Talitor BW1101 Manuale utente
Quad Digital Wireless
Transmitter module
(Model No. BW1101)
User Guide
V.1
111228
- 2 -
Thank you for purchasing our Quad Digital Wireless Transmitter module.
Please read this manual before installation.
For customer support, please contact your dealer, and keep your Invoice for
further support.
Do not open/modify the device, as it may cause damage to the unit and
void the Warranty. For internal repairs, consult your dealer or an Authorized
Service Center.
Do not use any accessories other than what comes with the unit otherwise, it
would void the warranty.
Protect from humidity. Do not put it in water and be careful to protect it
from rain, sea water, or high humidity environment etc.
Protect from high temperatures
To avoid damage or mis-operation of the device, only use it in the temperature
between 0 ~ +40°C.
Do not bring
the device suddenly from a hot to a cold place, or vice versa.
This may cause damaged to the inside of the unit by creating condensation.
EU Environmental Protection
The symbol of crossed-out garbage shows that this product should not be
treated as household waste, and it falls into the category of electric /electronic
equipment for recycling. This electronic device should not be disposed in a
regular trash. We strongly advice you to contact related authorization before
you dispose this product.
3
Package contains
Transmitter module x1
AV in Cable (10 pin, freewire) x 1
Power in/out Cable (4 pin, freewire) x 1
AV in Cable (10 pin)
Power in/out Cable (4 pin)
User’s Interfaces
Get unit work quickly
1. Connect power to #BW1101, and turn the Power Switch to “Power On” position; Power
LED (red) will be on.
2. Connect A/V in Cable to camera
4
3. Pair #BW1101 with any of the below suitable Digital Wireless Receivers.
4. How to Pair: Select a channel at Receiver, and long press the pairing button on the
Receiver till the Channel LED (blue) is flashing, then press the pairing button on the
transmitter module to enter pairing process, after pairing is completed and successful,
the Channel LED on Receiver will be flashing rapidly.
* During pairing, the transmitter link LED will be flashing interactively (Red and Yellow) for data
transmission; and please put transmitter and receiver as close as possible to prevent failure
due to other interference.
Technical Specification
Item Spec
Frequency 2400 – 2483.5MHz
Output Power 0 dBm(TYP) @ Max power setting
Rx sensitivity
(BER<=1E-3)
-90dBm(TYP) @1M mode
-85dBm(TYP) @3M mode
Modulation GFSK
Hard interface 14pin header(1.27mm)
Dimension W/L/H , 19mm/27mm/7.3mm
Supply voltage 3.3Vdc
Current consumption 150mA(TYP) @ Tx power = 18.5dBm
35mA(TYP) @ Rx mode
Operating temperature 0~50degree
#CW1104-
Quad Digital Wireless DVR
#CW1106-
Quad 7" LCD Digital Wireless DVR
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Non-modification Statement:
Changesormodificationsnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidtheuser's
authoritytooperatetheequipment.
Validity of using the module certification:
In the event that these conditions cannot be met (for example certain laptop configurations or co-location
with another transmitter), then the FCC authorization for this module in combination with the host
equipment is no longer considered valid and the FCC ID of the module cannot be used on the final
product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization.
Custom design antennas may be used, however the OEM installer must following the FCC 15.21
requirements and verify if new FCC approval will be necessary.
Indice
