Tech4o Alti-Ski Manuale utente
1
ALTI - SKI WATCH
2
3
1.0 Introduction/Features:
•
Altimeter w/cumulative assent/descent
• Barometer
• Temperature
• Ski Run Counter
• Time / date / alarm
To make the most of your purchase, be sure to carefully read this
manual and follow the included ow chart. Keep them safe for
future reference.
Please follow these precautions in using and
caring for your new Tech4o Alti-Ski Watch:
• Avoid exposing the watch to extreme conditions
• Avoid rough use and/or severe impacts
• Occasionally clean the watch with a soft and moistened cloth
• Store the watch in a clean, dry place when not in use for an
extended period of time.
Tech4o Alti-Ski Watch™
Owner's Manual
Content:
1.0 Introduction/Features
1.1 Button Functions
1.2 Major Function Modes
2.0 Time / Date Mode - Display
2.1 Time / Date Mode - Setting
3.0 Daily Alarm Mode - Display
3.1 Daily Alarm Mode - Setting
4.0 Countdown Timer Mode - Display
4.1 Countdown Timer Mode - Setting
4.2 Countdown Timer Mode
5.0 Stopwatch Mode - Display
5.1 Stopwatch Mode - Setting
5.2 Stopwatch Mode - Using the Stopwatch
6.0 Stopwatch History Mode - Display
6.1 Stopwatch History Mode - Navigating Data
7.0 Alternate Time Zone Mode - Display
7.1 Alternate Time Zone Mode - Setting
8.0 Temperature Mode - Display
8.1 Temperature Mode - Setting
8.2 Temperature Mode - Temperature Features
9.0 Altimeter Mode - Display
9.1 Altimeter Mode - Setting
9.2 Altimeter Mode - Max Altitude
9.3 Altimeter Mode - Barometric Pressure
10.0 Descent Mode - Display
10.1 Descent Mode - Trip Descent
10.2 Descent Mode - Rate of Descent
10.3 Descent Mode - Max Rate of Descent
10.4 Descent Mode - Total Daily Descent
10.5 Descent Mode - Total Lifetime Descent
11.0 Ascent Mode - Display
11.1 Ascent Mode - Trip Ascent
11.2 Ascent Mode - Rate of Ascent
11.3 Ascent Mode - Max Rate of Ascent
11.4 Ascent Mode - Total Daily Ascent
11.5 Ascent Mode - Total Lifetime Ascent
12.0 Run Counter - Display
12.1 Run Counter - Trip Run Counter
12.2 Run Counter - Daily Run Counter
12.3 Run Counter - Lifetime Run Counter
13.0 Limited Warranty
4
5
1.1 Button Functions On/Off
Mode Button: [M]
Used to select among the main modes of the
watch
Button: [o/o]
Used to conrm selections, start/stop the
stopwatch, and lock/unlock altitude
Set/+ Button: [s/+]
Used to access setting mode and increase/
change digits during setting display. Also sets
intermediate/lap times in stopwatch mode
Option/- Button: [o/-]
Used to decrease/change digits during setting display and browse
through sub-functions
Light Button: [L]
Used to illuminate the watch face for use during low light conditions
1.2 Major Function Modes
Press any button to wake the watch from sleep mode. Press the [M]
button to toggle among the main function modes.
2.0 Time / Date Mode - Display
When Time / Date mode is selected, the
watch will display the current time
on the top row and the current date,
temperature, or ski run counter on the
bottom row.
• To view time mode, press the [m] button
until the mode indicator displays the
clock symbol.
TIME
TEMPERATURE
ALTIMIETER
ASCENT
RUN
DESCENT
6
7
2.1 Time / Date Mode - Setting
• In Time / Date mode press and hold the Set/+ button [s/+] for
two seconds.
• The 12 H / 24 H will ash. Use the [o/-] button to select between
a 12 or 24 hour clock feature. Press the [o/o] button to conrm
selection.
• The hours will ash. Use the [s/+] and [o/-] buttons to select the
correct hour. Press the [o/o] button to conrm selection.
• The minutes will ash. Use the [s/+] and [o/-] buttons to select
the correct minutes. Press the [o/o] button to conrm selection.
• The month will ash. Use the [s/+] and [o/-] buttons to select the
correct month. Press the [o/o] button to conrm selection.
• The days will ash. Use the [s/+] and [o/-] buttons to select the
correct day. Press the [o/o] button to conrm selection.
• The year will ash. Use the [s/+] and [o/-] buttons to select the
correct year. Press the [o/o] button to conrm selection.
• You have now completed the Date / Time Mode quick set.
3.0 Daily Alarm Mode - Display
This watch includes a daily alarm. When the daily alarm is ON, the
alarm will sound for 30 seconds at the
alarm time every day.
• To view the daily alarm display, press
the [o/-] button once while in time/date
mode.
• When the daily alarm is selected, the
watch will display the alarm setting
indicator in the top row and the daily
alarm time in the bottom row.
3.1 Daily Alarm Mode - Setting
• To set the daily alarm, press and hold the [s/+] button for 2
seconds. The hours will ash.
• Use the [s/+] and [o/-] buttons to adjust the hours. Press the [o/o]
button to conrm selection.
• At this time, the minutes will ash.
• Use the [s/+] and [o/-] buttons to adjust the minutes. Press the
[o/o] button to conrm selection.
• Press the [o/o] button again to set the alarm for on or off.
continues
8
9
Press the [o/-] button to conrm selection and advance to the
countdown timer mode.
4.0 Countdown Timer Mode - Display
This watch includes a countdown timer.
• To view the countdown timer, press the
[o/-] button twice while in time/date
mode.
• When the countdown timer is selected,
the watch will display the countdown
time in the top row and the current home
time in the bottom row.
4.1 Countdown Timer Mode - Setting
• To set the countdown timer, press and hold the [s/+] button for 2
seconds. The hours will ash.
• Use the [s/+] and [o/-] buttons to adjust the hours. Press the [o/o]
button to conrm selection.
• At this time, the minutes will ash.
• Use the [s/+] and [o/-] buttons to adjust the minutes. Press the
[o/o] button to conrm selection.
• Use the [s/+] and [o/-] buttons to adjust the seconds. Press the
[o/o] button to conrm selection and nish.
4.2 Countdown Timer Mode
Using the Countdown Timer
• When in countdown timer mode, press the [o/o] button to
start the countdown.
• Press the [o/o] button again to stop the countdown.
• Press the [o/o] button again to resume the countdown
• When the countdown timer expires the alarm will sound for
30 seconds and the timer will reset to the last countdown
timer setting.
• Press the [o/-] button to proceed to the Stopwatch Mode.
5.0 Stopwatch Mode - Display
This watch features 5 individual
stopwatch counters.
• The measuring unit of the stopwatch
is 1/100 seconds for the rst 59
minutes, 59.99 seconds. After
reaching 1 hour of cumulative time,
the measuring unit changes to 1
second and the measuring range is 99
hours, 59 minutes, 59 seconds
continues
10
11
• To view the stopwatch, press the [o/-] button three times while in
date/time mode.
• When the stopwatch is selected, the watch will display StP 1 in the
top row and 0:00 in the bottom row.
5.1 Stopwatch Mode - Setting
• In stopwatch mode, press and hold the [s/+] button for two
seconds.
• The LAP/INT indicator will ash.
• Both LAP and intermediate settings will record time the same way,
but the way the information is displayed will vary. The LAP setting
will show the last lap time when the [s/+] or [o/o] buttons are
pushed and in stopwatch history mode. The Intermediate setting
will show the cumulative intermediate times when the [s/+] or
[o/o] buttons are pushed and in stopwatch history mode.
• Use the [o/-] button to select between LAP and int settings. Press
the [o/o] button to conrm selection.
5.2 Stopwatch Mode - Using the Stopwatch
How to use the Stopwatch
• When in stopwatch mode, press the [o/o] button to start the
stopwatch. The top row will now display ------------- and the
bottom row will display the current stopwatch time.
• Press the [o/o] button again to stop the stopwatch. The top and
bottom rows will now display current stopwatch time.
• Press the [o/o] button again to resume the stopwatch. The top row
will now display ------------- and the bottom row will display the
current stopwatch time.
• While the stopwatch is running, you may enter LAP/INT times by
pressing the [s/+] button. The top row will display the rst LAP/
INT time and the bottom row will display the cumulative stopwatch
time.
• After each successive LAP/INT time is entered, the top row will
display:
* the cumulative time of all the entered intermediate times
if the int setting was selected; or
* the last lap time if the lap setting was selected.
• The bottom row will display the cumulative stopwatch time.
• When the stopwatch is stopped, press the [o/-] button to proceed
to the stopwatch history mode or press [s/+] to proceed to the
next available stopwatch to begin recording another set of times
following the steps above. Note: there are 5 available stopwatches.
More stopwatch information can be recorded by clearing
stopwatch data in the stopwatch history mode or by recording
over stopwatch #5.
12
13
6.0 Stopwatch History Mode - Display
When the stopwatch history mode is
selected the watch will display St HSt on
the top row and the current home time
on the bottom row depending on your
selection made in temperature mode.
• To access the stopwatch history mode,
press the [o/-] button 4 times while in
time/date mode.
6.1 Stopwatch History Mode - Navigating Data
How to retrieve saved stopwatch information:
• To view saved stopwatch information, press the [o/o] button in
stopwatch history mode to view the desired history log
• Press the [o/-] button to conrm selection and view the desired
data.
• Continue pressing the [o/-] button to scroll through the different
LAP/INT times for that stopwatch log
• Press [o/o] button at any time to view a different stopwatch log.
• To clear all saved stopwatch data, press and hold the [s/+] button
while selecting a stopwatch log to view.
7.0 Alternate Time Zone Mode - Display
When the alternate time zone mode is
selected the watch will display TIME 2
and the alternate time zone time in the
top row and the home time mode in the
bottom row.
• To view the alternate time zone display,
press the [o/-] button 5 times while in
time/date mode.
7.1 Alternate Time Zone Mode - Setting
• In the alternate time zone mode, press and hold the Set/+ button
[s/+] for two seconds.
• The hours will ash. Use the [s/+] and [o/-] buttons to select the
correct hour, making sure to account for a.m. A, or p.m. P.
• Press the [o/o] button to conrm selection.
• The minutes will ash. Use the [s/+] and [o/-] buttons to select
the correct minutes.
• Press the [o/o] button to conrm your selection.
• The alternate time zone is now set. Press the [o/-] to home time
display.
14
15
8.0 Temperature Mode - Display
• To view temperature mode, press the [m]
button until the mode indicator displays T.
• In temperature mode the watch will
display temperatures in the top row and
home time, temperature, or run counter
in the bottom row.
8.1 Temperature Mode - Setting
• In temperature mode, press and hold the
[s/+] button for 2 seconds. The ˚F or ˚C indicator will ash.
• Press the [o/-] button to select between ˚F or ˚C.
• Press the [o/o] button to conrm selection.
• At this time the bottom row will ash.
• Press the [o/-] button to select between home time, temperature,
or run counter to be displayed in the bottom row. Press the [o/o]
button to conrm selection.
8.2 Temperature Mode - Temperature Features
Current, Maximum, and Minimum Temperatures:
• In temperature mode, press the [o/-] button to access the
maximum temperature reading since the setting was last reset.
• Press the [o/-] button again to access the minimum temperature
reading since the setting was last reset.
• Both maximum and minimum temperature readings can be reset by
pressing and holding the [s/+] button for 2 seconds while viewing
either the maximum or minimum records respectively.
• Surrounding temperatures are generally 10 - 15˚F / 5 - 8˚C
cooler than watch readings due to the effects of the wearer's body
temperature.
• For more accurate readings, remove the watch from your wrist and
allow 5-10 minutes for sensors to adjust.
9.0 Altimeter Mode - Display
In altitude mode the watch will display
altitude and barometric measurements
in the top row and the current home
time, current temperature, or run counter
depending our your personal selection.
•
To view Altimeter Mode, press the
[m] button until the mode indicator
displays A.
16
17
9.1 Altimeter Mode - Setting
• In altimeter mode, press and hold the [s/+] button for 2 seconds.
• The current altitude reading will ash.
• Using the [s/+] and [o/-] buttons, enter your reference altitude.
Your reference altitude should be obtained from a reliable map
source for your current altitude.
• Once you have researched and entered your reference altitude,
press the [o/o] button to conrm selection.
• The ft/m indicator will now ash.
• Press the [o/-] button to select your desired unit of measurement.
Press the [o/o] button to conrm selection.
• Altimeter mode also has an optional lock feature.
• Press the [o/o] button to lock altimeter mode and prevent any
accidental recordings of changes in altitude.
9.2 Altimeter Mode - Maximum Altitude
• In altimeter mode, press the [o/-] button to view the maximum
altitude.
• The maximum altitude is the highest altitude recorded since the
feature was last reset.
• To reset the maximum altitude, press and hold the [s/+] button for
2 seconds.
9.3 Altimeter Mode - Barometric Pressure
• In altimeter mode, press the [0/-] button to view the current
barometric pressure.
• To change the unit of measure, press and hold the [s/+] button for
2 seconds.
• The inHG / mbar indicator will ash.
• Use the [o/-] button to select your desired unit of measurement.
Press the [o/o] button to conrm your selection.
10.0 Descent Mode - Display
In descent mode, the watch will display
altitude descent measurements on the
top row and the current home time,
current temperature, or the run counter
on the second row depending on your
personal preference.
• To view descent mode, press the [m]
button until the mode indicator displays
the down arrow.
18
19
10.1 Descent Mode - Trip Descent
• In descent mode, the default view is the total trip descent view.
• To clear/reset the total trip descent, press and hold the [s/+]
button for 2 seconds.
10.2 Descent Mode - Rate of Descent
• In descent mode, press the [o/-] button once to view the current
rate of descent.
• To clear/reset the current rate of descent, press and hold the
[s/+] button for 2 seconds. Note that the current rate of descent
automatically recalculates every minute also.
10.3 Descent Mode - Maximum Rate of Descent
• In descent mode, press the [o/-] button twice to view the maximum
rate of descent for the trip.
• To clear/reset the maximum rate of descent, press and hold the
[s/+] button for 2 seconds.
10.4 Descent Mode - Total Daily Descent
• In descent mode, press the [o/-] button 3 times to view the total
daily descent.
• The total daily descent is automatically reset at midnight.
10.5 Descent Mode - Total Lifetime Descent
• In descent mode, press the [o/-] button 4 times to view the total
lifetime descent.
• To clear/reset the total lifetime descent, press and hold the [s/+]
button for 2 seconds.
11.0 Ascent Mode - Display
In ascent mode, the watch will display the
total trip ascent on the top row and the
current home time, current temperature,
or the run counter on the second row
depending on your personal preference.
•
To view ascent mode, press the [m] button
until the mode indicator displays the up
arrow.
11.1 Ascent Mode - Trip Ascent
• In ascent mode, the default view is the total trip ascent view.
• To clear/reset the current rate of ascent, press and hold the [s/+]
button for 2 seconds.
Indice
Altri manuali Tech4o Orologio
