or abandoned

refrigerators and freezers are still dangerous, even if they will “just sit in the garage a few

days.”

•Before you throw away your old refrigerator or freezer:Take off the doors.

Leave the shelves or drawers in place so that children may not easily climb inside.

•Never allow children to operate, play with, or crawl inside the appliance.

THIS APPLIANCE IS NOT INTENDED FOR USE BY YOUNG CHILDREN OR INFIRM PERSONS

UNLESS THEY HAVE BEEN ADEQUATELY SUPERVISED BY A RESPONSIBLE PERSON TO

ENSURE THAT THEY CAN USE THE APPLIANCE SAFELY. YOUNG CHILDREN SHOULD BE

SUPERVISED TO ENSURE THAT THEY DO NOT PLAY WITH THE APPLIANCE.

- SAVE THESE INSTRUCTIONS -

To save energy and maintain optimum performance:

Your refrigerator may be installed as a free-standing unit or built into an

enclosure or below a countertop.

When positioning this unit: If used freestanding allow at least 2 inches of

clearance on top, at the sides and in the rear for sufficient airflow. If unit is built

in, allow 2” of air space between the rear of the unit and the wall and leave at

least 1/8” on both sides and 1/16” at the top. Be sure that airflow under the

appliance is not blocked.

Table of Contents

Important Safeguards ....................................................................................................1 - 2

Location of Parts .................................................................................................................3

Technical Information .........................................................................................................4

Installation Instructions .................................................................................................5 - 7

Before Using Your Appliance ..........................................................................................5

Installing the Refrigerator ................................................................................................5

Electrical Connection / Extension Cord............................................................................6

Reversing the Door Swing / Switching the Door Handle .................................................7

Operating Your Refrigerator ...............................................................................................8

Temperature Control

Defrosting Your Appliance

Care and Maintenance ........................................................................................................9

Cleaning Your Appliance / Power Failure / Vacation Time/

Moving your Appliance / Energy-Saving Tips

Troubleshooting.................................................................................................................10

Limited Warranty ...............................................................................................................11

Location of Parts

Temperature control dial

(thermostat) and interior

light

Door with storage

compartments

Front ventilation

slots (kick plate)

Leveling legs

Adjustable glass

shelves

Defrost water

outlet

(behind crisper)

Handle

Crisper and

glass cover

Wine rack

Technical Information

Model Numbers

FF61BI (white)

FF63BBI (black exterior)

Capacity 5.5 cu. ft.

Electrical Input 115V AC/60Hz

Rated Current 0.902A

Refrigerant R134a (1.7 oz.)

Unit Weight 86 lbs.

Installation Built-in or free-standing

Unit Dimensions (W x D x H) 23.63" x 23.5" x 33.5"

NOTE: Specifications are subject to change without notice.

Installation Instructions

Before Using Your Appliance:

•Remove the exterior and interior packing.

•Before connecting the unit to a power source, let it stand for approximately 2

hours. This will reduce the possibility of a malfunction in the cooling system from

handling during transportation.

•Remove the shelves and clean them and the interior surfaces of the unit with

lukewarm water using a soft cloth.

Installing the Refrigerator:

•Place the unit on a floor that is strong enough to support it when the appliance is

fully loaded. To level the unit, adjust the two leveling legs at the front.

•Your appliance can be installed either free-standing, recessed or built into an

enclosure. When installing as a free-standing unit, allow at least 2” (51mm) of

space at the sides, top and rear of the unit to allow for proper air circulation to cool

the compressor and condenser. Even when built in, the unit requires at least 2” of

clearance at the back, 1/8” (3mm) at both sides and 1/16” (1.6mm) at the top.

Take care that the air vents at the front of the appliance are never covered or

blocked in any way.

•This appliance is supplied with spacers that have to be mounted onto the

condenser tube at the back to make sure there is sufficient clearance between the

appliance and the wall.

•Locate the unit away from direct sunlight and sources of heat (oven, heater,

radiator, etc.). Direct sunlight may affect the acrylic coating and heat sources may

increase electrical consumption. Extremely cold ambient temperatures may also

affect the unit's performance.

•Avoid locating the unit in moist areas. Too much moisture in the air will cause frost

to form quickly on the evaporator, requiring more frequent defrosting of the

interior.

•Plug the unit into an exclusive, properly installed and grounded wall outlet. Any

questions concerning power and/or grounding should be directed toward a

certified electrician or authorized service center.

Improper use of the grounded plug can result in the risk of electrical shock. If the power

cord is damaged, have it replaced by the manufacturer, its service agent or similarly

qualified persons in order to avoid a hazard.

Electrical Connection:

This unit should be properly grounded for your safety. The power cord of this unit is

equipped with a three-prong plug which mates with a standard three-prong wall outlet

to minimize the possibility of electrical shock.

Do not under any circumstances cut or remove the third ground prong from the

power cord supplied. For personal safety, this appliance must be properly grounded.

This unit requires a standard 115-volt AC/60Hz electrical outlet with three-prong

ground. Have the wall outlet and circuit checked by a qualified electrician to make

sure the outlet is properly grounded. When a standard 2-prong wall outlet is

encountered, it is your responsibility and obligation to have it replaced with a

grounded 3-prong wall outlet.

To prevent accidental injury, the cord should be secured behind the unit and not left

exposed or dangling.

The unit should always be plugged into its own individual electrical outlet which has a

voltage rating that matches the rating label on the appliance. This provides the best

performance and also prevents overloading house wiring circuits that could cause a

fire hazard from overheated wires. Never unplug the unit by pulling on the power

cord. Always grip the plug firmly and pull straight out from the receptacle. Repair or

replace immediately any power cord that has become frayed or otherwise damaged.

Do not use a cord that shows cracks or abrasion damage along its length or at either

end. When moving the unit, be careful not to damage the power cord.

Extension Cord:

Do not use an extension cord with this appliance. If the power cord is too short, have

a qualified electrician or service technician install an outlet near the appliance.

Reversing the Door Swing (not available on models ending CSS, SSHV, or SSTB:

If you find the direction of opening the door of the appliance inconvenient, you can

change it. Holes on the opposite side have already been prepared at the factory.

This appliance can be opened from either the right side or the left. By default, the

door hinge is on the right side. If you prefer it on the left, please follow these

instructions:

1. Take off upper hinge cover from the door and remove the screws that hold top

hinge.

2. Lift the hinge straight up to free the hinge pin from the socket in the top of the

door.

3. Lift the door up and away to free its bottom socket from the hinge pin.

4. Remove the screws to the bottom hinge.

5. Remove the decorative caps from the opposite side and plug the holes from the

original side with the decorative caps.

6. Move the bottom hinge to the opposite side and tighten the screws. Use any lock

washers or nuts if they were used in the original installation.

7. Replace door onto the hinge pin on the bottom hinge. Place top hinge pin into

door. Insert screws into the top hinge and tighten.

Switching the Door Handle:

The door has two screw holes on each side, allowing you to move the handle from one

side to the other. To do so, unscrew the handle from its original location and align the

handle with the screw holes on the opposite side. Fix the handle in place with the

screws, then cover the screw heads with the handle seal.

1 Upper hinge cover

2 Upper hinge

3 Lower hinge

4 Kick plate

5 Handle

6 Fastener at corner with hole

Operating Your Refrigerator

Temperature Control:

•Your appliance’s evaporator system is out of sight behind the interior rear wall.

•The interior temperature is controlled with a thermostat knob

located inside the unit, towards the upper right-hand corner.

Turn the knob clockwise from the STOP (0) position toward

the higher numbers for colder temperatures. Higher settings

on the knob (higher numbers) mean lower temperatures

(colder) in the refrigerator.

•On the coldest settings, temperatures in some spots inside

the cabinet may drop below 32°F. Use higher thermostat settings only when

required or recommended. When the ambient temperature is normal, we

recommend a medium setting.

•Changes in the ambient temperature affect the temperature inside the refrigerator

so choose an appropriate setting of the thermostat knob, depending on ambient

conditions.

•In the STOP (0) position, the appliance does not operate (the cooling system is

switched off), yet the power supply is not interrupted (the light still works).

•The temperature inside the refrigerator also depends on how often you open the

door.

•In all small refrigerators without interior fans, temperatures are coldest near the

bottom, and occasionally near the rear. Place contents accordingly. It is best not

to operate these units mostly empty. If temperatures are erratic, try putting some

water bottles inside to create a load for the compressor.

NOTES:

1. The glass shelves are adjustable. These shelves stop short an inch before the

back wall, which is essential for air flow and the proper operation of the automatic

defrost system. Do not block these gaps.

2. Interior lighting is controlled by a switch that is activated by the opening and

closing of the refrigerator door.

3. If the refrigerator is unplugged, has lost power or is turned off, you must wait 3 to

5 minutes before restarting it. If you attempt to restart before this time delay, the

unit will not start.

Defrosting Your Appliance:

This appliance operates with an automatic defrost system, so the refrigerator defrosts

itself. While the compressor is operating, ice will build up along the cold rear wall (the

evaporator plate is behind the wall). During the compressor’s off-cycle, ice will melt,

drip down, collect in the trough at the bottom and drain through a small hole into a

tray above the compressor; where the compressor’s heat will evaporate the water. If

you notice excessive ice build-up on the rear wall, try adjusting the thermostat to a

slightly warmer setting. Be sure that the door gasket is sealing well and that there is

no obstruction of the drain hole at the bottom rear of the interior cabinet.

Care and Maintenance

Cleaning Your Appliance:

1. Unplug the appliance, turn the thermostat to STOP (0) and remove all contents,

including shelves and crisper.

2. Wash the inside surfaces with a solution of lukewarm water and vinegar.Wipe

dry with a clean, soft cloth.

3. Wash the shelves and crisper with a mild detergent solution, then rinse and dry

thoroughly.

4. Wash the outside cabinet with a solution of warm water and mild liquid detergent.

Rinse well and wipe dry with a clean soft cloth.

5. Wring excess water out of the sponge or cloth before cleaning the area of the

temperature control or any electrical parts.

6. From time to time, wipe the condenser on the back wall with a soft

non-metallic brush or vacuum cleaner.

7. After you have cleaned the appliance, reconnect it to the power

supply, reset the thermostat and return all contents to their place.

CAUTION: Failure to unplug the unit before cleaning or maintenance

could result in electrical shock or personal injury.

Power Failure:

Most power failures are corrected within a few hours and should not affect the

temperature of your appliance if you minimize the number of times the door is

opened. If the power is going to be off for a longer period of time, you need to take

the proper steps to protect your chilled items.

Vacation Time:

During long absences, remove all contents. Unplug the appliance, clean it and leave the

door open slightly to avoid possible formation of condensation, mold or odors.

Moving Your Appliance:

1. Remove the contents.

2. Securely tape down all shelving inside the unit.

3. Turn the leveling legs up to the base to avoid damage.

4. Tape the door shut.

5. Be sure the appliance stays secure in the upright position during transportation.

Energy-Saving Tips:

•The unit should be located in the coolest area of the room, away from heat-

producing appliances or heating ducts and out of direct sunlight.

•Try not to open the door too often, especially when the weather is damp and hot.

Once you open the door, close it as soon as possible.

•Occasionally check if the appliance is sufficiently ventilated (adequate air

circulation behind and at the front of the appliance).

•Set the thermostat from higher to lower settings as soon as possible (depending

on how loaded the appliance is, ambient temperature, etc.).

•Before loading items into the unit, be sure they have cooled to ambient

temperature.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Summit Appliance Frigorifero

Summit Appliance

Summit Appliance accucold PLUS Series Manuale utente

Summit Appliance

Summit Appliance Accucold CM411L Manuale utente

Summit Appliance

Summit Appliance FF61W Manuale utente

Summit Appliance

Summit Appliance AccuCold FCL44 MED Series Manuale utente

Summit Appliance

Summit Appliance FF7BK Series Manuale utente

Summit Appliance

Summit Appliance FF1DSS Manuale utente

Summit Appliance

Summit Appliance Accucold ACR612 Manuale utente

Summit Appliance

Summit Appliance CT661W Series Manuale utente

Summit Appliance

Summit Appliance SPRF34D Manuale utente

Summit Appliance

Summit Appliance accucold FFAR121SS Manuale utente

Summit Appliance

Summit Appliance Accucold FFAR10 Manuale utente

Summit Appliance

Summit Appliance Accucold FFAR24LMAN Manuale utente

Summit Appliance

Summit Appliance Accucold CP133 Manuale utente

Summit Appliance

Summit Appliance Accucold CT66 Series Manuale utente

Summit Appliance

Summit Appliance BRF65S2 Manuale utente

Summit Appliance

Summit Appliance CT661BI Manuale utente

Summit Appliance

Summit Appliance CFF61WBI Manuale utente

Summit Appliance

Summit Appliance Accucold ACR1717 Series Manuale utente

Summit Appliance

Summit Appliance accucold FF6 Series Manuale utente

Summit Appliance

Summit Appliance accucold ACR1718 Series Manuale utente

Summit Appliance

Summit Appliance accucold FFAR12W Manuale utente

Summit Appliance

Summit Appliance BeautiFridge Manuale utente

Summit Appliance

Summit Appliance BRF65S Manuale utente

Manuali Frigorifero popolari di altre marche

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Manuale utente

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Manuale utente

Sharp

Sharp SJ-BA31IEXW2-EU Manuale utente

CORBERO

CORBERO CC2300MCW Manuale utente

KitchenAid

KitchenAid 2205264 Manuale utente

Stengel

Stengel KU 1101 A++ Manuale utente

NEFF

NEFF KI181 Series Manuale utente

Hoshizaki

Hoshizaki Reach-In Manuale utente

Amana

Amana ASD2524VES00 Manuale utente

BOMANN

BOMANN KGC 213 Manuale utente

Danby

Danby DAR044A1SLDD Istruzioni per il montaggio

Samsung

Samsung RF323TE Manuale utente

Beko

Beko CSA31022 Manuale utente

IKEA

IKEA FROSTIG C 185 E Manuale utente

Electrolux

Electrolux ER 6821 D Manuale utente

True

True TS-28 Manuale utente

Frigidaire

Frigidaire FSC23R5DW9 Manuale utente

Beko

Beko LSP4579W Manuale utente