Swisher FC11544BSXP Manuale utente

44” FINISH CUT

TRAIL MOWER

OWNER’S

MANUAL

SWISHER

1602 CORPORATE DRIVE, WARRENSBURG, MISSOURI 64093

PHONE 660 747 8183 FAX 660 747 8650

MODEL NO.

STARTING SERIAL # L112-341001

Assembly

Operation

Service and Adjustment

Repair Parts

Made In The

USA

Rev 12 341

swisherinc.com

10662

FC11544BS

FC11544BSXP

FC12544BS

FC12544BSXP

POL11544D

POL11544DEX

Read and follow all

Safety Precautions

and Instructions

before operating this

equipment.

IMPORTANT

CHANGING YOUR LANDSCAPE SINCE 1945

LIMITED WARRANTY

The manufacturer’s arranty to the original consumer purchaser is: This product is free from

defects in materials and orkmanship for a period of one (1) year from the date of purchase

by the original consumer purchaser. We ill repair or replace, at our discretion, parts found to

be defective due to materials or orkmanship. This arranty is subject to the follo ing

limitations and exclusions:

1) Engine Warranty All engines utilized on our products has a separate arranty

extended to them by the individual engine manufacturer. Any

engine service difficulty is the responsibility of the engine

manufacturer and in no ay is S isher or its agents responsible

for the engine arranty. The Briggs & Stratton Engine Service

Hot Line is 1-800-233-3723.

2) Commercial Use This product is not intended for commercial use and carries no

commercial arranty.

3) Limitations This arranty applies only to products, hich have been

properly assembled, adjusted, and operated in accordance ith

the instructions contained ithin this manual. This arranty

does not apply to any product of S isher that has been subject

to alteration, misuse, abuse, improper assembly or installation,

shipping damage, or to normal ear of the product.

4) Exclusions Excluded from this arranty are normal ear, normal

adjustments, and normal maintenance.

In the event you have a claim under this arranty, you must return the product to an

authorized service dealer. All transportation charges, damage, or loss incurred during

transportation of parts submitted for replacement or repair under this arranty shall be borne

by the purchaser. Should you have any questions concerning this arranty, please contact us

toll-free at 1-800-222-8183. The model number, serial number, date of purchase, and the

name of the authorized S isher dealer from hom you purchased the mo er ill be needed

before any arranty claim can be processed.

THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME

PERIODS STATED HEREIN FOR ALL EXPRESSED WARRANTIES. Some states do not

allo the limitation of consequential damages or limitations on ho long an implied arranty

may last, so the above limitations or exclusions may not apply to you. This arranty gives

you specific legal rights and you may have other rights, hich vary from state-to-state. This is

a limited arranty as defined by the Magnuson-Moss Act of 1975.

This Safety Alert Symbol indicates important messages in this

manual. When you see this symbol, carefully read the message that

follows and be alert to the possibility of personal injury.

Read this manual completely. This machine can amputate hands, feet, and

throw objects. Failure to observe the following safety instructions could

result in serious injury or death.

SAFETY PRECAUTIONS

• Read the manual. Learn to operate this machine safely.

•Al ays disconnect the spark plug ire and place the ire here it

cannot contact the spark plug, to prevent accidental starting of the engine

hen setting up, transporting, adjusting or making repairs.

• Keep all shields and guards in place.

• Understand the speed, steering and stability of this machine. Kno

the positions and operations of all controls before you operate this

machine. Check all of the controls in a safe area before starting to ork

ith this machine.

• Clear the area of objects such as rocks, toys, ire, etc. that can be

picked up and thro n by the blade.

• Allo only responsible adults ho are familiar ith these instructions

to operate this machine. Never allow children to operate this machine.

• Be sure the area is clear of other people before mo ing. Be a are of the

mo er discharge direction and do not point at anyone. Stop the machine

if anyone enters the mo ing area. Children are often attracted to the

machine and the mo ing activity. Never assume that children will

remain where you last saw them.Keep children under the atchful care

of another responsible adult.

•No riders!

• Turn off the blades hen not mo ing. Before leaving the machine, turn off the

blades and stop the engine.

• Watch for traffic hen operating near or crossing road ays.

• Do not operate the mo er if the mo er has been dropped or damaged

in any manner or if it vibrates excessively. Excessive vibration is an

indication of damage. Repair mo er as necessary.

• Dress properly. Do not operate the mo er hen barefoot or

earing open sandals. Wear only solid shoes ith good traction hen

mo ing.

• Do not operate the machine hile under the influence of alcohol or

drugs.

• Operate self-propelled machines up and do n slopes. There is

significant risk of overturns hen operating across slopes. Operate alk-

behind machines across slopes. There is a significant risk of slipping

under a alk-behind machine hen operating up and do n slopes. Do not

operate on slopes greater than 15 degrees.

• Never tamper ith safety devices. Check their proper operation

regularly.

• Stop and inspect the equipment if you strike an object. Repair, if

necessary, before restarting.

• Never make adjustments or repairs ith the engine running.

• Mo er blades are sharp and can cut. Wrap the blades or ear gloves,

and use extra caution hen servicing them.

• Do not put hands or feet near or under rotating parts. Keep clear of

the discharge opening at all times.

• Do not mo in reverse. Always look down and behind before and while

backing.

OD36 Deflector Decal

OD45 Warning Decal

OD29 Danger Decal

Engine Serial #

OD11 No Step Decal

OD15 Void Warranty Decal

OD33 Speed Decal

OD55 Triangle Danger Decal

(All four deck corners)

Trail Mower Serial #

SAFETY DECALS

Replace decal immediately if damaged. Order by part number from S isher.

OD99125 Medium Swisher

Logo Decal

OD99127 44" Deck Decal

OPERATING YOUR TRAIL MOWER

INTENDED USE

The 44” Trail Mo er is designed to produce a quality finish cut on la ns, golf courses,

etc. It is not intended to clear brush or cut saplings. Your Trail Mo er should be

to ed behind an ATV, golf cart, la n tractor, or other approved vehicle. It is not

designed for speeds exceeding 5 MPH. WARNING: To avoid serious injury,

operate your mo er up and do n the face of slopes, NEVER across the face. DO

NOT MOW SLOPES GREATER THAN 15 DEGREES! (See attached guide for

sighting slopes.)

ATTACHING TRAIL MOWER TO TOW VEHICLE

• Back vehicle up to desired to ing position.

• Offset the Trail Mo er to the side opposite the to vehicle discharge (if any).

This prevents the to vehicle from thro ing grass into Trail Mo er engine.

• If to vehicle has a ball hitch, the ball must be removed before hitch can be

fastened.

• Attach hitch to the to vehicle ith hitch pin (H11). Make certain the hitch

pin goes completely through and is clipped to prevent accidental separation.

• Securely attach safety tether (6736) to to vehicle and to the Trail Mo er

toggle s itch located on right side of the engine. The safety tether ill stop the

Trail Mo er engine either manually or if the t o should become separated. It is

very important that the safety tether is securely attached to both the toggle

switch and to the tow vehicle. See Fig 3, pg 15.

The operation of any mo er can produce foreign objects to be thro n into the

eyes, resulting in severe eye damage. Al ays ear certified safety glasses or

ide-vision safety goggles over spectacles before staring any cutting machine

and hile operating such a machine.

The operation of any cutter produces sound aves that are damaging to the

human ear. Ear protection is recommended.

CAUTION!

Tragic accidents can occur if the operator is not alert to the presence of

children. Children are often attracted to the machine and the mo ing

activity. Never assume that children will remain where you last saw

them.

TRANSPORTING MOWER

• Stop Trail Mo er.

• Place Trail Mo er deck in its highest position.

• When transporting ithout the use of a to vehicle, remove spark plug

ire and place it here it cannot contact the spark plug.

• Set vehicle parking brake or chock heels to prevent accidental rolling.

• Start engine properly.

• Slo ly engage blade control.

• In a safe environment, i.e. no children, allo blades to rotate and engine to

idle for 5 minutes. This breaks in the belts and the engine.

• Stop mo er properly.

ENGAGING BLADES

The Trail Mo er ill not start if the blade lever is in the “ENGAGED” position.

• Engage blades by rotating blade lever into the “ENGAGED” position.

• Rotate blade lever in opposite direction to disengage blade.

• The dual braking system is applied hen the blades become disengaged. It is

designed to bring the blades to quick stop (approximately 7 seconds). Each

Trail Mo er brake system has been tested and calibrated. For safety, the

consumer should not alter the braking system.

STARTING THE ENGINE

See engine manufacturer’s recommendations for the type and amount of oil and fuel

used. Trail Mo ers equipped ith an electric start engine ill need a battery (sold

separately). S isher recommends using a standard “12N12A” battery.

• Make sure the to vehicle parking brake is set, mo er is level, and blades are

disengaged. Engine must be level to accurately check and fill oil. Do not overfill.

• Check spark plug ire, oil, and fuel.

• Check all electrical connections for buildup or debris.

• Make sure toggle s itch is not turned “OFF” and safety tether is attached.

• Set engine throttle to “RUN” position.

• Move the choke lever to the “ON” position (cold engine only).

• With feet clear of mo er deck, turn key s itch to the “START” position; release

hen engine begins to run (12 volt models). Recoil models must use pull-rope.

Pull rope ith a single fluid motion.

• Set engine throttle at maximum RPM.

• Allo engine to run a fe moments before engaging blades.

BREAKING IN YOUR MOWER

CAUTION!

SHUT OFF MOWER ENGINE AND REMOVE SPARK PLUG WIRE FROM

SPARK PLUG BEFORE MAKING ANY ADJUSTMENTS TO THE MOWER.

IMPORTANT: This engine is not equipped with a spark arrester muffler. It is a violation of

California Public Resource Code Section 444 to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land. Other states or federal areas may have similar laws.

• There is approximately 1 ½” to 4 ½” of height adjustment.

• Rotate height adjust crank handle in a clock ise direction to lift the mo er

deck. A counter-clock ise direction is used to lo er the mo er deck.

• Graduated scales are for reference only, not the actual cutter height.

• Bring to vehicle to a complete stop, shut off engine, and set parking brake.

• Disengage blades.

• Manually shut toggle s itch and/or key s itch to their “OFF” positions.

• Al ays remember to remove keys to avoid irresponsible usage (electric start

models only).

• Adjust the cutting height.

• Double check vehicle to mo er attachment.

• Start mo er engine and set throttle to “FAST” for best cutting performance.

• Slo ly engage blade clutch lever.

• Carefully mount vehicle and start mo ing at a slo travel speed.

• S isher recommends if the to vehicle is equipped ith a mid-mount mo er

to overlap the cut approximately 6”. This may vary depending on mo ing

terrain, obstacles, and/or to vehicle. Al ays keep SAFETY the first priority.

• If the to vehicle is not equipped ith a mid-mount mo er, e still

recommend offsetting the mo er so that the to vehicle does not crush the

grass.

• Make adjustments hile Trail Mo er is not running.

• Remove hairpins NB127 from clevis pins 18842 so L-hitch 18829 can

be repositioned.

• Raise or lo er hitch section to obtain proper front to back adjustment.

• Insert clevis pins in the desired hitch position and secure ith hairpins.

MOWER HEIGHT ADJUSTMENT

• Make adjustments hile Trail Mo er is not running.

FRONT TO BACK ADJUSTMENT

For best cutting results, the mo ing deck should be raised to ½” to ¾” higher in

the rear.

TOW HITCH OFFSET

This Trail Mo er has been designed to operate offset from the center of the to

vehicle or consecutively ith another Trail Mo er, providing additional cutting

idth. When offsetting the mo er do so to the side opposite the discharge of the to

vehicle.

STARTING TO MOW

STOPPING THE MOWING SESSION

SUGGESTED MOWING PRACTICES

• Operate mo er engine at full throttle to assure the best cutting performance and

maximum material discharge.

• Allo et grass to dry. Wet grass ill clump and collect under the mo ing deck.

• Mo ing should be started ith to vehicle in lo gear and increased only as safe

mo ing conditions permit. Mo ing speed should not exceed 5 MPH.

• The average la n should be cut to approximately 2.5” during the cool season and to

over 3” during the hot months.

• For a healthier la n and better aesthetics, your la n should be mo ed often and

after moderate gro th.

• When cutting high or dense grass areas go slo ly. Some areas may need to be

mo ed t ice. The second cut should be at 90 degrees to the first, if possible.

•Mowing thick or high grass: Raise rear of deck to ½” to ¾” above front of the

deck. See “FRONT TO BACK ADJUSTMENT”. When mo ing thick or high grass,

it is recommended to cut area t ice. The first at a higher setting and the second at the

desired la n height.

•Creating a manicured lawn: Never cut more than 1/3 of the grass height in one

cutting.

GENERAL TROUBLE SHOOTING

The mo er is not cutting level.

• Check air pressure of all tires; make sure they are equal. See tires for

maximum inflation.

• Make certain blades are installed identically, ithout the engine running.

The engine ill not start.

• Disengage blades, turn toggle s itch to “OFF” position, check battery and all

other electrical connections, and inspect spark plug and ire.

• Contact engine manufacturer or qualified mechanic.

Engine runs poorly.

• See engine manual.

• Check the throttle adjuster.

• Replace fuel, clean fuel filter and fuel line.

• Check spark plug and gap.

Mo er bounces excessively hile to ing.

• Decrease tire pressure.

• To at a slo er speed.

IF PROBLEMS PERSIST HAVE A QUALIFIED MECHANIC SERVICE THE

MOWER. NEVER ATTEMPT TO MAKE AN ADJUSTMENT THAT YOU

ARE NOT SURE IS CORRECT. DOING SO CAN CAUSE OTHER

PROBLEMS.

MOWER MAINTENANCE

GENERAL RECOMMENDATIONS

The arranty on this Trail Mo er does not cover items that have been subjected to

operator abuse or negligence. To receive full value from the arranty, operator must

maintain unit as instructed in this manual.

Some adjustments ill need to be made periodically to maintain your unit properly.

All adjustments in this manual should be checked at least once each season.

BEFORE EACH USE

• Check engine oil level on a level surface. Check t ice to ensure an accurate

reading.

• Check condition of air filter; clean and replace as necessary.

• Check blade operation; keep blades in good condition.

• Check for loose fasteners and tighten them as needed.

AFTER EACH USE

• Keep blades sharp.

• Remove fresh grass clippings ith garden hose.

• Hardened grass clippings on underside should be scraped out ith a putty

knife.

• Keep fluids at proper levels.

• Cover unit to prevent rain or other debris buildup. Definitely cover the

engine.

BEFORE AND/OR AFTER EACH SEASON

• Replace the spark plug.

• Clean or replace the air filter.

• A ne spark plug and clean air filter assure proper air-fuel mixture and help

your engine run better and last longer.

• Check blades and belts for ear. Replace as necessary.

• Change the oil.

• See engine manufacturer’s recommendations for servicing.

STORAGE RECOMMENDATIONS

CAUTION! Do not store engine indoors or other poorly ventilated area. Keep

engine a ay from gas appliances and ater heaters here fumes could contact

open flame, pilot lights, or sparks.

If engine is to be stored for 30 or more days, prepare unit as follows:

· Drain fuel outside into an approved container.

· Start engine properly and run until unit is out of fuel.

· Let engine cool.

· Remove remaining gasoline from carburetor and fuel tank to prevent gum

deposits from forming ithin the engine. Gum deposits can cause

malfunction in the engine.

· Store mo er ith blades disengaged to prevent belts from being permanently

stretched.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Swisher Taglia erba

Swisher

Swisher T14560A Manuale utente

Swisher

Swisher QuadBoss QBRT10544 Manuale utente

Swisher

Swisher ZT2452 Manuale utente

Swisher

Swisher Predator WB924 Manuale utente

Swisher

Swisher L213-224001 Manuale utente

Swisher

Swisher ST60022Q Manuale utente

Swisher

Swisher The Predator WB11524 Manuale utente

Swisher

Swisher Trim-Max STD4422HO Manuale utente

Swisher

Swisher POL 14560 Manuale utente

Swisher

Swisher POL1250F Manuale utente

Swisher

Swisher L116-336001 Manuale utente

Swisher

Swisher WB942 Manuale utente

Swisher

Swisher ST60022 Manuale utente

Swisher

Swisher T1360 Manuale utente

Swisher

Swisher WRC10224HC Manuale utente

Swisher

Swisher FC10544CL Manuale utente

Swisher

Swisher PST5022 Manuale utente

Swisher

Swisher T11544A Manuale utente

Swisher

Swisher POL 14560 Manuale utente

Swisher

Swisher ZT2454 Manuale utente

Swisher

Swisher T11044, T11544, T10544BSPB, T1 Manuale utente

Swisher

Swisher T1260F Manuale utente

Swisher

Swisher ZTR2454CL Manuale utente

Swisher

Swisher ZT2350 Manuale utente

Manuali Taglia erba popolari di altre marche

RHINO

RHINO 1958 Manuale utente

Wolf Garten

Wolf Garten Compact plus 40 B Manuale utente

Cub Cadet

Cub Cadet LTX 1045 Manuale utente

Craftsman

Craftsman 917.378461 Manuale utente

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Manuale utente

Challenge

Challenge CH18V2 Istruzioni operative

TALEN TOOLS

TALEN TOOLS AVR HGM30 Manuale utente

DEWEZE

DEWEZE ATM-725 Manuale operativo

Weed Eater

Weed Eater 180083 Manuale utente

Husqvarna

Husqvarna Poulan Pro PP185A42 Manuale utente

Better Outdoor Products

Better Outdoor Products Quick Series Manuale utente

Cub Cadet

Cub Cadet 23HP Z-Force 60 Manuale operativo

MTD

MTD 795, 792, 791, 790 Manuale utente

Toro

Toro Groundsmaster 3505-D Manuale utente

Dennis

Dennis FT 610 Manuale utente

AIRFORCE

AIRFORCE F-15 Gen 3 Manuale utente

MTD

MTD 126-220-000 Manuale utente

Toro

Toro 74806 Manuale utente