TE Connectivity SDE-SA Manuale utente

Instruction Sheet

1 of 7

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.

PRODUCT INFORMATION

1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com.

408-35291

7 JUN 2022 Rev A

PROPER USE GUIDELINES

Cumulative trauma disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional

use and low-volume applications. A wide selection of powered application equipment is available for extended-use production operations.

The SDE-SA hand tool is a commercial-grade tool. Product crimped with this tool meets the wire barrel crimp height requirement for hand

tools in the appropriate 114 application specification, but might not comply with other feature parameters of the specification.

Figure 1: SDE-SA Commercial Hand Tool Assembly 2389146-1 with Die Assembly 2389146-2

Die set 2389146-2

M3x5.0 socket head screws

Handle

Wire hex anvil

Ferrule stop

Die-retaining screws (2)

Wire hex crimper

Stationary jaw

Die-retaining pins (4)

Braid hex crimper

Moving jaw

Braid hex anvil

Ratchet adjustment wheel

SDE-SA Commercial Hand Tool Assembly

PN 2389146-1 with

Die Assembly PN 2389146-2

Rev A

2 of 7

1. INTRODUCTION

SDE-SA Commercial Hand Tool Assembly 2389146-1 for the Contact Kit, Ferrule, RTK031 Low Loss HF

FAKRA 90, is the tool and die set shown in Figure 1. The tool consists of the SDE Crimp Hand Tool Frame

2362810-1 (instruction sheet 408-35143) and the die assembly listed in Figure 1. This tool is used to crimp the

terminal part numbers listed in Table 1.

Table 1: Crimping specifications

Crimp tooling

Contact kit

Wire type

Strip length mm [in.]

SDE-SA tool

Die assembly only

2389146-1

2389146-2

1718080

1719252

Low loss

RTK031

Inner conductor

2.8 +0.2/-0.3

Dielectric

5.3 +0.2/-0.3

Braid

9.8 +0.2/-0.3

NOTE

Dimensions in this instruction sheet are in millimeters with [inches in brackets]. Figures are for reference only and are not

drawn to scale.

Read these instructions thoroughly before crimping connectors.

2. DESCRIPTION

The tool frame features two jaws, a handle, a ratchet adjustment wheel, and an emergency ratchet release.

Each die set consists of a crimper (upper die) and an anvil (lower die). The tool frame holds a die assembly

with one crimping chamber (see Figure 1). Die-retaining pins and die-retaining screws are used to secure the

dies in the tool frame.

The tool features a ratchet and an adjustment wheel with a range of settings. The ratchet ensures that the tool

has completed the cycle and does not release until the handles have been fully closed, unless the emergency

ratchet release is rotated to manually release the ratchet. The adjustment wheel controls the amount of handle

pressure exerted on the dies during the crimping procedure.

CAUTION

The dies bottom before the ratchet releases. This feature ensures maximum tensile performance of the crimp. Do not re-

adjust the ratchet unless you have verified that the crimp height is incorrect (see section 7, ADJUSTING THE RATCHET).

Rev A

3 of 7

3. INSTALLING THE DIE SET

1. Open the tool handles and remove the two die-retaining screws from the tool jaws (Figure 1).

2. Place the wire anvil and insulation anvil so that their chamfered sides and the marked surfaces face

outward when mounted in the moving jaw of the tool frame.

3. Insert the two die-retaining pins.

4. Insert one of the short die-retaining screws through the jaw and the anvil dies. Tighten the screw just

enough to hold the die in place. Do not tighten the screw completely.

5. Place the wire crimper and insulation crimper so that the chamfered sides and the marked surface face

outward when mounted in the stationary jaw of the tool frame.

6. Insert the two die-retaining pins.

7. Insert the other short die-retaining screw through the jaw and the crimper dies. Tighten the screw just

enough to hold the die in place. Do not tighten the screw completely.

8. While making sure the anvil and crimper align properly, close the tool handles until the ratchet in the

tool frame engages sufficiently to hold the anvil and crimper in place.

9. Tighten both die-retaining screws.

10. Attach the ferrule stop to the wire hex crimper with two M3x5.0 socket head screws.

4. REMOVING THE DIE SET

1. Close the tool handles until the ratchet releases.

2. Remove the two M3x5.0 screws, the two die-retaining screws, and the four die-retaining pins.

3. Slide the anvils and crimpers out of the tool jaws.

NOTE

The ratchet release has detents with audible clicks as the handles are closed. The ratchet releases on the sixth click.

Rev A

4 of 7

5. CRIMPING

NOTE

The tool is provided with a crimp adjustment feature. Initially, the crimp height should be verified as specified in Figure 3. Refer

to section 6, INSPECTING THE CRIMP HEIGHT, and section 7, ADJUSTING THE RATCHET, to verify crimp height before

using the tool to crimp contacts and wire sizes.

1. Refer to Table 1 and select wire of the specified size and insulation diameter.

2. Strip the wire to the length indicated. Do not nick or cut wire strands.

3. Select an applicable ferrule and identify the appropriate crimp section according to the wire size

markings on the tool.

4. Position the strands of the wire braid.

5. Slip the ferrule over the wire braid until it stubs with the shoulder of the rear shell subassembly or of the

front shell subassembly. This is the ferrule’s end position (Figure 2).

NOTE

Ensure that the strands of the wire braid do not protrude over the knurling. The strands must not be visible after positioning

the ferrule. This prevents the strands from becoming stuck between the ferrule and the shoulder of the rear or front shell

subassemblies.

6. While holding the wire in place, fully cycle the tool until the ratchet releases and allows the handle to

open.

Figure 2: Positioning the ferrule

End position

No wire strands visible

Crimped ferrule

Rev A

5 of 7

6. INSPECTING THE CRIMP HEIGHT

Crimp height inspection is performed using a micrometer with a modified anvil, commonly referred to as a

crimp-height comparator. TE Connectivity does not manufacture or market crimp height comparators. Detailed

information on obtaining and using crimp-height comparators can be found in instruction sheet 408-7424.

1. Refer to Table 1 and select a wire (maximum size) for each crimp section listed.

2. Refer to section 5, CRIMPING, and crimp the contacts accordingly.

3. Using a crimp height comparator, measure the wire barrel crimp height listed in Table 2.

If the crimp height conforms to that shown in the table, the tool is considered dimensionally correct.

If not, adjust the tool. Refer to section 7, ADJUSTING THE RATCHET.

CAUTION

Do not use damaged product. If a damaged contact is evident, replace it. Do not re-terminate contacts.

Figure 3: Crimp height

Modified anvil

Position point on center of wire barrel opposite seam

Crimp height (see Table 2)

Table 2: Crimp height specifications

Die assembly

Wire type

Crimp height mm [in.]

2389146-2

Low loss RTK031

Wire

3.9±0.1 [.154±.004]

Braid

4.52±0.05 [.178±.002]

Rev A

6 of 7

7. ADJUSTING THE RATCHET

The ratchet is preset prior to shipment, but it is important to verify the crimp height using a micrometer or

caliper. Use and wear can cause the tool to go out of adjustment. Inspect the crimp height and adjust the

ratchet, if necessary, on a regular basis. Refer to Figure 4 and adjust as follows:

If the crimp height is larger than recommended, remove the ratchet wheel adjustment screw and rotate

the adjustment wheel counterclockwise () to a higher setting. Reinstall the screw. Repeat as

required.

If the crimp height is smaller than recommended, remove the ratchet wheel adjustment screw and

rotate the adjustment wheel clockwise (–) to a lower setting. Reinstall the screw. Repeat as required.

If the crimp height cannot be made to conform to the recommended crimp height, replace the tool or

die set. See section 9, REPLACEMENT AND REPAIR.

Figure 4: Ratchet adjustment

Adjustment screw

Ratchet adjustment wheel

8. MAINTENANCE AND INSPECTION

8.1. Maintenance

Remove dust, moisture, and other contaminants with a clean, soft brush or soft, lint-free cloth. Do not

use objects that could damage the dies or tool.

When the tool is not in use, keep the handles closed to prevent objects from becoming lodged in the

dies. Store the tool in a clean, dry area.

Remove all lubrication and accumulated film by immersing the dies in a suitable commercial degreaser.

8.2. Visual inspection

Inspect the tool and dies on a regular basis to ensure that they are not worn or damaged.

Make sure that the die retaining screws are properly secured.

Inspect the crimping chambers of the die assembly for flattened, chipped, worn, or broken areas. If

damage or abnormal wear is evident, replace the dies. Refer to section 9, REPLACEMENT AND

REPAIR.

Rev A

7 of 7

9. REPLACEMENT AND REPAIR

If the dies are damaged or worn excessively, they must be replaced. Order replacement dies through your TE

representative. You can also order parts by any of the following methods:

Go to TE.com and click the Shop TE link at the top of the page.

Call 800-522-6752.

Write to:

CUSTOMER SERVICE (038-035)

TE CONNECTIVITY CORPORATION

PO BOX 3608

HARRISBURG PA 17105-3608

For customer repair services, call 800-522-6752.

10. REVISION SUMMARY

Revisions to this instruction sheet include:

Initial release

Altri manuali per SDE-SA

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali TE Connectivity Utensili elettrici

TE Connectivity

TE Connectivity 2031676-1 Manuale utente

TE Connectivity

TE Connectivity 59275 Manuale utente

TE Connectivity

TE Connectivity ERGOCRIMP 7-1579004-1 Manuale utente

TE Connectivity

TE Connectivity 2217074-1 Manuale utente

TE Connectivity

TE Connectivity 2390879-1 Manuale utente

TE Connectivity

TE Connectivity HPi 10 TE Manuale di istruzioni

TE Connectivity

TE Connectivity 2844990-1 Guida di riferimento

TE Connectivity

TE Connectivity PRO- CRIMPER III Manuale utente

TE Connectivity

TE Connectivity HT40 Manuale utente

TE Connectivity

TE Connectivity ERGOCRIMP Manuale utente

TE Connectivity

TE Connectivity SOLARLOK PN 1-1579004-1 Manuale utente

TE Connectivity

TE Connectivity 46447 Manuale utente

TE Connectivity

TE Connectivity 2381460-1 Manuale utente

TE Connectivity

TE Connectivity 2385850-1 Manuale utente

TE Connectivity

TE Connectivity 2377026-1 Manuale utente

TE Connectivity

TE Connectivity SDE-SA Manuale utente

TE Connectivity

TE Connectivity 2395361-1 Manuale utente

TE Connectivity

TE Connectivity HT11K Manuale utente

TE Connectivity

TE Connectivity 1976330-1 Manuale utente

TE Connectivity

TE Connectivity Micro-MaTch 528405-9 Manuale utente

TE Connectivity

TE Connectivity 2363758-1 Manuale utente

TE Connectivity

TE Connectivity HT11K Manuale utente

TE Connectivity

TE Connectivity 2393337-1 Manuale utente

TE Connectivity

TE Connectivity 58536-1 Manuale utente

Manuali Utensili elettrici popolari di altre marche

AEG

AEG OMNI-JS Manuale utente

SIP

SIP 01533 Manuale utente

Ribimex

Ribimex PRS499 Manuale utente

3M Fiber Optic Connector Crimp Tool Manuale utente

Ryobi

Ryobi P524 Manuale utente

ROJEK

ROJEK FSN 300A Manuale utente

Kemper

Kemper 1740PRO Manuale utente

WABCO

WABCO OptiTire Manuale utente

EINHELL

EINHELL TE-MS 18/210 Li Manuale utente

Orgapack

Orgapack OR-T 85 Guida rapida

TOUGHCUT

TOUGHCUT Diamond 400 Manuale utente

Yaros

Yaros PB-3603 Manuale utente

Fein

Fein BSS 2.0 E Guida all'installazione

Baileigh Industrial

Baileigh Industrial SS-2725 Manuale utente

Milwaukee

Milwaukee 2674-20 Manuale utente

Fein

Fein BLs 1.6 Manuale utente

Princess

Princess Electric Multi Sharpener Manuale utente

FOREDOM

FOREDOM K.1050 Manuale