Sunstream SWIFTSHIELD A Series Manuale utente
FORM NO. 660843 REV. B PAGE 1
READ CAREFULLY BEFORE ASSEMBLY AND USE.
KEEP THESE INSTRUCTIONS.
COPYRIGHT 2017 SUNSTREAM CORPORATION® - ALL RIGHTS RESERVED
A-SERIES
ASSEMBLY, INSTALLATION AND USE MANUAL
PILING LIFT
For: Most
Four Post
Piling Lifts
SS-AMP12124B
SS-AMP14136B
FORM NO. 660843 REV. B PAGE 2
TABLE OF CONTENTS
DISCLAIMER OF LIABILITY
These assembly and installation instructions have been provided by SunStream Corporation® at the
request of the potential installer and/or assembler. If you are not an authorized SunStream® Dealer and
are not a reasonably-skilled mechanic, please contact SunStream® so that we can refer you to a local
dealer who can skillfully and safely perform the assembly and installation of your SunStream® boatlift. It is
the potential installer and/or assembler’s responsibility to determine whether he or she has the necessary
skills, knowledge, and tools to properly and safely assemble and/or install the SunStream® lift described
herein. Improper assembly and/or installation may cause the lift to function improperly or not to function.
Improper assembly and/or installation may additionally cause a risk to personal safety or property.
If the assembler and/or installer is confused or has questions or concerns about a particular assembly
or installation, he or she should contact SunStream® by telephone at (253) 395-0500 before proceeding
further. The information contained in these instructions does not constitute a warranty or guarantee
of any kind.
An assembler’s and/or installer’s failure to correctly follow these assembly and installation instructions
constitutes a waiver of the assembler and/or installer’s rights against SunStream® regarding any
Subsequent damages to property or personal injury caused by the assembler’s and/or installer’s improper
Safety Instructions………………………………………………………3
Overview………………………………………………………………..4-5
Tools Required…………………………………………………………..6
Installation and Assembly
Bow Sprit………………………………………………………….7-10
Frame……………………………………………………………..11-29
Power Pack………………………………………………………….23
Installing and Adjusting the Cover………………………….30-36
Removing the cover……………………………………………38-40
Custom Trimming Roller and crossbeam………………….41-42
Quick Tips……………………………………………………………….43
Maintenance ……………………………………………………………44
Troubleshooting………………………………………………………..45
Accessories……………………………………………………………..46
Warranty……………………………………………………………. 47-48
FORM NO. 660843 REV. B PAGE 3
IMPORTANT SAFETY INSTRUCTIONS
If you have any questions, please call your dealer, or SunStream® at (253)395-0500
Save These Instructions
Your safety and the safety of others is very important. Proper use of the information in
this manual will help avoid potential hazards that could cause damage to property
and/or personal injury. It is not possible, however, to identify and warn users of
all hazards associated with the assembly, installation, operation, and maintenance of
the SwiftShield A-SeriesTM. You must use your own good judgment.
SAFETY WARNINGS
Failure to comply with the following rules may result in severe injury and/or death
and damage to property. Misuse of your lift may cause the lift and boat to become
unstable.
1. Your SwiftShield™ is a piece of heavy equipment and the act of covering and uncovering
your boat should be treated with respect and good judgment. Children should not operate the
cover without strict adult supervision.
2. When operating the cover mechanism, keep limbs and fingers away from any possible pinch
points.
3. Restrict Children and Adults from playing near the SwiftShield™ mechanism.
4. Before operating the SwiftShield™, be sure that nothing will interfere with it’s operating path.
5. Do not hang from cover mechanism and or add any additional weight to the system.
6. Be sure that the Boat is positioned properly on the boat lift. If boat is not positioned correctly,
the SwiftShield™ mechanism could strike the boat causing damage.
7. Make sure hydraulic lines are clear from any pinch points before operating the SwiftShield™
Mechanism.
8. When Operating the SwiftShield™, be sure to keep an eye on the cover so that it does not
get caught on any part of the boat. If the fabric gets caught it could tear.
9. When operating the SwiftShield™, be sure that the mechanisms arms do not interfere with
any boat guide-ons.
10. Do not use the power pack for storage purposes. Articles or tools in box could cause damage
to the pump or electrical items.
11. SunStream®recommends not operating the SwiftShield™ in winds above 25mph .
12. SunStream®recommends securing your cover by the tie down points when winds are
between 40mph-70mph.
13. SunStream®recommends removing your cover when winds are to exceed 70mph.
NOTICE:
WARNING:
FORM NO. 660843 REV. B PAGE 4
SwiftShield™
Overview
SwiftShield™ Cover
Roller Tube
Bow Sprit
Guide Ropes
Cross Bar
I-Beam
Hanger
Cylinder
Side
Rail
Piling
Piling Lift I-Beam
Guide Post
Bow Sprit
Spreader Pipe
Upper Arm
Fin Plate
Cylinder Mount
Tube
Side Rail
Clamp
FORM NO. 660843 REV. B PAGE 5
SwiftShield™
Overview
Continued
*Lines shown disconnected
Battery
Power Pack Box
RC Unit
Hydraulic Pump Hydraulic Lines*
from SwiftShield™
Cylinders
SunFluid
Reservoir
FORM NO. 660843 REV. B PAGE 6
ASSEMBLY INSTRUCTIONS
If you have any questions during the assembly process, please call your local dealer or
SunStream® at (253) 395-0500.
SunStream® recommends at least 2 people for assembly.
Before beginning assembly, find a nice flat area with room to work and set up your parts. Read
ahead to the installation procedure to determine the best location to start.
Tools Required:
SunStream® recommends the tools below for easier and quicker assembly.
Box Knife (to open packaging)
9/16” Socket
3/4” Socket
7/8” Socket, or adjustable wrench
1” Socket, or adjustable wrench
Socket wrench
Torque wrench (ft-lbs)
1/2” Combination wrench
9/16” Combination wrench
3/4” Combination wrench
32mm Open end wrench, or adjustable wrench
Pipe wrench with at least 2” opening
Diagonal cutters
Hacksaw
Mallet
Anti-Seize (to be used on all threaded fasteners)
Cable ties
3/16” Allen wrench
7/32” Allen wrench
Needle nose pliers
Snap ring pliers
Large Flat head screw driver
Tape measure
Recommended Tools:
Cordless drill
13/32” drill bit
Small adjustable wrench
Level
SunFluid
Torque values: 3/8-16 SS Bolt 20 lb-ft
FORM NO. 660843 REV. B PAGE 7
1-A
Assembling the Bow Sprit Clamp
Step 1
Assembling and Installing the Bow Sprit
Insert aft clamp into long
forward tube
FORM NO. 660843 REV. B PAGE 8
1-B
Clamping the Bow Sprit to the I-Beam
Steps:
1. Bow Sprit to be centered between the bunks.
2. Apply anti-seize to bolt threads before installing nuts.
3. Clamp bow sprit to I-beam with bolts and nuts.
Bolt SS, 3/8-16 X 8”,
Fully Threaded
4 Places
Nut SS, Nylok,
3/8-16, 4 Places
FORM NO. 660843 REV. B PAGE 9
1-C
Inserting the Bow Sprit forward tube
Bolt SS
3/8-16 X 3.5”
Nut SS
Nylok 3/8-16
Steps:
1. Insert bow sprit extension into bow sprit.
2. Apply anti-seize to bolt threads before
installing nut.
3. Final length to be determined after roller
has been installed.
Bow Sprit Extension
Bow Sprit
FORM NO. 660843 REV. B PAGE 10
1-D
Inserting and securing the Spreader Pipe
Spreader Pipe
Cotter Pin, SS
2 Places
Steps:
1. Insert spreader pipe into hole in bow sprit
extension.
2. Lock in place with cotter pins
Altri manuali per SWIFTSHIELD A Series
1
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Sunstream Sistema di sollevamento
Manuali Sistema di sollevamento popolari di altre marche
Genie
Genie Z-60/34 Manuale utente
Screen Technics
Screen Technics INTERFIT Vertical Up Lift Manuale utente
Mortuary Lift
Mortuary Lift ULTIMATE 1000 Manuale utente
Custom Equipment
Custom Equipment Hy-Brid 3 Series Manuale di programmazione
Custom Equipment
Custom Equipment Hy-Brid Lifts 2 Series Manuale di programmazione
Hy-Brid Lifts
Hy-Brid Lifts HB-P3.6 Manuale di programmazione
