TE Connectivity CERTI-CRIMP Manuale utente

Instruction Sheet

1 of 5

*Trademark

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.

PRODUCT INFORMATION

1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com.

408-35023

20 MAR 17 Rev A

Tool

Terminal

Wire

Part Number

Crimping Chamber Marking

Strip PN

Loose Piece PN

Range, mm²

Insulation Diameter Range, mm

675930-1

0.5-1.5

160430

160490

0.5-1.5

2.3-3.3

160433

160493

1.0-2.5

160429

160491

1.0-2.5

3.1-3.8

160431

160492

Figure 1

INTRODUCTION

CERTI-CRIMP Hand Crimping Tool 675930-1 is designed to crimp FASTON* .187 Series receptacles onto wire

sizes 0.5-1.5 mm² and 1.0-2.5 mm². Refer to Figure 1.

NOTE

Read these instructions thoroughly before using the hand tool.

NOTE

Dimensions in this instruction sheet are in metric units [with U.S. customary units in brackets]. Figures and illustrations are for

reference only and are not drawn to scale.

Reasons for reissue of this instruction sheet are provided in Section 7, REVISION SUMMARY.

PROPER USE GUIDELINES

Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools

are intended for occasional use and low volume applications. A wide selection of powered application

equipment for extended-use, production operations is available.

CERTI-CRIMP* Hand Crimping Tool;

PN 675930-1

Locator

Indenter Jaw

Insulation Adjustment Pin

Ratchet

Back Side of Tool

Link

Anvil Jaw

1.0 –2.5

Crimping Chamber Markings

0.5 –1.5

408-35023

Rev A

2 of 5

DESCRIPTION

Each hand tool features two jaws (anvil and indenter), a locator, an insulation adjustment pin, and a ratchet.

When closed, the jaws form two crimping chambers each marked on the BACK side of the tool with the letters

A and B. The wire size range is marked on the link. See Figure 1.

The locator positions the receptacle in the jaws and aids in locating the wire in the receptacle. The insulation

adjustment pin is used to regulate the crimp height of the insulation barrel of the receptacle. The ratchet

assures full crimping of the receptacle. Once engaged, the ratchet will not release until the tool handles have

been FULLY closed.

CAUTION

The jaws bottom before the ratchet releases. This design feature ensures maximum electrical and tensile performance of the

crimp. DO NOT re-adjust the ratchet.

CRIMPING PROCEDURE

Select the appropriate receptacle and wire size for the hand tool. The wire size and insulation diameter must be

within the specified range for the receptacle. Strip the wire to the length shown in Figure 2. DO NOT nick or cut

the wire strands. Then, proceed as follows:

Figure 2

1. Hold tool so that the BACK side is facing you.

2. Open the jaws by squeezing the tool handles together until the ratchet releases.

3. Center the receptacle wire barrel in the appropriate nest of the anvil jaw (refer to Figure 1). Make sure

the tool locator enters the receptacle locator slot. See Figure 3.

Figure 3

Hand Tool

Strip Length

675930-1

5.0 mm [.196]

Wire Barrel

Locator Slot

Insulation Barrel

Wire Strip Length

(See Table)

Locator Wire Slot

Back Side of Tool

Receptacle Locator Slot

Nest of Anvil Jaw

Stripped Wire

408-35023

Rev A

3 of 5

4. Holding the receptacle in place, squeeze the tool handles together just enough to hold the receptacle

in the jaws.

CAUTION

Squeezing the handles together excessively will deform the wire barrel.

5. Insert the stripped wire into the receptacle insulation barrel and through the wire slot of the tool locator

until the wire insulation butts against the locator. See Figure 3.

6. Holding the wire in place, squeeze the tool handles together until the ratchet releases.

7. Allow the tool handles to open FULLY and remove the crimped receptacle from the tool.

INSULATION CRIMP ADJUSTMENT

Each tool has three insulation adjustment positions to adjust the wire insulation grip: 1-Small, 2-Medium, and 3-

Large. To determine the proper insulation crimp setting, proceed as follows:

1. Insert the adjustment pin into Position 3 as shown in Figure 1.

2. Position the receptacle into the jaws as described in Section 3, CRIMPING PROCEDURE.

3. Insert an UNSTRIPPED wire into just the insulation barrel of the receptacle. Crimp the receptacle and

remove it from the jaws.

4. Check the insulation support by bending the wire back and forth once. The insulation barrel should

retain grip on the wire insulation. If the wire pulls out, move the insulation adjustment pin to the next

smaller position (2) and perform another test crimp. If the wire does not pull out, the pins are properly

adjusted.

Move the insulation adjustment pin as necessary until the desired insulation grip is obtained. The crimp should

hold the wire insulation firmly without cutting into it.

MAINTENANCE AND INSPECTION PROCEDURE

It is recommended that a maintenance and inspection program be performed periodically to ensure dependable

and uniform terminations. Though recommendations call for at least one inspection a month, frequency of

inspection depends on:

The care, amount of use, and handling of the hand tool,

The presence of abnormal amounts of dust and dirt,

The degree of operator skill, and,

The established standards of the facility.

The hand tool is inspected before being shipped; however, it is recommended that the tool be inspected

immediately upon arrival to ensure that the tool has not been damaged during shipment.

5.1. Daily Maintenance

1. Hand tool should be immersed (handles partially closed) in a reliable commercial degreasing

compound to remove accumulated dirt, grease, and foreign matter. When degreasing compound is

not available, tool may be wiped clean with a soft, lint-free cloth. DO NOT use hard or abrasive objects

that could damage the tool.

2. Make certain that the retaining pins are in place and that they are secured with retaining rings.

3. All pins, pivot points, and bearing surfaces should be protected with a THIN coat of any good SAE 20

motor oil. DO NOT oil excessively.

4. When the tool is not in use, keep handles closed to prevent objects from becoming lodged in the jaws.

Store the tool in a clean, dry area.

SAE is a trademark.

408-35023

Rev A

4 of 5

5.2. Periodic Inspection

Lubrication

Lubricate all pins, pivot points, and bearing surfaces with SAE 20 motor oil as follows:

Tool used in daily production - lubricate daily

Tool used daily (occasional) - lubricate weekly

Tool used weekly - lubricate monthly

Wipe excess oil from tool, particularly from crimping area. Oil transferred from the crimping area onto

certain terminations may affect the electrical characteristics of an application.

Visual Inspection

1. Close the tool handles until the ratchet releases and then allow them to open freely. If they do not

open quickly and fully, the spring is defective and must be replaced. See Section 6, REPLACEMENT

AND REPAIR.

2. Inspect the jaws for worn, cracked, or broken areas. If damage is evident, return the tool for evaluation

and repair. See Section 6, REPLACEMENT AND REPAIR.

Crimp Height Inspection

Crimp height inspection is performed through the use of a micrometer with a modified anvil, commonly

referred to as a crimp-height comparator. TE does not manufacture or market crimp-height comparators.

Detailed information on obtaining and using crimp height comparators can be found in Instruction Sheet

408-7424.

Proceed as follows:

1. Select a receptacle and maximum size wire for each crimping chamber.

2. Refer to Section 3, CRIMPING PROCEDURE, and crimp the receptacle accordingly.

3. Measure the wire barrel crimp height as shown in Figure 4. If the crimp height conforms to that height,

the tool is considered dimensionally correct. If not, return the tool for evaluation and repair. See

Section 6, REPLACEMENT AND REPAIR.

Figure 4

Ratchet Inspection

1. Select a receptacle and maximum size wire for the tool.

2. Position the receptacle and wire between the jaws as described in Section 3, CRIMPING

PROCEDURE.

Hand Tool

Maximum Wire Size

Crimp Height

± 0.05 [.002]

675930-1

1.5

1.40 [.055]

2.5

1.52 [.060]

Position Point on Center of

Wire Barrel Opposite Seam

Modified Anvil

Crimp Height

(See Table)

408-35023

Rev A

5 of 5

3. Hold the wire in place and squeeze the handles until the ratchet releases. Hold the handles in this

position, maintaining just enough tension to keep the jaws closed.

4. Check the clearance between the bottoming surfaces of the jaws. If the clearance is 0.025 mm [.001

in.] or less, the ratchet is satisfactory. If clearance exceeds 0.025 mm [.001 in.], the ratchet is out of

adjustment and must be repaired. See Section 6, REPLACEMENT AND REPAIR.

REPLACEMENT AND REPAIR

Customer-replaceable parts are listed in Figure 5. A complete inventory can be stocked and controlled to

prevent lost time when replacement of parts is necessary. Order replacement parts through your TE

Representative, or call 1-800-526-5142, or send a facsimile of your purchase order to 717-986-7605, or write

to:

CUSTOMER SERVICE (038-035)

TE CONNECTIVITY CORPORATION

PO BOX 3608

HARRISBURG PA 17105-3608

For tool evaluation and customer repair service, call 1-800-526-5136.

REPLACEMENT PARTS

Item

Part Number

Description

Qty Per Tool

21045-3

RING, External Crescent Retaining, .188-in. D Shaft

8-59558-2

PIN, Retaining, .187-in. D x .521 in. L

21045-6

RING, External Crescent Retaining, .250-in. D Shaft

2-23620-9

PIN, Retaining, .250-in. C x .838 in. L

39364

SPRING, Handle

39207

ADJUSTMENT PIN, Insulation Crimp

Figure 5

REVISION SUMMARY

Initial Release

3 4

279.4 [11.00]

76.2 [3.00] (Closed)

22.22 [.875]

Weight: 539 g [1 lb 3 oz]

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali TE Connectivity Utensili per crimpatura

TE Connectivity

TE Connectivity SDE-SA Manuale utente

TE Connectivity

TE Connectivity SDE-SA Manuale utente

TE Connectivity

TE Connectivity PRO-CRIMPER III Manuale utente

TE Connectivity

TE Connectivity 543344- 1 Manuale utente

TE Connectivity

TE Connectivity SDE-SA Manuale utente

TE Connectivity

TE Connectivity PRO-CRIMPER III 2161732-1 Manuale utente

TE Connectivity

TE Connectivity ERGOCRIMP 4-1579001-1 Manuale utente

TE Connectivity

TE Connectivity SDE-SA Manuale utente

TE Connectivity

TE Connectivity 2063490-1 Manuale utente

TE Connectivity

TE Connectivity 2217480 Series Guida di riferimento

TE Connectivity

TE Connectivity FDH 3000 864 Manuale utente

TE Connectivity

TE Connectivity CERTI-CRIMP II Manuale utente

TE Connectivity

TE Connectivity 2392900-1 Manuale utente

TE Connectivity

TE Connectivity 2392637-1 Manuale utente

TE Connectivity

TE Connectivity 90084 Manuale utente

TE Connectivity

TE Connectivity 2391789-1 Manuale utente

TE Connectivity

TE Connectivity PDT-48-00 Manuale utente

TE Connectivity

TE Connectivity SOLISTRAND 69097 Manuale utente

TE Connectivity

TE Connectivity 2844594-1 Manuale utente

TE Connectivity

TE Connectivity 575937 Manuale utente

TE Connectivity

TE Connectivity 58425 Series Manuale utente

TE Connectivity

TE Connectivity 2031973-1 Manuale utente

TE Connectivity

TE Connectivity 68321-1 Manuale utente

TE Connectivity

TE Connectivity 2407132-1 Manuale utente

Manuali Utensili per crimpatura popolari di altre marche

Panduit

Panduit CT-1000 Guida per l'amministratore

JST

JST CS 10 Manuale utente

molex

molex 63811-5100 Manuale utente

Danfoss

Danfoss ET4200 Manuale utente

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manuale utente

molex

molex 63825-3000 Manuale utente

Tyco Electronics

Tyco Electronics 69156-1 Manuale utente

CRH

CRH CRL CBLHCT1 Manuale utente

Emerson

Emerson Klauke ES 105CFM Manuale utente

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Manuale di istruzioni

Danfoss

Danfoss ET4350 Manuale utente

Milwaukee

Milwaukee M18 Manuale utente

HOGERT

HOGERT HT1P169 Manuale utente

Textron

Textron ESG105L Manuale utente

Tyco Electronics

Tyco Electronics 90035-3 Manuale utente

Emerson

Emerson Klauke ES 20RMCCFB Manuale utente

Continental Refrigerator

Continental Refrigerator PC150HD Manuale utente

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manuale utente