Symbol PrintPAD Manuale utente

PrintPAD

Print PAD

Symbol reserves the right to make changes to any product to improve reliability,

function, or design.

Symbol does not assume any product liability arising out of, or in connection with, the

application or use of any product, circuit, or application described herein.

No license is granted, either expressly or by implication,estoppel, or otherwise under

any patent right or patent, covering or relating to any combination, system,

apparatus, machine, material, method, or process in which Symbol products might

be used. An implied license exists only for equipment, circuits, and subsystems

contained in Symbol products.

Symbol and the Symbol logo are registered trademarks of Symbol Technologies, Inc.

Other product names mentioned in this manual may be trademarks or registered

trademarks of their respective companies and are hereby acknowledged.

Symbol Technologies, Inc.

One Symbol Plaza

Holtsville, N.Y. 11742-1300

http://www.symbol.com

Quick Reference

Introduction

The PrintPAD provides portable printing in the most rugged

environments with Symbol portable terminals (SPT 1700/1800,

PPT 2700/2800, PDT 8000 and PDT 8100). Portable printing

enablestheproductionofhardcopy back-upsofdigitalinformation

and signature printing, as well as the generation of receipts or

tickets for your mobile computing applications.

About This Guide

This guide describes how to set up and use the printer. Specific

topics covered include:

•Parts of the Printer on page 2

•Charging the Batteries on page 3

•Inserting the Terminal on page 4

•Installing Paper on page 4

•Charge LED Indications on page 6

•Replacing Batteries on page 7

•Supplies on page 7

•Regulatory Information on page 8

•Service Information on backcover.

For detailed information on portable terminals, see the Quick

Reference Guide or Product Reference Guide for the terminal.

PrintPAD

Parts of the Printer

Paper Cavity

Battery Well

Self Test

Button

Data Port

Power Port

Charge

LED

Roller

Print Head

Release Level

BatteryRetaining

Clip

Quick Reference

Preparing the Batteries for Operation

Caution: Remove the battery insulation label before operating

the printer.

The PrintPAD ships with two batteries installed. Prior to operation,

remove the two red isolator labels.

Charging the Batteries

1. Plug the power supply connector into the printer power con-

nector.

2. Plug the AC adapter into an appropriate power source.

The Charge LED turns red when charging and turns green when

fully charged. A complete charge will take approximately 6 hours.

PrintPAD

You can determine the relative battery capacity by printing a self-

test, see “Printing a Self-Test” on page 6. On the printout, “Battery

Volt” will vary between 6.8 volts and 8.4 volts.

Inserting the Terminal

There are three PrintPAD

configurationsthatacceptsthe

following terminals:

• PPT 2700, PPT 2800,

SPT 1700 and SPT 1800

Series terminals

• PDT 8100 Series termi-

nals

• PDT 8000 Series termi-

nals.

Insert the terminal into the

cavityandpress downuntilthe

terminal is firmly seated.

Installing Paper

1. Press a new roll of pa-

per into the paper cav-

ity. Ensure the end of

the roll exits from the

bottom of the paper

cavity.

End of Roll

Quick Reference

2. Open the print head by

raising the grey print

headreleaseleveruntil

it stops. The lever will

click at the partial open

position, do not stop

here, continue until it is

fully open.

3. Wake up the printer by

momentarily pressing

the red self-test button.

4. Feed the end of the pa-

per into the paper en-

trance (under the black

roller) until the paper

exits the top of the print

head.Ensurethepaper

exits straight.

PrintPAD

5. Lower the grey print

head release lever.

6. Feed the paper end

through the printer cover.

7. Close and latch cover.

Printing a Self-Test

Open the printer cover and

press the red self-test button

until the printer starts to print.

Once printing starts release

the self-test button.

Charge LED Indications

Charge LED State of Charge Action

Solid Red Charge in progress. Wait for green LED

Green Charge completed. None

Red flash – slow Battery is too cold.

Battery is disconnected. Change environment.

Connect battery.

Red flash – fast High temperature. Change environment.

Red/orange – slow Battery voltage very low. Wait for solid red. Restart

charge.

Red/orange – fast Battery not connected. Connect Battery.

Orange flash – slow Charge Timeout. Restart Charge.

Quick Reference

Replacing Batteries

1. Open the printer by unsnapping the latch on the front of the

case.

2. Remove the batteries by pressing the retainer clip outward

with thumb. While pressing the retainer clip, lift the outside

end of the battery past the retainer clip.

3. Remove the red insulation label from each new battery.

4. Insert new batteries. Ensure the battery contacts are facing

down and are on the outside edge of the printer.

Supplies

Use only supplies certified by the Original Equipment

Manufacturer (OEM). For OEM supplies, please contact O’Neil

Printer Supplies Group at 949-458-6400 or Symbol Customer

Support Center.

PrintPAD

Regulatory Information

All Symbol devices are designed to be compliant with rules and regulations in

locations they are sold and will be labeled as required.

Any changes or modifications to Symbol Technologies equipment, not expressly

approved by Symbol Technologies, could void the user’s authority to operate the

equipment.

Radio Frequency Interference Requirements

Note: This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However there is no

guarantee that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected

• Consult the dealer or an experienced radio/TV technician for help.

Radio Frequency Interference Requirements - Canada

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Marking and European Economic Area (EEA)

Statement of Compliance

Symbol Technologies, Inc., hereby declares that this device is in compliance with all

the applicable Directives, 89/336/EEC, 73/23/EEC. A Declaration of Conformity may

be obtained from http://www2.symbol.com/doc/.

Tested to comply

with FCC Standards

FOR HOME OR OFFICE USE

Indice

Altri manuali Symbol Stampante

Symbol

Symbol RP 1000 Manuale utente

Manuali Stampante popolari di altre marche

Lexmark

Lexmark 1400 Series Manuale

Canon

Canon i70 Series Manuale utente

Evolis

Evolis Elypso Manuale utente

Kyocera

Kyocera FS-9530DN Manuale utente

Canon

Canon LASER SHOT LBP-1210 Manuale utente

Samsung

Samsung BIXOLON SRP-350plusF Manuale utente

Canon

Canon PIXMA PRO-1 Series Manuale utente

Canon

Canon PIXMA G3560 Guida all'installazione

Dell

Dell Color Laser Printer 2130cn Manuale utente

Tektronix

Tektronix Phaser 840 Manuale utente

Epson

Epson ET-7750 Istruzioni operative

Canon

Canon CLBR 460ps Manuale utente

Eltron

Eltron P210 Guide Manuale utente

Ricoh

Ricoh MD-P1 Manuale utente

Epson

Epson SC-F7100 series Manuale utente

Epson

Epson Stylus C40UX Manuale utente

Canon

Canon imagePASS-A2 Manuale utente

Canon

Canon S820D Manuale utente