Suntor ST30NMT Manuale utente
1
ST30NMT User Manual
2
Contents
Ⅰ、 Product Appearance............................................................................................................................................. 3
Ⅱ、Product Intro............................................................................................................................................................. 3
Ⅲ、Equipment Install.....................................................................................................................................................4
3.1 Interfaces Describe............................................................................................................................................ 4
3.2 Basic Parameters................................................................................................................................................ 5
3.3 Cautions................................................................................................................................................................ 5
Ⅳ、Equipment Debug....................................................................................................................................................6
4.1 Prepare of Debug...............................................................................................................................................6
4.2 Equipment Login................................................................................................................................................ 7
4.3 Set Central Node/ Access Node.................................................................................................................... 7
4.4 Modify IP Address..............................................................................................................................................8
4.5 Set WLAN............................................................................................................................................................. 9
4.6 Set Bandwidth..................................................................................................................................................... 9
Ⅴ、Use Notes................................................................................................................................................................. 10
Ⅵ、Normal Faults and Treatment.......................................................................................................................... 11
Ⅶ、Accessories.............................................................................................................................................................. 12
Focus on wireless make transmission easier（End）.......................................................................................13
3
Ⅰ、Product Appearance
Ⅱ、Product Intro
The ST15MPT UAV wireless transmission link is an Ad-hoc network device, it's good
performance in NLOS transmission. The device wireless module adopt Qualcomm
chip and two-frequency design, it support 1.4G（1427.9-1447.9MHz）and 800M
（806-826MHz）. When it's in 1.4G frequency, it can realize a high throughput Ad-hoc
network transmission in a long LOS distance. When it's in 800M frequency, it can
realize fast mobile Ad-hoc network transmission in a NLOS complex environment. In
our testing, the NLOS distance is 1-3KM, the LOS distance is 10-20KM.
The ST15MPT RF power is 300mW, its features of low power consumption, small in
size, quick to install, strong penetration transmission and long range advantages, is
very suitable application for manpack video transmission, UAV, Unmanned ship,
4
Unmanned car, Airship, Target drone, Powered parachute, Robot and other fields for
video signal transmission, police video forensics, emergency monitor and rescue sites.
Ⅲ、Equipment Install
3.1 Interfaces Describe
No.
Item
Function describe
1.
Power
DC 12V, two ping
2.
Antenna Connector
SMA
3.
TTL Data Serial Port
Also accept customized RS232 data
4.
Signal Indicator
Signal Connection
5.
Power Indicator
Power on, the light will turn on
6.
Ethernet Indicator
IP video transmission then light turn on
5
7.
RJ45 Eth interface
connect to devices： IPC，Switch，PC，etc.
3.2 Basic Parameters
N.W.:200g
G.W.:265g(including two antenna)
3.3 Cautions
The device data interface is designed by air plug. If it needs to be extended during
use, please use the direct network cable. The direct network cable sequence is defined
as follows:
6
Special attention: before the equipment is powered on, please carefully confirm
whether the antenna is correctly connected, so as to avoid unnecessary trouble and
economic loss caused by damage to the equipment.
Ⅳ、Equipment Debug
4.1 Prepare of Debug
Before debugging, ensure that PC and device IP in the same network segment.
Factory default parameters: IPv4 address: 192.168.1.1; Subnet mask: 255.255.255.0;
The IP of the computer should be set to 192.168.1.x (X= any number between 2 and
253, which does not conflict with the device address).
The subnet mask：255.255.255.0。
The steps to modify computer IP:
7
4.2 Equipment Login
1. Open IE browser, input the IP of the device in the address bar: 192.168.1.12,
log in the device and select "Management Login", the default IP of the device
is: 192.168.1.12, username and password is: admin123.
2. User name: admin123 password：admin123 click login
choose“Management Login”
8
4.3 Set Central Node/ Access Node
The device has two working modes: Central Node/ Access Node. After logging into
the device through the browser, the following actions are required to change the
device's working mode. After entering the page, click "Master and Slave Setting",
select "Master and Slave Setting" to set the device's working mode, and click "OK" to
complete the configuration. As shown in figure:
4.4 Modify IP Address
Enter the device IP address in the browser and enter the device management p
User name：admin123
password：admin123
click login
Select the working mode of the node,
Central Node/Access Node
9
age. Click "Network Parameter Setting" and select "IP setting" to modify the de
vice IP address. Click "OK" to complete IP modification， as shown in figure:
4.5 Set WLAN
When setting the working frequency of the device, click the "Wireless Setting" button
and select the "Frequency Band" option to enter the operation interface. The device
supports the RF 800M frequency band and 1.4G frequency band. The 2.4G frequency
band is not open yet. After confirming the frequency, click "Submit" to complete the
configuration. The operation is as follows:
Set an IP
10
4.6 Set Bandwidth
According to the link throughput demand, users can choose channel bandwidth 1.4, 3,
5, 10, 20 MHz. The narrower the bandwidth, the farther the transmission distance, the
lower the bandwidth, the closer the transmission distance, and the higher the
transmission rate. Different electromagnetic environments exist in different
environments. The frequency can be adjusted to avoid channel interference and
achieve better transmission effect. Click "Wireless Setting", select "Bandwidth", select
the bandwidth and click "OK" to complete the configuration. Operation as shown
below:
Set the frequency band
800MHz/1.4GHz
click "Submit"
Indice
Altri manuali Suntor Trasmettitore
Suntor
Suntor ST30HPT Manuale utente
Suntor
Suntor ST20NPT Manuale utente
Suntor
Suntor ST6200BM Guida all'installazione
Suntor
Suntor ST6200TPS-SD Manuale utente
Suntor
Suntor CD15NMT-MiNi Manuale utente
Suntor
Suntor ST15NMT-MiNi Manuale utente
Suntor
Suntor ST6210SH Manuale utente
Suntor
Suntor ST6200TPS-HD Manuale utente
