TDK-Lambda PHV Series Guida utente

IEEE DIGITAL INTERFACE SETUP MANUAL FOR

PHV Series High Voltage

POWER SUPPLY

Document: 83550130 Rev A

TDK-LAMBDA AMERICAS

405 Essex Road, Neptune, NJ 07753

Tel: (732) 922-9300

Fax: (732) 922-9334

Web: www.us.tdk-lambda.com/hp

THIS PAGE LEFT INTENTIONALLY BLANK

83550130 Revision A

Table of Contents

1. Overview...................................................................................................................................3

1.1. Scope........................................................................................................................................3

1.2. ADDR LED................................................................................................................................3

1.3. Service Request (SRQ) LED.....................................................................................................3

2. Interface setup information........................................................................................................5

2.1. GPIB primary address (PA).......................................................................................................5

2.2. Other DIP switch settings..........................................................................................................5

83550130 Revision A

THIS PAGE LEFT INTENTIONALLY BLANK

83550130 Revision A

1. Overview

1.1. Scope

This manual applies to PHV series power supplies equipped with the IEEE digital interface

option. The manual describes setting the GPIB interface address only.

The IEEE interface programming commands can be found in the Digital Interface

Command Reference manual (document 83550100) downloadable from the PHV product

page: http://www.us.tdk-lambda.com/hp/product_html/PHVpower.htm.

The IEEE interface is located on the rear panel of the power supply. A sketch is shown

below.

IEEE Interface features

1- IEEE-488 interface connector

2- Configuration DIP switch (see section 2.1)

3- Interface Addressed LED (see section 1.2)

4- Service Request LED (see section 1.3

1.2. ADDR LED

This LED illuminates when the interface is either in listener addressed state or talker

addressed state.

1.3. Service Request (SRQ) LED

This LED illuminates when the interface asserts the SRQ line. After a serial poll the LED

extinguishes.

83550130 Revision A

THIS PAGE LEFT INTENTIONALLY BLANK

83550130 Revision A

2. Interface setup information

For normal operation, only the GPIB primary address should be adjusted using switches 1

through 5 if required. The other switches, 6 through 8 remain in the OFF position.

2.1. GPIB primary address (PA)

The GPIB primaryaddress (PA) enables identification of all units connected to an IEEE-488

bus system, and each unit connected to the bus must be assigned a unique PA.

The Host PC usually has PA=0 and the connected units usually have addresses from 4

upwards. Normally PHV power supplies arefactory configured with the PA set to 8.

The user can change the factory set PA via a DIP switch located on the IEEE-488 interface

converter on the rear panel of the unit (see the figure on page 3). It is not necessary to

open the power supply.

After changing a configuration switch, the power supply should be turned off for 5 seconds

and turned on again.

To change the GPIB PA, the user should only change switches 1 through 5. The unit is

factory set with switch 4 in the ON position and switches 1, 2, 3, and 5 are in the OFF

position (PA=8).

The switch settings follow the binary system:

Switch 1 has value 1

Switch 2 has value 2

Switch 3 has value 4

Switch 4 has value 8

Switch 5 has value 16

Example: To set the GPIB PA to 9, Switches 1 and 4 are ON, switches 2, 3, and 5 are

OFF. To set the GPIB PA to 20, Switches 3 and 5 are ON, switches 1, 2, and 4 are OFF.

2.2. Other DIP switch settings

DIP switches 6, 7, and 8 are special functions and are factory set to the OFF position and

the settings should not be changed. Contact the factory for further information.

Altri manuali per PHV Series

Indice

Altri manuali TDK-Lambda Alimentazione elettrica

TDK-Lambda

TDK-Lambda ELC12 Series Manuale utente

TDK-Lambda

TDK-Lambda Z+ series Manuale utente

TDK-Lambda

TDK-Lambda CHVM3 Series Manuale utente

TDK-Lambda

TDK-Lambda ZUP Series Manuale utente

TDK-Lambda

TDK-Lambda Z+ series Manuale utente

TDK-Lambda

TDK-Lambda CUT35 Series Manuale utente

TDK-Lambda

TDK-Lambda CPFE1000FI Series Manuale utente

TDK-Lambda

TDK-Lambda NVM175 Manuale utente

TDK-Lambda

TDK-Lambda ZWX Series Manuale utente

TDK-Lambda

TDK-Lambda CN-A24 Series Manuale utente

TDK-Lambda

TDK-Lambda Genesys Manuale utente

TDK-Lambda

TDK-Lambda TPS4000 Series Manuale utente

TDK-Lambda

TDK-Lambda DPP480-XX-3 Manuale del proprietario

TDK-Lambda

TDK-Lambda HFE1600-48 Manuale utente

TDK-Lambda

TDK-Lambda ZWS300RC Series Manuale utente

TDK-Lambda

TDK-Lambda Genesys GEN6-100 Manuale utente

TDK-Lambda

TDK-Lambda GENESYS GH1.5kW in 1U Half-Rack 0-600V /... Manuale utente

TDK-Lambda

TDK-Lambda ZWD150PAF Series Manuale utente

TDK-Lambda

TDK-Lambda IM-LZSA1000-2 Manuale utente

TDK-Lambda

TDK-Lambda GENESYS GEN 2400W Series Manuale utente

TDK-Lambda

TDK-Lambda DPP480-XX-3 Manuale utente

TDK-Lambda

TDK-Lambda GENESYS 1500W Manuale utente

TDK-Lambda

TDK-Lambda CSS65 Manuale utente

TDK-Lambda

TDK-Lambda CM4 Supplemento

Manuali Alimentazione elettrica popolari di altre marche

Monacor

Monacor PS-12CCD Manuale utente

VOLTIMA

VOLTIMA MagicBox 15 Manuale utente

Agilent Technologies

Agilent Technologies 6032A Manuale utente

Miller

Miller Auto Deltaweld 452 Manuale utente

BCP

BCP PUOUBK Foglio di istruzioni

HC 2210 Manuale utente

Puls

Puls CT5.241 Manuale utente

OCZ

OCZ ZX1250W Manuale utente

iseg

iseg ECH 238 Manuale utente

Power

Power XXL A Series Manuale utente

Agilent Technologies

Agilent Technologies 6631B Manuale utente

Renogy

Renogy PHOENIX 300 Manuale utente

HP 6200B Manuale di servizio

Epson

Epson Stylus Scan 2500 Manuale operativo

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manuale utente

Puls

Puls MiniLine ML50.100 Manuale utente

Puls

Puls AS-Interface SLA4.100 Manuale utente

Kenwood

Kenwood PS-60 Manuale utente